Designing Winder Treads with Angles
From How to Lay Out Winder Stairs · Step 5 of 7 · Video by stairbuilding

Showing 2:44–3:55 of the source video. Watch the full video with every moment.
What happens in this clip
Learn a geometric method for designing winder treads in a 90-degree corner. This method is often used for 3-step winders. You divide the 90-degree corner with lines at specific angles. The center tread is created by a line at 45 degrees. The other two treads are created by lines at 22.5 degrees from the starting and ending walls. This angular division helps to create a more balanced and potentially code-compliant distribution of the winder treads.
Goal: Learn to use angular divisions to lay out winder treads.
What's used
Tools
- Drafting software or protractor
- Digital angle finder
- T-square and triangles
About the full video
This video provides a detailed conceptual explanation of how to design winder and curved stairways, focusing on the interpretation of building codes related to the 'walk line'. It explores different design challenges and potential solutions using geometric principles, particularly concentric circles, to ensure stair treads meet safety and code requirements.
What's said in this clip
equal sized steps along the path instead of dealing with something like this. Next step let's go ahead and take a look at how winders are affected by concentric circles and how they might be interpreted by your local building department. So here we have a three step winder. One, two, three inside of a square however it could be a rectangle and instead of three steps you could always have two steps again using a walkline with the same measurement for each step. However this won't work if you start thinking outside the box and think that you can split these units of measurement up and draw your lines from the center and I actually stumbled across this pattern by drawing these lines here so thought I would share it with you and provide you with something that is going to produce measurements that are going to be different sizes along the walkline and since we have a 90 degree corner here the one in the center is going to be 45 degrees and the other two measurements this one and this one will be half of 45 or 22 and a half degrees for those of you trying to figure out a different way to design a four step winder that would have the same measurements along the walkline
Automatically transcribed from the source video.
Step 5 of 7: Determine Winder Tread Layout
This is the most critical step for winder stairs. The layout involves creating a series of angled lines that represent the edge of each winder tread. The narrowest point of the winder tread (at the inside of the turn) must be at least 6 inches wide to meet code. The widest point (at the outside of the turn) will be determined by the overall stair width and the angle of the turn. Use geometry and precise measurements to ensure the tread's 'walking line' (typically 12 inches from the outer edge) has the required depth and that the tread is not excessively tapered. This often involves using a compass or string to draw arcs at the inner and outer edges of the turn.
Every video in How to Lay Out Winder Stairs
Step 1: Determine Total Rise and Run
- 2:54–4:34 Determine the Total Rise
- 0:16–1:17 Measure and Calculate Total Rise
- 0:04–0:30 Measure Total Rise
Step 2: Calculate Number of Treads and Risers
- 2:59–6:51 Calculate Number of Risers and Treads
- 8:59–9:54 Calculate Number of Risers and Treads
- 0:32–0:54 Calculate Number of Risers
Step 3: Determine Tread Depth and Landing Dimensions
Step 4: Layout the Stair Angle and Width
- 4:54–6:32 Lay Out Stringers
- 6:42–8:10 Lay Out the Stringer Using a Framing Square
- 0:11–1:48 Calculate and Layout Staircase Dimensions
Step 5: Determine Winder Tread Layout
- 8:11–8:46 Plan the L-Shaped Winder Staircase Design
- 6:31–8:31 Layout Code-Compliant Winder Treads with Concentric Circles
- 2:44–3:55 Designing Winder Treads with Angles (this video)
Step 6: Mark Stringers for Winder Treads
- 6:54–8:50 Marking Stringers
- 0:59–1:13 Mark First Step Cuts
- 1:28–2:15 Implement the Nosing Offset Adjustment
Step 7: Cut Stringers
- 9:35–10:04 Cut the Stringer
- 15:28–20:38 Cut Stringers
- 0:42–0:53 Cut the Stringers
How to Lay Out Winder Stairs
This project outlines the process for accurately laying out winder stairs, which feature wedge-shaped treads that turn a corner. The process involves careful measurement, mathematical calculations, and precise marking to ensure safety, code compliance, and aesthetic appeal.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

