powered by

Mark Riser and Tread Cut Lines Using a Jig

From How to Scribe and Cut a Stair Skirt Board to Fit · Step 2 of 5 · Video by Insider Carpentry - Spencer Lewis

Showing 5:39–9:34 of the source video. Watch the full video with every moment.

What happens in this clip

Utilize a custom-made jig, often referred to as 'Dutchman's pants,' which is specifically sized to match the thickness of your riser material (e.g., 1/2-inch plywood). With the skirtboard still temporarily in place, position the jig against each riser and tread intersection. For each intersection, use a torpedo level to ensure the jig is perfectly plumb (vertical) against the riser before marking the vertical cut line, and perfectly level (horizontal) against the tread before marking the horizontal cut line. It's recommended to mark the cut line approximately 1/16th of an inch higher than the actual contact point to account for potential inconsistencies and to ensure a tight fit when adhesive is applied later.

Goal: Precisely mark all necessary cut lines on the skirtboard

What's used

Tools

  • Custom Jig ('Dutchman's Pants') Homemade
  • Pencil
  • Torpedo Level

Materials

  • 1x10 Skirtboard (temporarily installed)

About the full video

This project provides a detailed guide on how to prepare a staircase for skirtboard installation, including removing existing nosing, measuring stair angles with a digital level, marking precise cut lines on the skirtboard using a custom jig, and making accurate miter and horizontal cuts with various saws to create a professional finish.

What's said in this clip

my stair kit some would call this riches or Dutchman's pants you'll see why in a little bit here okay so the next step I need to mark out the spaces on my strip board here these are called Dutchman's pants because they're shaped like a Dutch mums pants or Amish if you're familiar with that some people call them breeches but it's just a simple jig that will slide the skirt board and this needs to match the width of you're right and material is so in this case these kits come with half-inch plywood for the riser this is a half inch jig I always save you can see here it's got SAV written on it and it's always in my stair kit if this board were to be 3/4 inch thick this jig would need to also be 3/4 of an inch thick so to mark the line where I need to cut the mitre for my riser I'm gonna take my jig make sure it's firmly pressed against the riser to by here and then I'm going to pull out my level my trusty torpedo level I'm going to be marking this front side because that's where the front edge of the mitre is gonna be and that's where I want to cut so I'm going to make sure that this correct contact for whatever reason these never seem to be plumb so I'm going to take my level on the back side and I am going to move this until it's plumb I'm going to push this against the riser and I'll take my pencil and Mark that front edge just this process all the way down using my torpedo level get it plumb and then marking that front edge if you listen carefully you can even hear the mariachi music playing in the background from the painters outside so now we've got our plumb line for our riser miters now we need to find the horizontal line for where we're going to cut for our tread I used the same jig can I just go to the back of the treads of the jig is sitting on the backside and mark the bottom here because this is level across then I'll come and do the same thing on the front make these two lines go away you don't have to get crazy precise with this because I like to cut my my make my cut line and actual maybe sixteenth higher than what my actual mark is to ensure that it sits in my adhesive really nice now you'll notice here as I marked my level line look how far out of level this tread was and it actually is that far out of level so I make my level line usually a sixteenth higher than my highest mark that way the whole thing will sit down just fine if you just make one mark and the treads at a level which they always are it'll be screwed up so always make one…

Automatically transcribed from the source video.

Step 2 of 5: Transfer Stair Profile to Skirt Board

Hold a long framing square or a specialized stair scribing tool against the wall and the first riser. Align one edge of the square with the wall and the other with the riser. Slide the square down until its corner meets the pencil mark for the riser height. Use a pencil to trace the profile of the stair onto the skirt board material. Repeat this process for each stair tread and riser.

Open this step in the guide

Every video in How to Scribe and Cut a Stair Skirt Board to Fit

  1. Step 1: Measure and Mark Riser Heights

  2. Step 2: Transfer Stair Profile to Skirt Board

  3. Step 3: Cut the Skirt Board

  4. Step 4: Dry Fit and Adjust

  5. Step 5: Install the Skirt Board

How to Scribe and Cut a Stair Skirt Board to Fit

Outline for scribing and cutting a stair skirt board to achieve a snug fit against the wall and risers.

Read the full guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Mark Riser and Tread Cut Lines Using a Jig — How to Scribe and Cut a Stair Skirt Board to Fit | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.