Fix with Heavy-Duty Stair Angle Brackets (Method 2)
From How to Stop a Stair Tread from Creaking and Shifting · Step 4 of 5 · Video by stairbuilding

Showing 4:51–8:26 of the source video. Watch the full video with every moment.
What happens in this clip
For situations requiring significant pulling force, a heavy-duty stair angle bracket is recommended. This bracket is designed to accommodate lag screws, which provide superior holding power. Start by marking the desired position for the bracket under the stair tread, ensuring it's set back about 1/2 inch to 1 inch from the tread's edge to allow for pulling. Pre-drill pilot holes for the lag screws into both the tread and the stringer, making sure the drill bit is slightly smaller than the lag screw's diameter to ensure a tight grip. Position the bracket, then insert and gradually tighten the lag screws using a ratchet (socket wrench). Avoid using an impact wrench, as it can over-tighten and damage the wood. Tighten each screw a little at a time, alternating between them, while visually inspecting the tread on the opposite side to confirm it's being pulled into the dado without dislodging from the other stringer. If the gap is too large (e.g., more than half an inch), this method might not be sufficient, and a full stair rebuild may be necessary.
Goal: Secure severely loose stair treads using heavy-duty brackets and lag screws
What's used
Tools
- Drill Bits
- Drill
- Heavy-duty Stair Angle Bracket OMNIGRIP (visible)
- Custom-fabricated metal plate
- Lag Screws
- Pencil
- Rachet/Socket Wrench
About the full video
This video provides two methods for fixing loose stair treads that have pulled away from their stringer dado. It demonstrates how to use both standard A35 brackets and heavy-duty stair angle brackets to pull the tread back into place and secure it, emphasizing careful technique to avoid further damage.
Step 4 of 5: Reinforce with Stair Tread Repair Brackets
For persistent creaking or shifting, install stair tread repair brackets. These metal brackets typically screw into the underside of the tread and the front edge of the riser, or into the stringer. Follow the manufacturer's instructions for the specific bracket system you are using. This often involves positioning the bracket, marking screw locations, pre-drilling, and then driving the screws firmly to secure the tread.
Every video in How to Stop a Stair Tread from Creaking and Shifting
Step 1: Inspect the Stair Tread
- 2:21–3:48 Diagnose Creaking Causes
Step 2: Secure Loose Tread Edges
- 6:29–7:31 Drive Screws to Secure Tread to Riser
- 6:13–6:27 Secure Front Treads with Screws
- 5:17–6:11 Fasten New Treads with Screws
Step 3: Address Gaps with Shims and Adhesive
- 6:22–6:49 Apply 5-Minute Wood Adhesive
- 6:40–7:13 Apply Wood Glue (Back Risers)
- 2:05–4:08 Reinforce Risers and Treads with Adhesive and Timber
Step 4: Reinforce with Stair Tread Repair Brackets
- 4:51–8:26 Fix with Heavy-Duty Stair Angle Brackets (Method 2) (this video)
- 0:15–2:32 Fix with A35 Brackets (Method 1)
- 0:33–0:58 Utilize Prefabricated Metal Brackets
Step 5: Fill Screw Holes and Finish
- 0:22–0:30 Fill Screw Holes with Wood Putty
- 1:40–2:44 Prepare Surface by Filling Holes
- 4:25–4:47 Fill Gaps and Nail Holes
How to Stop a Stair Tread from Creaking and Shifting
Outline for a DIY project to fix a creaking and shifting stair tread.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

