Drive and Snap Off the Screw
From How to Use a Squeak-Repair Kit on Carpeted Stairs and Floors · Step 4 of 6 · Video by Home Repair Tutor

Showing 2:48–3:49 of the source video. Watch the full video with every moment.
What happens in this clip
Once the screw and depth control tool are assembled on the drill, align the depth control tool directly over the previously located floor joist. Push the tool firmly down into the carpet to expose the screw tip. Use the drill to drive the screw down through the carpet, subfloor, and into the joist. The depth control tool will automatically stop the screw at the correct depth, preventing it from being over-driven. After the screw is fully seated, a small portion of its head will be slightly visible above the carpet surface. Now, remove the drill. Take the depth control and alignment tool and slide its specialized slot over the exposed screw head. Rock the tool back and forth firmly to engage the scored section of the screw, causing the head to snap off cleanly. The remaining part of the screw will be hidden approximately one inch below the carpet's surface, making the fix invisible and undetectable underfoot. This process effectively pulls the subfloor tightly against the joist, eliminating the squeak.
Goal: Secure the subfloor to the joist and hide the screw head for an invisible repair.
What's used
Tools
- Depth Control and Alignment Tool Squeak No More
- Drill Ridgid
- Specialized Scored Screws Squeak No More
About the full video
This project provides a detailed guide on how to effectively eliminate squeaks in carpeted floors using the 'Squeak No More' kit. It covers methods for accurately locating floor joists underneath carpet, the proper use of the kit's specialized drill bit and depth control tool to drive screws, and how to cleanly snap off the screw heads below the carpet surface without causing damage.
Step 4 of 6: Install Repair Screws
With the pilot holes drilled, insert the repair screws. These screws are typically designed with a break-off head or a mechanism to allow the visible portion to be removed or countersunk. Attach the appropriate screw-driving bit to your drill and carefully drive the screw. Stop when the screw is snug and has effectively pulled the carpet and subfloor tightly together, eliminating the gap causing the squeak. The goal is to create a tight bond that stops movement.
Every video in How to Use a Squeak-Repair Kit on Carpeted Stairs and Floors
Step 1: Identify Squeak Location
- 0:00–0:17 Identify Squeak Location
- 0:00–0:09 Locate the Squeak
- 0:00–0:30 Locate Squeak and Assess Access
Step 2: Prepare the Squeak Repair Kit
Step 3: Drill Pilot Holes
- 0:15–0:24 Drill a Pilot Hole
- 4:17–5:45 Fix from Above: Use Trim Head Screws
- 4:08–4:43 Pre-Drill Pilot Holes
Step 4: Install Repair Screws
- 1:25–3:50 Install Specialized Repair Screws
- 2:56–3:28 Install Breakaway Repair Screws
- 2:48–3:49 Drive and Snap Off the Screw (this video)
Step 5: Break Off Screw Heads (if applicable)
- 3:48–4:38 Break Off the Screw Head
- 4:49–5:22 Snap Off Screw Heads
- 3:50–4:00 Break Off Screw Heads
Step 6: Test the Repaired Area
- 8:01–8:29 Test Repaired Floor
- 3:57–4:25 Repeat for All Squeaky Areas
- 0:38–0:48 Confirm Repair and Concealment
How to Use a Squeak-Repair Kit on Carpeted Stairs and Floors
Outline for using a squeak-repair kit on carpeted stairs and floors to eliminate annoying squeaking sounds.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

