powered by

Plan Light Placement and Spacing

From How to Cut and Join LED Strip Lights Around Stair Corners · Step 1 of 7 · Video by Premier Outdoor Living

Showing 5:35–6:58 of the source video. Watch the full video with every moment.

What happens in this clip

Before installing the lights, carefully plan their placement on the stair risers. For wrap-around steps, it's recommended to stagger the lights rather than placing them in a straight line to achieve a more aesthetically pleasing cascading effect. Identify the midpoint of each riser, and then measure out equal distances (e.g., 3 feet) from the center in both directions to mark the light positions. Use masking tape or a marker to indicate the precise locations where each light will be installed.

Goal: Determine the optimal and aesthetically pleasing layout for step lights.

What's used

Tools

  • Marker/Pencil
  • Masking Tape
  • Tape Measure

About the full video

This project details the installation of low-voltage strip lighting onto deck steps to enhance safety and aesthetics. It covers planning the layout for optimal visual appeal, installing the individual lights into pre-drilled holes in the stair risers, connecting them using a plug-and-play wiring system with splitters, and managing the wiring for a clean finish. The video emphasizes a staggered light pattern for wrap-around steps.

What's said in this clip

hey what are you doing there sean oh um i'm actually getting ready to uh prep for all of these decorators riser lights that we're gonna be putting in so this is a little bit complicated because we have these wrap around stairs whenever we have these you can see each tread is a little bit longer than the one before it we don't want to just do straight lines we want to stagger them and it just looks a little bit nicer so what i like to do start on my middle riser i find my middle point that's right there and then we do an offset off of that so right now i'm doing the three foot spacing between lights so i pulled three feet off in both directions so on this riser right in between these two lights and then from this one to this one we have that three foot spacing and then it's going to be the same on this bottom riser what do you think [Music] that's good so you can see because we staggered them we have this our top and bottom riser are lining up but because this one is about two feet longer we get an extra light here so it looks like it cascades down this corner but all the spacing is still the same if you have them just in straight lines it gets really wacky looking in this corner because you could either go light light light but then you have this big open space and it just looks a little a little weird so we like to do it like this on wrap around stairs and uh a lot of lights

Automatically transcribed from the source video.

Step 1 of 7: Plan LED Strip Layout

Before cutting any LEDs or wires, carefully plan where each strip will be placed. Typically, this involves running the LED strip along the edge of each stair tread or riser. Mark the starting and ending points for each segment. Consider the location of the power supply and how the wires will be discreetly routed. Plan for any corner turns or transitions between steps. This planning phase is crucial for ensuring a clean and professional-looking installation and for calculating the correct amount of LED strip and wire needed.

Open this step in the guide

Every video in How to Cut and Join LED Strip Lights Around Stair Corners

  1. Step 1: Plan LED Strip Layout

  2. Step 2: Cut LED Strips to Length

  3. Step 3: Prepare LED Strip Ends for Connection

  4. Step 4: Join LED Strips (if necessary)

  5. Step 5: Mount LED Strips to Stairs

  6. Step 6: Connect Power Supply and Test

  7. Step 7: Secure and Conceal Wiring

Questions about How to Cut and Join LED Strip Lights Around Stair Corners

Do I really need to solder to join LED strips around stair corners, or are there easier methods?

While soldering provides the most reliable and secure connection for long-term use, you can also use solderless connectors. The project lists L-shape connectors (P700016-000) specifically for corners, which can be an easier alternative if you're uncomfortable with soldering. Ensure they are compatible with your LED strip's width and pin configuration.

What are the most common mistakes beginners make when cutting and joining LED strips, and how can I avoid them?

A common mistake is cutting the LED strip anywhere other than the designated cut lines, which will damage the circuit. Always ensure you align the positive and negative terminals correctly when joining strips, as reversed polarity will prevent them from lighting up. Additionally, make sure all connections, whether soldered or solderless, are firm to prevent flickering or disconnections.

What safety precautions should I take when using a soldering iron and working with low-voltage electrical components?

When soldering, always work in a well-ventilated area to avoid inhaling fumes, and use a heat-resistant mat to protect your work surface. Be extremely careful as soldering irons get very hot. For all electrical work, even low-voltage, always disconnect the power supply before making or adjusting any connections to prevent short circuits.

How can I ensure my LED strips stay securely attached to the stairs, especially around corners?

To ensure secure adhesion, clean the stair surface thoroughly before applying the strips. Use the adhesion promoter (like 3M Automotive Adhesion Promoter) as directed, followed by the LED strip's adhesive backing. You can reinforce with strong double-sided mounting tape, especially on curved areas or corners, for extra security.

The project difficulty is 'beginner,' but what specific skills will I need to learn or practice for this?

As a beginner, the main skills to practice for this project are precise cutting of the LED strips at marked points and basic soldering techniques if you choose that method. Understanding polarity (positive/negative) is also crucial for proper connections. Watching a few video tutorials on these specific tasks beforehand can greatly increase your confidence and success.

What should I do if my LED strip doesn't light up after installation, or only part of it works?

First, ensure the power supply is properly connected and receiving power. Then, carefully check all your connections, both at the power supply and between LED strip segments, to confirm they are secure and that polarity (positive to positive, negative to negative) is correct. Inspect your cut points to ensure no circuits were damaged and that the connection points are clean.

How to Cut and Join LED Strip Lights Around Stair Corners

A high-level outline for installing LED strip lights around stair corners, focusing on cutting, joining, and mounting techniques.

Read the full guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Plan Light Placement and Spacing — How to Cut and Join LED Strip Lights Around Stair Corners | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.