Mark the Stair Stringer for Cutting
From How to Lay Out a Stair Stringer with a Framing Square · Step 4 of 6 · Video by The Fixer

Showing 6:59–9:34 of the source video. Watch the full video with every moment.
What happens in this clip
Now that the individual rise (7.5 inches) and run (9.25 inches) are determined, use a framing square to mark the pattern on a 2x12 board. The framing square has markings to quickly set these dimensions. Hold the square with the rise measurement (7.5 inches) on one edge of the 2x12 and the run measurement (9.25 inches) on the other. Use a pencil to draw the lines. Repeat this process for each step, sliding the square down the board. For the first step (which connects to the ground/pad), ensure that the bottom rise is reduced by the thickness of the finished tread material. The video shows marking three steps on the stringer.
Goal: Accurately mark the rise and run patterns onto the 2x12 lumber for cutting.
What's used
Tools
- 2x12 Lumber
- Framing Square (Speed Square / Rafter Square)
- Pencil Carpenters pencil
About the full video
This project provides detailed instructions on how to design, calculate, mark, cut, and install stair stringers for a deck. It covers essential concepts like rise and run, explains how to factor in finished materials, demonstrates calculation methods, and guides through the physical marking and cutting process using common woodworking tools. The final steps show how to secure the stringers and attach composite treads to complete the staircase.
Step 4 of 6: Mark the Stair Stringer with a Framing Square
Take your stair stringer board (typically a 2x10 or 2x12). Place your framing square on the edge of the board. Align the 'rise' measurement on the tongue of the square with the edge of the board, and align the 'run' measurement on the blade of the square with the edge of the board. Mark this line. This marks your first riser cut. Then, slide the square along the board, keeping the 'rise' measurement at the top edge and the 'run' measurement at the bottom edge, and mark the next riser. Continue this process, stepping the square down the board for each subsequent riser and tread, ensuring your measurements are precise and consistent. The bottom edge of the stringer will have the tread markings, and the top edge will align with the floor joists.
Every video in How to Lay Out a Stair Stringer with a Framing Square
Step 1: Determine Total Rise and Run
- 0:15–0:29 Measure Total Rise
- 0:16–1:17 Measure and Calculate Total Rise
- 0:04–0:30 Measure Total Rise
Step 2: Calculate Number of Risers and Treads
- 2:59–6:51 Calculate Number of Risers and Treads
- 0:32–0:54 Calculate Number of Risers
- 8:59–9:54 Calculate Number of Risers and Treads
Step 3: Calculate Riser and Tread Dimensions
- 2:05–2:24 Calculate Individual Riser Height & Tread Depth
- 0:29–1:07 Calculate Rise and Run
- 3:02–4:45 Calculate Rise and Run Dimensions
Step 4: Mark the Stair Stringer with a Framing Square
- 2:53–7:59 Mark the Stringers and Adjust for Treads
- 6:42–8:10 Lay Out the Stringer Using a Framing Square
- 6:59–9:34 Mark the Stair Stringer for Cutting (this video)
Step 5: Mark the Nosing and Final Cut
- 3:45–4:47 Correct Straight Stringer Layout
- 8:10–9:35 Mark Top and Bottom Stringer Cuts
- 3:10–3:59 Mark the Stringer Board
Step 6: Cut the Stair Stringer
- 0:42–0:53 Cut the Stringers
- 15:12–19:27 Cutting the Stair Stringer
- 2:42–3:34 Cut Stair Stringers
How to Lay Out a Stair Stringer with a Framing Square
This project outlines the process of accurately marking and laying out a stair stringer using a framing square, a crucial step for ensuring safe and correctly proportioned stairs.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

