Layout Straight Skirt Board
From How to Scribe and Cut a Stair Skirt Board to Fit · Step 1 of 5 · Video by Insider Carpentry - Spencer Lewis

Showing 4:48–7:28 of the source video. Watch the full video with every moment.
What happens in this clip
To prepare for cutting the skirt board for the straight wall, you first need to establish a precise layout line. Use a scrap piece of riser material (3/4 inch thick) and a scrap piece of tread material to create a temporary mock-up of a step. Position this mock-up at the bottom of the staircase and then at the top. Place a level (Stabila level is recommended, which is about 2 3/8 inches wide) across the temporary mock-ups to determine the correct angle for the skirt board. Trace this angle with a pencil. The ideal offset between the top of the stair nosing and the top of the skirt board should be 2 3/8 inches. If working with a long skirt board, mark the bottom and top points, then use a chalk line to connect them.
Goal: Establish the layout line for the straight-wall skirt board.
What's used
Tools
- Chalk Line
- Level Stabila
- accurate level
- Pencil
- Scrap Riser Material
- Scrap Tread Material
About the full video
This project guides you through the process of accurately cutting and installing skirt boards on a staircase. It covers preparing the staircase by removing temporary treads, verifying the 'rises and runs' for code compliance, laying out and marking cuts for both straight and open-side skirt boards using specialized techniques and tools like a digital level and a custom jig. The instructions emphasize precision for a professional finish and offer tips for achieving tight connections.
What's said in this clip
really solid so our next step is installing our skirt board we've got to lay out the skirt board cut it fit it and all that good stuff you can already kind of see behind me I've got a line here how do we go about getting that line one of the reasons that it's really important to correct your Rises and runs before you put your skirt your side skirt board in is because it could potentially move things up or down and then you could end up with a gap down here in the corner if your skirt board is too high so we want to be using a 1 by 10 that's what I like to use and we want to have it just right so we've got a nice margin above our nosing on our Treads but we also want to have enough coverage that we're sure that we're not going to end up with a space back here so basically what I start doing is I take a scrap piece of Riser three-quarter thick in a scrap piece of tread which you'll see right here I'll put that in place down here towards the bottom and then as you can see up here I've got the exact same thing towards the top that is going to give me this offset right here now how much should that be basically what I've been doing my entire career is I use my Stabila level which is about two and a half inches I believe two and three eighths and that is the offset that I shoot for from the top of my nosing to the top of the skirt board so for our layout all we're going to do is very carefully put our level across these scrap pieces of nosing that I've got here so you see I'm making contact here and I'm making contact up here that's going to give me the angle that I want and I can start laying this out so from this point I'll just take my pencil mark across the top the whole way up if you're on a really long skirt board like a 16 foot long skirt board I just marked the bottom and mark the top and then I'll chalk a line between the two in this case we got a shorter section so I can mark that the whole way so now I've got the top of the skirt board laid out and I know down here at the base this is actually all going to be Wayne's coating so we're going to be having our skirt board flow right into the baseboard detail so in this case I knew that I wanted this connection with my baseboard to be five and three quarters of an inch off of the subfloor
Automatically transcribed from the source video.
Step 1 of 5: Measure and Mark Riser Heights
Using a tape measure, carefully measure the vertical distance from the nosing of each tread to the corresponding point on the wall. Mark these heights clearly on the wall. These marks will serve as critical reference points for transferring the stair profile to the skirt board.
Every video in How to Scribe and Cut a Stair Skirt Board to Fit
Step 1: Measure and Mark Riser Heights
- 0:00–0:26 Understand Stair Dimensions
- 7:29–11:09 Measure and Determine Cut Angles
- 4:48–7:28 Layout Straight Skirt Board (this video)
Step 2: Transfer Stair Profile to Skirt Board
- 0:26–1:49 Layout Skirt Board Profile
- 5:39–9:34 Mark Riser and Tread Cut Lines Using a Jig
- 0:03–0:07 Mark Initial Stair Profile
Step 3: Cut the Skirt Board
- 1:15–2:34 Trace and Cut Skirt Boards
- 2:44–4:14 Cut and Install the Skirt Board
- 19:55–24:58 Cut and Sand Skirt Board
Step 4: Dry Fit and Adjust
- 2:14–2:33 Test Fit and Adjust Skirt Board (Method 1)
- 11:24–12:39 Test Fit the Straight Skirt Board
- 25:53–26:23 Test Fit the "Open" Skirt Board
Step 5: Install the Skirt Board
- 1:58–2:58 Secure Skirtboard
- 13:28–15:24 Install Skirt Boards
- 3:40–4:14 Install Skirt Boards
How to Scribe and Cut a Stair Skirt Board to Fit
Outline for scribing and cutting a stair skirt board to achieve a snug fit against the wall and risers.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

