Mark the Stringer Board
From How to Lay Out a Stair Stringer with a Framing Square · Step 5 of 6 · Video by The Home Depot

Showing 3:10–3:59 of the source video. Watch the full video with every moment.
What happens in this clip
Begin marking the tread and rise measurements onto the 2x12 board using a framing square. To save time and ensure consistency, attach stair gauges to the framing square to lock in your calculated rise (7 3/4 inches) and run (10 inches) measurements. Position the framing square near one end of the board, aligning the stair gauges with the edge of the board. Use a pencil to trace the outline of the first notch. Continue marking the remaining stringer notches, ensuring that each new notch begins at the point where the previous one ended. After marking all the steps, extend the final lowest tread line to the back edge of the board. This creates a straight edge where the stringer will meet the floor. This is also where you will factor in the thickness of your finished flooring. For example, if your finished stair treads will be 1 inch thick, mark a 1-inch thickness along the bottom of the lowest tread. This marked section will be trimmed off during cutting to ensure the stringer fits correctly and the bottom step has the appropriate height, accommodating the flooring.
Goal: Accurately transfer stair dimensions onto the 2x12 board for cutting.
What's used
Tools
- 2x12 board
- Clamps
- Bar clamps
- Framing square USA
- Milwaukee
- Adjustable T-square
- Pencil
- Fine-tip marker
- Saw horses
- Sturdy workbench
- Stair gauges
About the full video
This project provides step-by-step instructions on how to accurately measure, mark, and cut stair stringers from 2x12 lumber. It covers calculating rise, run, and step count, as well as accounting for finished flooring thickness to ensure code compliance and a solid stair structure.
Step 5 of 6: Mark the Nosing and Final Cut
After marking all the riser and tread lines, you need to account for the nosing, which is the part of the tread that overhangs the riser. Typically, this is about 1 inch. On your last tread mark, measure out the nosing distance (e.g., 1 inch) beyond the last riser line. This will create your nosing line. The final cut at the bottom of the stringer will be determined by this nosing line and the angle of the last tread. This creates the shape of the stringer that will sit flush on the lower subfloor.
Every video in How to Lay Out a Stair Stringer with a Framing Square
Step 1: Determine Total Rise and Run
- 0:15–0:29 Measure Total Rise
- 0:16–1:17 Measure and Calculate Total Rise
- 0:04–0:30 Measure Total Rise
Step 2: Calculate Number of Risers and Treads
- 2:59–6:51 Calculate Number of Risers and Treads
- 0:32–0:54 Calculate Number of Risers
- 8:59–9:54 Calculate Number of Risers and Treads
Step 3: Calculate Riser and Tread Dimensions
- 2:05–2:24 Calculate Individual Riser Height & Tread Depth
- 0:29–1:07 Calculate Rise and Run
- 3:02–4:45 Calculate Rise and Run Dimensions
Step 4: Mark the Stair Stringer with a Framing Square
- 2:53–7:59 Mark the Stringers and Adjust for Treads
- 6:42–8:10 Lay Out the Stringer Using a Framing Square
- 6:59–9:34 Mark the Stair Stringer for Cutting
Step 5: Mark the Nosing and Final Cut
- 3:45–4:47 Correct Straight Stringer Layout
- 8:10–9:35 Mark Top and Bottom Stringer Cuts
- 3:10–3:59 Mark the Stringer Board (this video)
Step 6: Cut the Stair Stringer
- 0:42–0:53 Cut the Stringers
- 15:12–19:27 Cutting the Stair Stringer
- 2:42–3:34 Cut Stair Stringers
How to Lay Out a Stair Stringer with a Framing Square
This project outlines the process of accurately marking and laying out a stair stringer using a framing square, a crucial step for ensuring safe and correctly proportioned stairs.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

