Cut the Ladder Feet
From How to Trim Attic Ladder Legs to the Right Length · Step 4 of 4 · Video by Bunnings Warehouse

Showing 6:06–6:39 of the source video. Watch the full video with every moment.
What happens in this clip
Once both sides of the attic ladder frame are securely mounted, it's essential to adjust the length of the ladder feet so they sit flush with the floor. Fully extend the ladder downwards until it reaches the ground. Using a tape measure, carefully determine the exact distance from the bottom rung of the ladder to the floor. This measurement indicates the excess material that needs to be cut off the bottom of the ladder's rails. Transfer this precise measurement to the ladder's metal rails, marking the cut line. With a hacksaw, carefully cut along these marked lines to remove the excess material. Throughout this process, ensure you wear appropriate safety gear, including gloves to protect your hands, safety goggles to shield your eyes from metal shavings, and ear protection from the sawing noise.
Goal: Cut the attic ladder to the correct length so it sits flush on the ground.
What's used
Tools
- Attic ladder Unspecified
- Gloves Unspecified
- Hacksaw Unspecified
- Hearing protection Unspecified
- Pencil Staedtler
- Safety goggles Unspecified
- Saw horses Unspecified
- ensuring stability.
- Tape measure Lufkin 8m
About the full video
This project guides you through the process of framing and installing an attic ladder. It covers measuring and marking the ceiling opening, cutting out plasterboard and existing joists, constructing new timber framing (noggins), temporarily securing the ladder, permanently fixing it in place, cutting the ladder feet to the correct length, and performing final checks to ensure proper operation and squareness.
What's said in this clip
to pre-drill and screw that side as well now that we've got both sides fixed it's time to cut the feet of the ladder to do this I need to measure from the ladder towards the ground and then cut that amount off the bottom step now I need to transfer that measurement from the join down now that I've marked that I need to use a Handa to cut that off make sure when you're using a Handa to wear gloves goggles and Amo now that you've cut that you can put the feet that came with your attic ladder just make sure you still wear your gloves cuz there could be some sharp edges on there I couldn't access these
Automatically transcribed from the source video.
Step 4 of 4: Test Fit the Ladder Legs
Carefully place the attic ladder back into its installed position in the attic opening. Check that the legs now fit the measured height correctly and that the ladder sits level and stable on the floor. Make any minor adjustments if needed.
Every video in How to Trim Attic Ladder Legs to the Right Length
Step 1: Measure Ladder Leg Length
- 0:00–0:36 Assess and Measure Required Cut Length
- 7:46–8:35 Trim the Ladder to Length
- 0:21–1:52 Measure the Attic Opening and Ceiling Height
Step 2: Mark Cutting Lines on Ladder Legs
- 10:35–12:30 Trim Ladder Legs to Length
- 11:00–13:10 Trim Ladder Legs to Proper Length
- 6:26–7:41 Adjust and Cut Ladder Length
Step 3: Cut Attic Ladder Legs
- 6:06–6:39 Cut the Ladder Feet
- 10:35–12:30 Trim Ladder Legs to Length
- 0:48–0:54 Cut and Reattach Second Ladder Leg
Step 4: Test Fit the Ladder Legs
- 4:28–5:38 Final Adjustments and Ladder Sizing
- 6:06–6:39 Cut the Ladder Feet (this video)
- 0:48–0:54 Cut and Reattach Second Ladder Leg
Questions about How to Trim Attic Ladder Legs to the Right Length
What are the most important safety precautions to take when trimming attic ladder legs?
Always wear safety glasses and hearing protection when operating a circular saw. Ensure the ladder is stable and secure before making any cuts, and keep hands clear of the blade path. Work in a well-lit area and be mindful of your footing when working with a ladder.
How can I ensure I cut the ladder legs to the precise length without making them too short?
Measure twice and mark once, using a carpenter square to ensure your cut line is perfectly square. It's often best to cut slightly longer than you think you need, then test fit and trim off small increments until the ladder sits perfectly. Always ensure the ladder is fully extended and on a level surface when measuring.
Do I need a specific type of blade for my circular saw when cutting alloy attic ladder legs?
Yes, for alloy materials, you'll need a metal-cutting blade for your circular saw. A standard wood blade will not work safely or effectively. Ensure the blade is appropriate for the type of alloy and designed for cutting metal to get a clean cut and prevent damage to the blade or ladder.
What is a common mistake beginners make during this project, and how can I avoid it?
A common mistake is assuming both legs need to be the exact same length, especially if your floor isn't perfectly level. To avoid this, measure each leg independently from its pivot point to the floor, or test fit the ladder and mark each leg individually while the ladder is under slight load. Uneven cuts are also common, so use your carpenter square to guide your saw.
What if my garage or attic floor isn't perfectly level? How does that affect cutting the ladder legs?
If your floor isn't level, measuring each leg independently is crucial. Extend the ladder fully, then mark where each leg touches the floor. You might find one leg needs to be slightly longer or shorter than the other to ensure all feet make full, flat contact with the floor, preventing wobbling.
After cutting, my attic ladder still feels wobbly. What should I check?
First, ensure all four feet are making solid, flat contact with the floor. Check your cuts again to ensure they are perfectly square and not angled. If one leg is still slightly too long or too short, or if the floor is very uneven, you may need to make very small adjustments to one or more legs. Sometimes, slight variations in the ladder's hinge mechanism can also contribute, so check those connections.
How to Trim Attic Ladder Legs to the Right Length
This project outlines the process of trimming attic ladder legs to ensure a proper fit and secure installation. It involves measuring, marking, cutting, and testing the ladder legs for the correct length.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

