powered by

Measure and Determine Cut Angles

From How to Scribe and Cut a Stair Skirt Board to Fit · Step 1 of 5 · Video by Insider Carpentry - Spencer Lewis

Showing 7:29–11:09 of the source video. Watch the full video with every moment.

What happens in this clip

After establishing the layout line, measure the skirt board. First, tack a small nail at the base of the layout line, where the skirt board will meet the baseboard detail. Use a tape measure hooked onto this nail and extend it up to the top end of the layout line to get the total length. For the baseboard connection, determine the desired height (e.g., 5 3/4 inches off the subfloor) and mark this point. Additionally, use a digital level to determine the exact angle of the staircase's incline. This angle (e.g., 40 degrees) will be used for the plumb cuts, and its complement (90 - angle, e.g., 50 degrees) will be for the flat cuts. It is useful to sketch a diagram of the skirt board with all measurements and angles for clarity.

Goal: Gather all necessary measurements and angles for cutting the skirt board.

What's used

Tools

  • Digital Level
  • Nail
  • Notebook
  • Pencil
  • Tape Measure

About the full video

This project guides you through the process of accurately cutting and installing skirt boards on a staircase. It covers preparing the staircase by removing temporary treads, verifying the 'rises and runs' for code compliance, laying out and marking cuts for both straight and open-side skirt boards using specialized techniques and tools like a digital level and a custom jig. The instructions emphasize precision for a professional finish and offer tips for achieving tight connections.

What's said in this clip

so what I do is I just take my tape and I move it until it aligns with the skirt board at five and three quarters and I make a plum Mark right there I almost forgot one really important part how do we know what angle to cut our skirt board at the way I do this is I use a digital level it's so easy to use I've done that my entire career some guys uh will use pitch blocks and things like that they'll maybe drop a skirt board in place and then use a level I don't do any of that I think the most efficient way is to use a digital level so when I'm doing this I leave my long level on here I hit my power button on my digital level and then it's going to tell me right here 40 degrees so I know 40 degrees is the angle I need to be making my cuts at all right now I need to start measuring my skirt board so I'm going to take these blocks that I was using get those out of the way and I like to use a nail and just tack that in place that way I can pull a measurement from so down here I'm going to go to this point which is essentially where the top of my skirt board will be cut down Plum and then my baseboard will run into it I want to pull my measurement from that point I'm gonna come and sit up here and essentially I'm not sure how I'm going to finish my shoe Rail and newel post detail right now so for the sake of making this video I'm actually going to leave my skirt board a little bit high and then I'll just cut it down with a multi-tool later but basically what I did to get my measurement I knew I wanted to be high so I take a little block right here which is three quarters of an inch I'm going to line up the corner right there now I'll take my tape measure hook it on my nail on the bottom measure to that corner it's 74 and three quarters so as I'm doing this a lot of times I'm writing things on the wall here I've got 74 and three quarters written down I want to basically draw out a diagram of how this skirt board is going to look I also need to know the measurement from here to here that's four and three quarters I've got that written down also and I know in my head that I want that down there to be five and a quarters inch down on my Plum cut because I want it to match my baseboard height so in real life as I'm working what this ends up being is I just draw the shape of what this skirt board is actually going to look like so that's just a very general shape I'll transfer my measurements I got 74 and three quarters there I got five and a quarter down here I've got…

Automatically transcribed from the source video.

Step 1 of 5: Measure and Mark Riser Heights

Using a tape measure, carefully measure the vertical distance from the nosing of each tread to the corresponding point on the wall. Mark these heights clearly on the wall. These marks will serve as critical reference points for transferring the stair profile to the skirt board.

Open this step in the guide

Every video in How to Scribe and Cut a Stair Skirt Board to Fit

  1. Step 1: Measure and Mark Riser Heights

  2. Step 2: Transfer Stair Profile to Skirt Board

  3. Step 3: Cut the Skirt Board

  4. Step 4: Dry Fit and Adjust

  5. Step 5: Install the Skirt Board

How to Scribe and Cut a Stair Skirt Board to Fit

Outline for scribing and cutting a stair skirt board to achieve a snug fit against the wall and risers.

Read the full guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Measure and Determine Cut Angles — How to Scribe and Cut a Stair Skirt Board to Fit | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.