Install Stair Handrails and Cut Posts
From How to Install a Deck Stair Railing · Step 2 of 6 · Video by How-Tos With Aaron

Showing 2:45–3:58 of the source video. Watch the full video with every moment.
What happens in this clip
For handrails on stairs, begin by clamping a 2x4 piece of lumber in place along the angle of the stairs, ensuring consistent gaps over each step. Use a pencil to mark the precise cut lines on the 2x4 where it meets the posts. Take the marked 2x4 to a miter saw and cut it according to your pencil lines. Install the cut 2x4 rails at the top and bottom of the stair section, securing them with screws. Determine the desired height for the top of the handrail, typically 36 to 40 inches from the deck height. Mark this height on the stair post, then mark an inch lower to account for the thickness of the deck board that will cap the handrail. Cut the post at this marked line using a skill saw and a Sawzall.
Goal: Fit and install handrails for stair sections and trim posts to height
What's used
Tools
- 2x4 Lumber
- Clamps
- F-clamps
- Drill/Driver DeWalt
- Miter Saw
- Pencil
- Sawzall (Reciprocating Saw)
- Screws
- Skill Saw (Circular Saw)
- Tape Measure
About the full video
This project guides you through building a sturdy wooden handrail for a deck, including both flat sections and stair sections. It utilizes 2x4 lumber for the structural rails and spindles, with a deck board for the top handrail. Key techniques involve securing posts, precise spindle spacing using a spacer, efficient batch cutting of spindles with a stop block, and fitting handrails to stair angles.
Step 2 of 6: Cut and Attach Railing Posts
Cut wooden posts for the railing to the appropriate height, typically from the base of the stringer to the marked railing height, plus extra for attachment. Using appropriate fasteners such as lag screws or structural screws, securely attach the posts to the stair stringers. Ensure posts are plumb and stable.
Every video in How to Install a Deck Stair Railing
Step 1: Measure and Mark Stair Stringers
- 0:13–1:16 Measure and Mark Handrail Height
- 1:30–2:18 Determine and Mark Handrail Height
- 0:02–0:15 Measure and Mark Railing Height and Studs
Step 2: Cut and Attach Railing Posts
- 0:30–0:41 Install Stair Railing Posts
- 3:39–4:33 Install Newel Posts Securely
- 2:45–3:58 Install Stair Handrails and Cut Posts (this video)
Step 3: Install Top and Bottom Rails
- 0:51–1:08 Install Top and Bottom Rails
- 0:49–1:01 Install Top and Bottom Rails
- 2:16–2:28 Measure and Cut Top and Bottom Rails
Step 4: Install Balusters (Spindles)
- 1:01–1:29 Attach Balusters
- 1:10–1:35 Install Balusters
- 3:09–4:49 Install Balusters
Step 5: Attach Handrail
- 4:49–5:12 Install Handrail
- 2:44–3:05 Cut and Fit Handrail
- 6:26–8:27 Install Top Handrail
Step 6: Final Inspection and Safety Check
- 0:16–0:28 Perform Final Inspection and Safety Check
- 0:22–0:25 Final Visual Inspection
- 0:54–0:59 Final Inspection & Completion
How to Install a Deck Stair Railing
This project outlines the steps for installing a railing system for deck stairs, ensuring safety and code compliance. It covers measuring, cutting, assembling, and securely attaching railing components.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

