powered by

Power Up and Test

From How to Cut and Join LED Strip Lights Around Stair Corners · Step 6 of 7 · Video by Lepro

Showing 1:11–1:33 of the source video. Watch the full video with every moment.

What happens in this clip

Once your strip lights are secured, attach the end of the LED strip to the controller. Then, connect the controller to the power adapter. Finally, plug the power adapter into an electrical outlet. Before using the remote control, remove the insulation sheet (plastic tab) from the battery compartment. After removing the sheet, you can press any color button on the remote control to change and test the lighting color, ensuring everything is working correctly.

Goal: Connect power to the strip lights and verify functionality

What's used

Tools

  • Controller Lepro
  • Electrical Outlet
  • LED Strip Lights Lepro
  • Power Adapter Lepro
  • Remote Control Lepro
  • Wall-mounted controller

About the full video

This project provides a comprehensive guide on how to install, cut, and connect LED strip lights to create beautiful mood lighting in any room or area. It covers surface preparation, adhering the lights, optional security clips, connecting power, cutting the strips, and using various connectors for turns and uneven surfaces.

What's said in this clip

if you choose you can secure the clip further by screwing it to the surface once your strip lights are secured you can attach it to the controller and power adapter then plug it into an electrical outlet using the remote control remove the installation sheet first press any color on the remote control to change the lighting color

Automatically transcribed from the source video.

Step 6 of 7: Connect Power Supply and Test

Connect the input end of your first LED strip segment (or the end of the main run) to the power supply. This typically involves connecting a low-voltage wire from the power adapter to the appropriate input terminals on the LED strip, ensuring correct polarity (+ to +, - to -). If using a controller for dimming or color changes, wire the LED strip to the controller's output and the power supply to the controller's input. Plug in the power supply and test all segments of the LED strip to ensure they light up correctly and consistently. Check for any flickering or dead sections.

Open this step in the guide

Every video in How to Cut and Join LED Strip Lights Around Stair Corners

  1. Step 1: Plan LED Strip Layout

  2. Step 2: Cut LED Strips to Length

  3. Step 3: Prepare LED Strip Ends for Connection

  4. Step 4: Join LED Strips (if necessary)

  5. Step 5: Mount LED Strips to Stairs

  6. Step 6: Connect Power Supply and Test

  7. Step 7: Secure and Conceal Wiring

Questions about How to Cut and Join LED Strip Lights Around Stair Corners

Do I really need to solder to join LED strips around stair corners, or are there easier methods?

While soldering provides the most reliable and secure connection for long-term use, you can also use solderless connectors. The project lists L-shape connectors (P700016-000) specifically for corners, which can be an easier alternative if you're uncomfortable with soldering. Ensure they are compatible with your LED strip's width and pin configuration.

What are the most common mistakes beginners make when cutting and joining LED strips, and how can I avoid them?

A common mistake is cutting the LED strip anywhere other than the designated cut lines, which will damage the circuit. Always ensure you align the positive and negative terminals correctly when joining strips, as reversed polarity will prevent them from lighting up. Additionally, make sure all connections, whether soldered or solderless, are firm to prevent flickering or disconnections.

What safety precautions should I take when using a soldering iron and working with low-voltage electrical components?

When soldering, always work in a well-ventilated area to avoid inhaling fumes, and use a heat-resistant mat to protect your work surface. Be extremely careful as soldering irons get very hot. For all electrical work, even low-voltage, always disconnect the power supply before making or adjusting any connections to prevent short circuits.

How can I ensure my LED strips stay securely attached to the stairs, especially around corners?

To ensure secure adhesion, clean the stair surface thoroughly before applying the strips. Use the adhesion promoter (like 3M Automotive Adhesion Promoter) as directed, followed by the LED strip's adhesive backing. You can reinforce with strong double-sided mounting tape, especially on curved areas or corners, for extra security.

The project difficulty is 'beginner,' but what specific skills will I need to learn or practice for this?

As a beginner, the main skills to practice for this project are precise cutting of the LED strips at marked points and basic soldering techniques if you choose that method. Understanding polarity (positive/negative) is also crucial for proper connections. Watching a few video tutorials on these specific tasks beforehand can greatly increase your confidence and success.

What should I do if my LED strip doesn't light up after installation, or only part of it works?

First, ensure the power supply is properly connected and receiving power. Then, carefully check all your connections, both at the power supply and between LED strip segments, to confirm they are secure and that polarity (positive to positive, negative to negative) is correct. Inspect your cut points to ensure no circuits were damaged and that the connection points are clean.

How to Cut and Join LED Strip Lights Around Stair Corners

A high-level outline for installing LED strip lights around stair corners, focusing on cutting, joining, and mounting techniques.

Read the full guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Power Up and Test — How to Cut and Join LED Strip Lights Around Stair Corners | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.