powered by

Cut Stringers

From How to Lay Out Winder Stairs · Step 7 of 7 · Video by AwesomeFramers

Showing 15:28–20:38 of the source video. Watch the full video with every moment.

What happens in this clip

Using a 10 1/4-inch circular saw, carefully cut along all the marked lines. For gang-cutting, the saw blade will cut through the top two stringers completely and score the bottom stringer. After cutting the top two, remove them, then use the same screws to re-secure the now-cut top stringer to the scored bottom stringer. Cut the remaining stringer, connecting the scored lines. For the final cuts on the third stringer, use a jigsaw for precision where the circular saw cannot reach, particularly at the inside corners of the steps. Clean up any loose pieces as you go.

Goal: Cut the marked stringers using a circular saw, utilizing the gang-cutting method for efficiency.

What's used

Tools

  • 10 1/4-inch Circular Saw
  • Cordless Drill
  • Hearing Protection
  • Jigsaw
  • Safety Glasses

About the full video

This video provides a detailed guide on how to calculate, mark, and cut stair stringers using mathematical calculations and gang-cutting techniques. It emphasizes the importance of precise measurements for total rise, individual riser height, and tread depth, adjusting for flooring and tread/riser material thickness. The video also highlights the advantages of using LVL (Laminated Veneer Lumber) over traditional lumber for consistency and durability in stair construction.

What's said in this clip

of the house. Pro tip for you. Cutting your stair stringers to minimize the effort and increase the accuracy. By laying them all three on top and cutting through my layout marks, I cut through two and I score the bottom one. Because I've screwed them together, I can pull the top one off. Screw through the same holes on the bottom two. Cut it again with that 10 and 1/4 in saw. And then all I have to do is connect the dots with the jigsaw. Now it's a lot easier on the first one than it is on the second. And really technically it gets harder on the second, a little bit harder on the third. This way they are all basically as identical as we're going to get them. It's also very efficient. So who said being fast is being sloppy? In order for this to work well, you have to take good care of your tools. [screaming] That 10 and 1/4 in saw needs to be able to cut square. You know, imagine it just goes off to the side. will not run out again. The jigsaw, same thing. I like to use these screws. They're bas they're made for deck ledgers. By attaching the outside stringers to the walls, now they are just locked tight. Think of this as building a system. You can't use 2x8s for treads. Exacto. We are using them for riser. Since the stringers are already laid out, just match that layout to the very bottom riser. Pro tip, don't glue the stringer. Glue the riser. This is Advantex subfloor adhesive polyurethane foam to gel. It is stronger than your mother's love for you, but not stronger than my mother's love for me. Notice that those are PWT LVL's for the stair stringers. They are not going to crack, warp, or twist on me like 2x12 can. Translation: bomber stairs, especially once everything is glued and nailed with 3-in ring shank nails. Make sure that bottom stringer is on layout. To keep those stringers nice and straight, do the same thing in the middle on longer runs. The riser is 7 and 7/16. The 2x8 is 7 and 1/4. You know what that means? I don't have to rip the risers. There will be a small gap at the bottom, but that doesn't matter. Since I am correct-handed, I tend to work from right to left. Do the outside stringers first, flushing up the top, and then go ahead and nail the middle. Notice the 1x4 on the side of the stringer. Since we know for sure that this stair is not going to get a skirt, that 1x4 holds the stringers off so that the drywallers can just slip their drywall back without having to make any funky cuts. No, that is not grape jelly. That is the Advantex…

Automatically transcribed from the source video.

Step 7 of 7: Cut Stringers

Using a circular saw or handsaw, carefully cut along all the marked lines on the stringers. Make precise cuts for the tread notches and riser lines. Pay special attention to the angled cuts required for the winder sections to ensure they align perfectly with the winder tread layout. Ensure all cuts are clean and accurate for a tight fit.

Open this step in the guide

Every video in How to Lay Out Winder Stairs

  1. Step 1: Determine Total Rise and Run

  2. Step 2: Calculate Number of Treads and Risers

  3. Step 3: Determine Tread Depth and Landing Dimensions

  4. Step 4: Layout the Stair Angle and Width

  5. Step 5: Determine Winder Tread Layout

  6. Step 6: Mark Stringers for Winder Treads

  7. Step 7: Cut Stringers

How to Lay Out Winder Stairs

This project outlines the process for accurately laying out winder stairs, which feature wedge-shaped treads that turn a corner. The process involves careful measurement, mathematical calculations, and precise marking to ensure safety, code compliance, and aesthetic appeal.

Read the full guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Cut Stringers — How to Lay Out Winder Stairs | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.