Install Handrail Brackets (Wood Studs)
From How to Find Studs and Set the Right Handrail Height · Step 3 of 5 · Video by Optimum Works Inc.

Showing 1:25–2:44 of the source video. Watch the full video with every moment.
What happens in this clip
Measure the height of your handrail material (e.g., 1 inch as shown). From the chalk line previously marked on the wall, measure down this height and make a light mark. This mark indicates where the top edge of your bracket will align. Using a stud finder, carefully locate the vertical studs within the wall along the handrail's path. Mark the center of each stud where a bracket will be placed. Position a handrail bracket against the wall, aligning its top edge with the mark you made below the chalk line, and centering it over a detected stud. Mark the screw holes of the bracket onto the wall with a pencil. Using an electric drill and a pilot hole drill bit that is 1/8 inch smaller than the diameter of your wood screws/bolts, drill pilot holes at the marked locations. Finally, insert the wood screws or wood bolts through the bracket and into the pilot holes, securing the bracket to the wall. Do not fully tighten the screws yet; allow the bracket to swivel slightly.
Goal: Secure handrail brackets to wall studs for maximum stability
What's used
Tools
- Electric Drill DeWalt
- Handrail Brackets Optimum Works
- Pencil/Marker Unbranded
- Pilot Hole Drill Bit (for wood) Unbranded
- Stud Finder Zircon
- Tape Measure Milwaukee Stud
- Wood Screws/Bolts Unbranded
About the full video
This project provides a step-by-step guide on how to install a handrail on a staircase. The process involves accurately marking the handrail's height and angle, locating wall studs for secure bracket placement, drilling pilot holes, and then fastening the brackets and handrail using appropriate screws or bolts. An alternative method for securing brackets using drywall anchors when studs are not accessible is also demonstrated.
Step 3 of 5: Mark Support Bracket Locations
Hold a handrail bracket against the wall at the desired height, ensuring it is centered over a marked stud centerline. Use a pencil to mark the screw hole locations through the bracket onto the wall. For longer runs, use a level to ensure brackets are vertically aligned.
Every video in How to Find Studs and Set the Right Handrail Height
Step 1: Determine Handrail Height
- 0:47–1:58 Mark Handrail Height
- 0:40–1:07 Measure Handrail Height
- 3:48–4:29 Verify Handrail Height for Code Compliance
Step 2: Locate Wall Studs
- 3:11–4:40 Utilize an Electronic Stud Finder and Mount Item
- 0:34–1:16 Locate and Mark Studs with Stud Finder
- 0:04–0:13 Locate Wall Studs
Step 3: Mark Support Bracket Locations
- 1:25–2:44 Install Handrail Brackets (Wood Studs) (this video)
- 2:22–2:54 Mark Screw Locations
- 2:46–3:44 Locate and Mark Studs for Brackets
Step 4: Drill Pilot Holes
- 1:47–2:15 Locate Studs and Drill Pilot Holes
- 0:31–0:38 Drill Pilot Holes
- 8:51–9:40 Pre-Drill Pilot Holes
Step 5: Attach Support Brackets
- 0:23–0:35 Install Handrail Brackets
- 2:28–2:44 Install Brackets and Mount Handrail
- 2:15–2:28 Mount Handrail Brackets
How to Find Studs and Set the Right Handrail Height
This project outlines the steps to locate wall studs and determine the correct height for installing a handrail, ensuring safety and code compliance for stairways and accessible routes.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

