Cut Drywall Openings
From Recessed Staircase Lighting · Step 4 of 8 · Video by Everyday Home Repairs
Showing 4:11–5:24 of the source video. Watch the full video with every moment.
What happens in this clip
Carefully cut the necessary openings in the drywall for accessing wall cavities and installing the ceiling light. First, use a jab saw to cut a rectangular access hole in the wall above the existing switch, following the marked lines. This hole provides access to the top of the wall cavity and the stud for routing wires. Next, use a hole saw (or a jab saw and a template) to cut a circular hole in the ceiling at the marked center point for the new light fixture. Ensure these holes are made carefully to minimize damage and facilitate repair.
Goal: Create access holes in the wall and ceiling for wiring and fixture installation.
What's used
Tools
- Hole Saw
- Jab Saw
- Oscillating multi-tool
- New Work Electrical Box
- Pencil
About the full video
This project details how to install a new ceiling light fixture in a room that lacks an existing light or junction box, and where the wall switch currently controls nearby electrical outlets. The process involves rerouting the outlet's switched power to the new ceiling light, making the outlets always-on, and fishing new electrical wire through walls and ceiling to the desired light location.
Step 4 of 8: Cut Fixture Openings
Using a template provided with the light fixture or by measuring precisely from your markings, trace the outline of the fixture on the wall surface. Carefully cut along the traced line using a drywall saw or oscillating multi-tool. Be precise to ensure a snug fit for the light fixtures. Avoid cutting into existing wiring or plumbing within the walls.
Every video in Recessed Staircase Lighting
Step 1: Plan Lighting Layout
- 0:42–1:17 Mark Recessed Step Light Locations
- 0:00–0:01 Plan and Mark Light Locations
- 0:34–0:49 Mark Light Placement
Step 2: Determine Power Source and Circuit Needs
- 5:24–5:56 Connect to Existing Power
Step 3: Install Wiring
- 4:17–5:10 Run NM Electrical Cable for Lighting
- 1:10–1:28 Install Electrical Wiring
- 16:51–21:10 Run the Wires in the Ceiling
Step 4: Cut Fixture Openings
- 1:37–2:29 Cut Opening for Light Fixture and Drill Wiring Path
- 3:50–4:15 Cut Openings for Fixture Boxes
- 4:11–5:24 Cut Drywall Openings (this video)
Step 5: Install Light Fixtures
- 2:04–3:10 Install Recessed Light Housing
- 4:46–5:24 Install LED Light Fixture
- 0:17–0:23 Install LED Lights into Ceiling
Step 6: Connect Wiring
- 3:29–4:49 Connect Electrical Wires
- 0:28–0:36 Make Wire Connections with Wire Nuts
- 2:18–2:55 Make Wire Connections
Step 7: Test the System
- 3:42–3:55 Test the Light Fixture
- 2:11–2:21 Restore Power and Test
- 2:16–2:20 Power On and Test
Step 8: Install Trim or Covers
- 2:05–2:23 Install Light Bulbs and Trim
- 0:16–0:33 Install Decorative Trim
- 3:57–4:29 Install Trim and Bulb
Questions about Recessed Staircase Lighting
What are the most critical safety precautions I need to take for this electrical project?
Always ensure the power is off at the circuit breaker before starting any electrical work. Use a voltage/circuit tester to confirm wires are dead before touching them. Familiarize yourself with local electrical codes and wear appropriate safety gear, including insulated gloves and eye protection. If you are uncertain about any step, hire a licensed electrician.
What specialized tools are absolutely essential for installing recessed staircase lighting?
Beyond basic tools, you'll need a voltage/circuit tester for safety and a good drill. A fish tape (like the Klein Tools 100 ft. Non-Conductive Fiberglass Fish Tape) is crucial for running wires through finished walls. A specialized auger bit (e.g., DIABLO 1/2 in. x 7-1/2 in. Auger Bit) is recommended for drilling through studs, and a cable stapler helps secure wiring correctly.
How important is the initial planning for light placement, and what's a common mistake to avoid?
Planning the light layout is crucial for achieving even illumination and avoiding glare, especially on stairs. A common mistake is not considering the light beam spread or stair dimensions, resulting in inadequate lighting or harsh hot spots. Use painter's tape or temporary lights to visualize the effect before cutting any holes.
The project is estimated to take '3 days'; what contributes most to that time, and can it be shortened?
The 3-day estimate accounts for careful planning, safely running new wiring, precise hole cutting, fixture installation, and potentially patching or painting. Much of the time is dedicated to ensuring electrical safety and code compliance. While careful work takes time, having all tools and materials ready can prevent delays, but rushing electrical work is never recommended.
Are there any less invasive or easier alternatives to recessed lighting for staircases?
Yes, if cutting into walls for recessed fixtures seems too daunting, consider surface-mount step lights or LED strip lighting. LED strips can be installed under stair nosings or along handrails, offering a softer, diffused light. These options generally require less structural modification but still involve proper electrical connections.
Recessed Staircase Lighting
This project involves planning the layout, safely running electrical wiring, cutting holes in the wall, installing the light fixtures, and connecting them to a power source. It's a moderately complex electrical project that requires careful attention to safety and building codes.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.
Subscribe for exclusive updates
Be the first to know about promotions, new products, and sales.