Test Fit the Straight Skirt Board
From How to Scribe and Cut a Stair Skirt Board to Fit · Step 4 of 5 · Video by Insider Carpentry - Spencer Lewis

Showing 11:24–12:39 of the source video. Watch the full video with every moment.
What happens in this clip
With the skirt board cut according to the measurements and angles, test fit it on the straight wall. It should align perfectly with the pencil line and have tight connections at the top and bottom. The presenter points out that a slight gap (e.g., 1/16th of an inch) above the marked line is acceptable as it allows for minor adjustments and will be covered by the riser. The goal is to ensure consistency along the entire length.
Goal: Verify the accuracy of the cut straight-wall skirt board.
What's used
Tools
- Cut Skirt Board
About the full video
This project guides you through the process of accurately cutting and installing skirt boards on a staircase. It covers preparing the staircase by removing temporary treads, verifying the 'rises and runs' for code compliance, laying out and marking cuts for both straight and open-side skirt boards using specialized techniques and tools like a digital level and a custom jig. The instructions emphasize precision for a professional finish and offer tips for achieving tight connections.
What's said in this clip
be cut at 50 degrees so I've got the board cut now I haven't test fitted it yet so we're going to see how I did normally whenever I cut these this system the way I do it they turn out pretty much perfect every time so I can see down here I'm lined up and then up here I'll just bump that up a little bit so you guys can see that pencil line there we want it to be dropped in place and bottom and top the whole way up you can see that we're following the pencil line I've got a 16th of space right here I intentionally did that just to give me a little bit of margin for air but my Riser will end up covering all that so it's no big deal and then this like I said I wanted this to be three quarters of an inch high and I'm going to cut this off it might be flush with the subfloor it might be up a little bit depending on how I decide to do that shoe rail detail later now we're on our open side which is a lot more complicated cutting this skirt board out basically first we're going to start by doing the exact same process that we just did we're going to cut the skirt board to length and Notch it around get
Automatically transcribed from the source video.
Step 4 of 5: Dry Fit and Adjust
Hold the cut skirt board in place against the stairs and wall. Check for any gaps or areas where the board is binding. If necessary, use a block plane or sandpaper to make minor adjustments to the edges for a perfect fit against the wall and risers.
Every video in How to Scribe and Cut a Stair Skirt Board to Fit
Step 1: Measure and Mark Riser Heights
- 0:00–0:26 Understand Stair Dimensions
- 7:29–11:09 Measure and Determine Cut Angles
- 4:48–7:28 Layout Straight Skirt Board
Step 2: Transfer Stair Profile to Skirt Board
- 0:26–1:49 Layout Skirt Board Profile
- 5:39–9:34 Mark Riser and Tread Cut Lines Using a Jig
- 0:03–0:07 Mark Initial Stair Profile
Step 3: Cut the Skirt Board
- 1:15–2:34 Trace and Cut Skirt Boards
- 2:44–4:14 Cut and Install the Skirt Board
- 19:55–24:58 Cut and Sand Skirt Board
Step 4: Dry Fit and Adjust
- 2:14–2:33 Test Fit and Adjust Skirt Board (Method 1)
- 11:24–12:39 Test Fit the Straight Skirt Board (this video)
- 25:53–26:23 Test Fit the "Open" Skirt Board
Step 5: Install the Skirt Board
- 1:58–2:58 Secure Skirtboard
- 13:28–15:24 Install Skirt Boards
- 3:40–4:14 Install Skirt Boards
How to Scribe and Cut a Stair Skirt Board to Fit
Outline for scribing and cutting a stair skirt board to achieve a snug fit against the wall and risers.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

