powered by

Secure Treads to Stairs

From How to Install Carpet Treads on High-Gloss Polyurethane Stairs · Step 5 of 5 · Video by Ready Set Build It

Showing 3:25–4:32 of the source video. Watch the full video with every moment.

What happens in this clip

To install the prepared carpet tread, first ensure your alignment is correct. You can use a laser level to project a straight line from the wall across the stair, or simply use a tape measure to ensure consistent spacing from the wall for each tread. Once aligned, carefully place the tread onto the stair, ensuring the adhesive side makes contact with the hardwood. Apply firm pressure across the entire surface of the tread, using your feet or a specialized roller tool, to ensure the double-sided tape adheres completely and securely to the stair.

Goal: Securely attach each carpet tread to the hardwood stair.

What's used

Tools

  • Carpet Treads (with tape applied) Canyon
  • Laser Level
  • Chalk line
  • Roller Tool
  • Tape Measure

About the full video

This project provides a step-by-step guide on how to install carpet treads on hardwood stairs using double-sided carpet tape. The process involves preparing the treads, accurately positioning them, and securing them to enhance safety and aesthetics without requiring advanced tools or skills.

What's said in this clip

like i said you can use a tape measure come off the wall and see how much you got for spacing there but what i'm going to do is i'm going to try to duck down so you guys can see it but i have my laser level line here i have my green laser level line i don't know if you guys can actually see it hold up the tape measure here [Music] i'll try to zoom in and get a zoom in shot for you guys so you can see what it is so it's about six and a half inches off the wall and then i'll just go ahead and stick this down and then press it down to make sure it's matted [Music] so i'm just going to line it up here with my laser line press it down [Music] you can use one of those nice little rollers or you can use your feet like i'm using just to make sure they're pressed in that's it we'll just do that all the way up and we'll be done

Automatically transcribed from the source video.

Step 5 of 5: Secure Edges and Nosing

Pay special attention to the edges and the nosing of each installed carpet tread. Press down firmly along these areas to ensure a strong bond. If any part of the edge seems loose, apply additional pressure or a small amount of appropriate adhesive specifically to the edge and press it down.

Open this step in the guide

Every video in How to Install Carpet Treads on High-Gloss Polyurethane Stairs

  1. Step 1: Clean Stair Treads

  2. Step 2: Dry Fit Carpet Treads

  3. Step 3: Apply Adhesive (if necessary)

  4. Step 4: Install Carpet Tread

  5. Step 5: Secure Edges and Nosing

Questions about How to Install Carpet Treads on High-Gloss Polyurethane Stairs

How do I ensure the carpet treads will securely stick to my high-gloss polyurethane stairs?

Thoroughly clean the stairs with a degreaser and dry them completely before application to ensure optimal adhesion. Use a strong construction adhesive like Titebond, applied with a V-notch spreader, especially if your treads are not peel-and-stick or for added security. Allow adequate curing time for the adhesive before heavy use.

What specific preparation is needed for high-gloss polyurethane stairs before installing carpet treads?

Start by sweeping or vacuuming the stairs to remove loose debris. Then, use a microfiber cloth with a good cleaner to remove all dirt, grease, and any residue, ensuring the surface is completely clean and dry. A clean, smooth surface is crucial for the adhesive to bond effectively.

What if the pre-made carpet treads don't perfectly fit my stair dimensions?

It's important to measure your stair treads before purchasing to ensure a good fit. If your stairs require custom sizing, you may need to carefully trim larger treads with a sharp utility knife or seek out treads available in different dimensions. Ensure the treads don't hang over the edge excessively to prevent tripping hazards.

What are common mistakes beginners make when installing carpet treads, and how can I avoid them?

A common mistake is not cleaning the stairs thoroughly, which leads to poor adhesion. Another is improper or inconsistent placement; always dry-fit each tread first and use painter's tape as guides for consistent alignment. Also, ensure you apply enough adhesive, especially on the edges and nosing, to prevent curling or lifting over time.

My treads are peel-and-stick; do I still need additional adhesive like E6000 or Titebond?

While peel-and-stick treads offer convenience, for high-gloss polyurethane stairs, supplementary adhesive is often recommended for maximum security and longevity. E6000 Fabri-Fuse is excellent for fabric-to-surface bonds, while Titebond construction adhesive provides a very strong, permanent hold, especially at edges and nosing that see more wear.

What safety precautions should I take during this carpet tread installation project?

Work in a well-ventilated area when using adhesives to avoid inhaling fumes. Ensure the stairs are clear of obstacles, well-lit, and that you have stable footing to prevent falls during installation. Take your time, especially when working with adhesives, to avoid accidental spills or contact with skin.

How to Install Carpet Treads on High-Gloss Polyurethane Stairs

This project outlines the steps for installing carpet treads on high-gloss polyurethane stairs to improve traction and reduce wear.

Read the full guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Secure Treads to Stairs — How to Install Carpet Treads on High-Gloss Polyurethane Stairs | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.