Attach Handrail to Brackets
From How to Install a Handrail on a Spiral Staircase · Step 6 of 8 · Video by Optimum Works Inc.

Showing 2:44–4:28 of the source video. Watch the full video with every moment.
What happens in this clip
With the brackets loosely installed, carefully lift the handrail and place it onto the brackets, aligning it with the marked chalk line. It is highly recommended to have an assistant to help hold the handrail firmly in place during this step. Once the handrail is resting securely on the brackets, use the self-tapping screws provided to fasten the handrail to each bracket. If you find it difficult to apply enough pressure for the self-tapping screws to bite into the metal handrail, pre-drill a small pilot hole through the handrail material (using a drill bit 1/16 inch smaller than the screw diameter) before driving the self-tapping screw. Ensure all screws are fully tightened, making the handrail sturdy and secure.
Goal: Permanently attach the handrail to the installed brackets
What's used
Tools
- Electric Drill DeWalt
- Handrail Brackets Optimum Works
- holding the handrail
- Handrail Optimum Works
- being mounted
- Pilot Hole Drill Bit (for metal) Unbranded
- Self-Tapping Screws Unbranded
About the full video
This project provides a step-by-step guide on how to install a handrail on a staircase. The process involves accurately marking the handrail's height and angle, locating wall studs for secure bracket placement, drilling pilot holes, and then fastening the brackets and handrail using appropriate screws or bolts. An alternative method for securing brackets using drywall anchors when studs are not accessible is also demonstrated.
Step 6 of 8: Attach Handrail to Brackets
Carefully place the handrail sections onto the support brackets, aligning them with the pre-drilled holes or designated attachment points on the brackets. Depending on the bracket design, you may use screws from below, set screws, or other fastening methods to firmly attach the handrail to each bracket. Ensure the handrail is level and follows the intended line of the staircase.
Every video in How to Install a Handrail on a Spiral Staircase
Step 1: Measure and Mark Handrail Length
- 0:07–0:51 Measure Staircase Length and Angle
- 0:00–0:43 Measure and Cut Handrail
- 2:28–2:44 Measure and Mark Railing for Cuts
Step 2: Cut Handrail Material
- 2:44–3:05 Cut and Fit Handrail
- 0:11–0:13 Cutting Handrail Sections
- 0:00–0:43 Measure and Cut Handrail
Step 3: Prepare Handrail Ends for Connection
Step 4: Locate and Mark Support Brackets
- 2:32–3:05 Mark Top Bracket Location
- 3:05–4:05 Install Mounting Brackets
- 1:23–2:32 Locate Studs and Mark Bottom Bracket
Step 5: Install Handrail Support Brackets
- 2:28–2:44 Install Brackets and Mount Handrail
- 1:13–1:22 Install End Rail Brackets
- 8:12–9:58 Install Handrail Brackets
Step 6: Attach Handrail to Brackets
- 3:35–3:56 Mount Handrail to Brackets
- 2:44–4:28 Attach Handrail to Brackets (this video)
- 7:17–9:36 Install Handrail and Brackets
Step 7: Join Handrail Sections (if applicable)
- 0:13–0:20 Initial Handrail Attachment and Joining
- 0:09–0:12 Assemble Handrail Sections
- 0:21–0:27 Completing Handrail Attachment
Step 8: Inspect and Test Handrail Stability
- 5:36–5:45 Final Check
- 9:33–11:59 Final Inspection and Verification
- 0:07–0:08 Secure and Test the Railing Section
How to Install a Handrail on a Spiral Staircase
Install a handrail on a spiral staircase to improve safety and accessibility. This involves measuring, cutting, and securely attaching the handrail to the staircase structure.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

