Cut Handrail for Returns
From How to Install a Handrail Return at the End of a Rail · Step 2 of 6 · Video by Rusty Dog & Co.

Showing 4:05–5:23 of the source video. Watch the full video with every moment.
What happens in this clip
The handrail used is a 12-foot oak handrail. Using a miter saw, cut the ends of the handrail at 45-degree angles. This creates a 'return' that will attach to the wall, providing a safer and more aesthetically pleasing finish by preventing clothing or bags from getting caught. When making the cut, measure 1.5 inches from the edge of the handrail and make the 45-degree cut, ensuring this measurement is from the shortest point of the angle. Cut one side, then move the saw to cut the other side at a 45-degree angle in the opposite direction. Save the cut-off return pieces.
What's used
Tools
- Clamps
- Miter Saw DeWalt
- Oak Handrail unknown (purchased from Lowe's)
- Tape Measure
About the full video
This video demonstrates the step-by-step process of installing a new wooden handrail on a staircase. It covers measuring for proper height and angle, locating wall studs, cutting the handrail to size with appropriate angles, assembling the return pieces, and securely mounting the handrail to the wall brackets. Note: The user prompt describes 'refinishing via stain application', however, the video demonstrates the installation of a new handrail and only briefly mentions applying finish off-camera, without showing any staining or surface preparation for refinishing.
What's said in this clip
and installed the handrail that we would be installing was a 12 foot okay rail that we picked up from Lowe's now I will admit that even 12 feet was not quite long enough for this particular staircase but it was close enough that we went with it rather than buying two and joining them together now typically you want the handrail to be longer than the staircase though if you can I knew that I wanted to cut this handrail at 45 degree angles on the ends so that I could return it to the wall now if you've ever gotten anything caught on a railing that's not returned to the wall well then you know why I chose to do this I think it looks better and it's a little bit safer plus building code also recommends this distance to allow your hand to freely use the handrail without scraping against the wall to cut this handrail I measured one and a half inches from my Edge and made a mark now I'm going to make a 45 degree cut making sure that my one and a half inches is for my shortest point of the angle this will help ensure that my distance is the same for each end once I had one side cut I saved that piece because it's actually going to be attached to my opposite side and vice versa once I had one side cut then I moved my saw to cut at 45 degrees in the opposite direction and cut the other side the same way
Automatically transcribed from the source video.
Step 2 of 6: Prepare Handrail End for Return
Depending on the type of return (e.g., volute, easing, or a simple angle), you may need to cut the existing handrail end to a specific angle or shape. This often involves using a miter saw or coping saw to create a clean joint. For some returns, a specific fitting may require a pre-cut notch or end profile.
Every video in How to Install a Handrail Return at the End of a Rail
Step 1: Mark Handrail Return Position
Step 2: Prepare Handrail End for Return
- 2:44–3:32 Cut Handrail Ends for Returns
- 4:05–5:23 Cut Handrail for Returns (this video)
- 2:44–3:21 Cut Handrail Ends with Miter Saw
Step 3: Fit and Test Handrail Return
- 4:24–5:10 Final Handrail Installation and Stability Check
- 5:43–5:52 Dry Fit Handrail over Balusters
- 5:22–5:43 Shape Handrail Return Ends
Step 4: Secure Handrail Return to Handrail
- 4:26–5:07 Gluing and Fastening the Return Piece
- 9:58–10:29 Fabricate and Install Handrail Return
- 3:32–4:24 Assemble Handrail End Returns
Step 5: Mount Handrail Assembly to Wall/Newel Post
- 0:54–1:00 Connect Handrail to Newel Post
- 12:33–14:45 Install Handrail to Newel Post and Wall
- 0:15–0:22 Attach Handrail to Newel Post
Step 6: Finish and Inspect
- 1:53–2:04 Final Sanding and Cleaning
- 0:28–0:36 Finishing and Sealing
- 0:43–0:46 Finishing Touches (Sanding, Finishing, Caulk)
Questions about How to Install a Handrail Return at the End of a Rail
Do I absolutely need a miter saw for this project, or are there alternatives for cutting the handrail return?
A miter saw provides precise, clean cuts essential for a tight-fitting handrail return, especially for angled returns. While you could use a handsaw with a miter box, it requires more effort and might not achieve the accuracy needed for a professional finish. For the best results and easier work, a miter saw is highly recommended.
What critical safety steps should I take when cutting and installing the handrail return?
Always wear safety goggles when using power tools like a miter saw and drill to protect your eyes from debris. Ensure your handrail and return pieces are securely clamped before cutting or drilling to prevent movement and potential injury. Work in a well-lit area and keep your workspace clear of obstructions.
What's the biggest mistake beginners make with handrail returns, and how can I avoid it?
A common mistake is inaccurate measuring or cutting, leading to noticeable gaps where the return meets the main handrail or wall. To avoid this, always measure twice and cut once. Perform dry-fits of the return multiple times before applying any adhesive or performing final fastening to ensure a perfect fit.
Is the 4-hour estimate realistic for a beginner, and what makes this project suitable for DIYers?
Yes, 4 hours is a realistic estimate for beginners, assuming you have the necessary tools and a basic understanding of their operation. This project is beginner-friendly because it involves straightforward measuring, cutting, and fastening steps. Taking your time with each stage, especially precise measurements and dry-fitting, will contribute to a successful outcome.
How do I ensure the handrail return matches up perfectly with my existing handrail for a seamless look?
Achieving a seamless look depends on precise cuts and a snug fit between the return and the main handrail. Carefully mark your cut lines, and if your return is unfinished, match its stain or paint to your existing handrail after installation for a cohesive appearance. Slight gaps can sometimes be filled with wood putty before finishing.
How do I ensure the handrail return is securely attached to both the main handrail and the wall?
For the handrail-to-return connection, use strong construction adhesive along with screws, pre-drilling pilot holes to prevent splitting. When mounting the entire handrail assembly to the wall, always use a stud finder to locate wall studs and fasten directly into them for maximum security. If a stud isn't available, use appropriate heavy-duty wall anchors designed for the weight of a handrail.
How to Install a Handrail Return at the End of a Rail
This project outlines the steps to properly install a handrail return, which is the curved or angled section at the end of a handrail that transitions it back to the wall or newel post. This ensures a safe and aesthetically pleasing finish.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

