powered by

Install Left Gate Mounts

From How to Install a Pet Gate at the Bottom of Stairs · Step 3 of 5 · Video by Carlson Pet Products

Showing 1:18–1:38 of the source video. Watch the full video with every moment.

What happens in this clip

Now, align the lower gate mount with the drilled holes on the main gate side of the opening. If there is a baseboard or trim creating a gap between the mount and the wall, use the wall spacers to fill this gap. Make sure the width of the wall spacers matches the width of your trim for a flush fit. Once correctly positioned, use your screwdriver to fasten the 1-inch screws through the mount and into the wall (and anchors if applicable). Repeat this process for the upper gate mount, ensuring it's vertically aligned with the lower mount.

Goal: Securely attach the retractable gate's main mounting brackets to the wall

What's used

Tools

  • 1-inch Screws
  • Lower Gate Mount
  • Screwdriver
  • Upper Gate Mount
  • Wall Spacers

About the full video

This project provides step-by-step instructions for installing a Carlson retractable gate. The process includes using paper templates to mark mounting locations, drilling appropriate holes for studs or drywall, securing the gate and handle mounts with screws and wall anchors, and finally attaching and operating the retractable gate.

What's said in this clip

guide marks and insert plastic wall anchors align Upper and Lower Gate mounts and handle mounts to designated areas by using a screwdriver to fasten the one inch screws use wall spacers with wall mounts to fill gap between wall and skirt slash baseboard make sure the width of the wall spacers matches the width of your trim align Upper and Lower Gate mounts and handle mounts to designated areas by

Automatically transcribed from the source video.

Step 3 of 5: Install Mounting Hardware

Following the gate manufacturer's instructions, drill pilot holes at each marked location. The size of the pilot hole should be slightly smaller than the diameter of the screws provided. If mounting to a stud, ensure the screw penetrates well into the stud. If using drywall anchors, install them according to their specific instructions. Once pilot holes are drilled (and anchors installed if needed), align the mounting brackets or hinges with the holes and drive the screws firmly to secure them to the surface. Ensure all hardware is tightly fastened.

Open this step in the guide

Every video in How to Install a Pet Gate at the Bottom of Stairs

  1. Step 1: Select Gate Type and Location

  2. Step 2: Mark Mounting Positions

  3. Step 3: Install Mounting Hardware

  4. Step 4: Attach Gate to Hardware

  5. Step 5: Adjust and Test Latch Mechanism

Questions about How to Install a Pet Gate at the Bottom of Stairs

What kind of pet gate is best for the bottom of stairs, especially if it also needs to be safe for children?

For stair applications, always choose a hardware-mounted gate, as pressure-mounted gates are not secure enough and can pose a fall risk. Look for gates that specify they meet ASTM safety standards (like the Regalo or Safety 1st models) if children will also be using them. These gates offer superior stability and security.

What should I do if I can't find a stud exactly where I need to mount the gate hardware?

While mounting into a stud provides the strongest attachment, you can use heavy-duty drywall anchors, such as the E-Z Ancor toggles mentioned, in plaster or drywall. Ensure these anchors are rated for significant pull-out force. Always test the security of the installed hardware vigorously before attaching the gate.

How can I ensure the gate is installed perfectly level, and the latch mechanism works smoothly?

Use a level to accurately mark all your mounting positions before drilling, especially for the top and bottom brackets on both sides. Once the gate is attached, carefully adjust any hinge tension screws and check the alignment of the latch strike plate. A properly installed gate should swing freely and latch securely with minimal effort.

What are the most common mistakes beginners make when installing a pet gate at the bottom of stairs?

A frequent mistake is not ensuring secure mounting by either missing a stud or using inadequate anchors, which can compromise safety. Another common error is not thoroughly testing the latch mechanism and overall stability after installation. Always double-check all connections and confirm the gate can withstand reasonable force.

Do I need any specialized tools for this project, or will basic household tools suffice?

A stud finder (like the DEWALT DW0150) is strongly recommended to locate studs for the most secure mounting, which is crucial for stair gates. While a drill, drill bits, and a screwdriver are common, ensure you have the correct bit sizes for the gate's mounting hardware. These tools help ensure precise and safe installation.

How can I install a gate if I don't want to drill directly into my wooden banister or baseboards?

For banisters, consider using banister mounting kits that secure the gate with straps or clamps without drilling into the wood. If your baseboards interfere, you might need to use wood shims or spacers behind the mounting brackets to ensure the gate hangs plumb and clears any trim. Always verify that such alternative mounting methods remain structurally sound.

How to Install a Pet Gate at the Bottom of Stairs

Outline for installing a pet gate at the bottom of stairs, focusing on secure mounting and ensuring safety for pets and children.

Read the full guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Install Left Gate Mounts — How to Install a Pet Gate at the Bottom of Stairs | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.