Locate the Squeak
From How to Fix a Squeaky Floor on a Stair Landing · Step 1 of 5 · Video by Cody Steck

Showing 0:00–0:09 of the source video. Watch the full video with every moment.
What happens in this clip
The initial step involves walking across the problematic flooring to precisely identify and isolate the areas that produce a squeaking sound. By applying pressure with your feet and listening carefully, you can pinpoint the exact locations where the floorboards are rubbing against each other or against the subfloor, causing the unwanted noise.
Goal: Pinpoint the source of the squeak on the flooring.
About the full video
This DIY project provides a simple and effective method to eliminate squeaks in wooden flooring. It involves identifying the problematic areas, locating the underlying subfloor joists, drilling pilot holes, and then using specialized screws that snap off below the surface to secure the floorboards to the joists, effectively stopping the squeaking.
Step 1 of 5: Locate Squeak Source
The first critical step is to accurately identify where the squeak is coming from. This usually involves friction between the floorboards themselves, the floorboards and the subfloor, or the subfloor and the joists. By systematically walking the area and applying pressure, you can often narrow down the source to a specific board or small area. Having a second person can be very helpful to confirm the location from different angles.
Every video in How to Fix a Squeaky Floor on a Stair Landing
Step 1: Locate Squeak Source
- 0:00–0:09 Locate the Squeak (this video)
- 0:55–1:16 Locate and Mark the Squeaky Area
- 0:13–0:20 Locate Squeaky Floor Section
Step 2: Test Lubrication Method
- 0:34–0:54 Apply Dry Lubricant to Eliminate Squeaks
- 0:52–2:39 Apply Powder
- 0:45–0:54 Apply Talcum Powder to Squeaky Area
Step 3: Secure Loose Floorboards
Step 4: Reinforce Subfloor or Joists
- 2:59–4:16 Fix from Below: Use Shims
- 5:35–7:36 Option 1: Shim the Joist
- 0:05–0:10 Insert Shims to Fill Gaps
Step 5: Test and Finish
- 9:40–9:57 Final Check and Confirmation
- 0:23–0:28 Test and Verify Results
- 0:38–0:54 Verify and Clean Up
Questions about How to Fix a Squeaky Floor on a Stair Landing
How difficult is fixing a squeaky stair landing floor for a beginner, and how long should I expect it to take?
This project is rated beginner, but it requires patience to pinpoint the exact squeak source. While the estimated time is 4 hours, it can vary based on how quickly you identify the problem and the chosen solution. Take your time to properly diagnose before applying a fix, as rushing can lead to ineffective repairs.
Can I use nails instead of screws to secure loose floorboards, or are there other fastener options?
While nails can be used, screws like the Everbilt #6 x 3/4 in. Brass Phillips Flat Head Wood Screw are generally preferred for their superior holding power and ability to draw boards tighter, which helps eliminate squeaks more effectively. If you have access from below, small wood shims can be tapped into gaps between the subfloor and joists to eliminate movement without fastening through the finished floor.
What should I do if I fix a squeak, but it returns a few weeks later?
If the squeak returns, the initial fix might not have fully addressed the underlying issue. Re-evaluate the source of the squeak carefully; it might be friction in a slightly different spot or a more significant movement issue between layers. Consider adding more fasteners, using a slightly longer screw if going into a joist, or applying adhesive if the subfloor is moving against the joist.
What are the main safety precautions or common mistakes to avoid when working on a stair landing?
Ensure your footing is secure at all times, especially if working near the edge of the landing. A common mistake is not fully locating the source of the squeak, leading to ineffective repairs – spend time pinpointing it. Also, when drilling or screwing, use a stud finder (DEWALT 3/4 in. Stud Finder DW0100) to avoid hidden wires or pipes, especially if fastening deeply.
Are there any less invasive methods for fixing squeaks if I don't want to drill or use screws?
Yes, for minor squeaks caused by friction between surface floorboards, you can try lubrication methods first. Sprinkle talcum powder, powdered graphite, or even cornstarch into the seams of the floorboards and work it in. This can reduce friction and quiet the squeak without any drilling, serving as a good first step.
What if my stud finder doesn't work well, or I can't accurately locate the joists under the landing?
If your stud finder struggles, try tapping the floor with a hammer; a solid sound often indicates a joist, while a hollow sound suggests open space. You can also look for lines of existing nails or screws in the flooring, which usually follow joists. If you have access to the underside of the landing, that's the most reliable way to locate and mark joist positions.
How to Fix a Squeaky Floor on a Stair Landing
This project outlines the steps to diagnose and fix a squeaky floor on a stair landing. It involves identifying the source of the squeak, which is typically friction between floorboards, subfloor, or joists, and then applying a solution to eliminate the noise. Solutions can range from simple lubrication to more involved fastening.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

