Install Base Posts

What happens in this clip

With the post positions marked, proceed to install the vertical balustrade posts. This typically involves drilling pilot holes into the mounting surface at each marked location. Depending on the surface material (e.g., concrete, wood), appropriate drill bits and anchor bolts or screws will be used. Secure each post firmly to the surface, ensuring it is plumb (perfectly vertical) and aligned correctly with the other posts before fully tightening the fasteners.

Goal: Securely attach the vertical balustrade posts to the mounting surface

What's used

Tools

• Anchor Bolts or Fasteners
• Through bolts
• Concrete anchors
• Balustrade Posts Balustrade Superstore
• Wood posts
• Drill Bits
• Wood drill bits
• matched to the type of fastener and surface.
• Drill
• Cordless drill
• Level
• Safety Glasses
• Wrenches or Sockets

About the full video

The video showcases a completed 'Post & Rail Balustrade' glass railing system, highlighting its aesthetic appeal and structural components. Although the video does not provide explicit step-by-step installation instructions, it implicitly demonstrates the finished result of what would be a DIY project. This analysis provides a generalized, inferred sequence of steps for installing such a modular glass balustrade system, drawing upon common practices for similar installations as the video itself lacks granular detail on the assembly process.

Step 2 of 11: Drill Post Mounting Holes

Using a drill and an appropriately sized drill bit, create pilot holes at each marked post location. The size of the drill bit should correspond to the screws or bolts that will be used for mounting the posts. If mounting to wood, pre-drilling prevents splitting. If mounting to concrete or masonry, use a masonry bit and appropriate anchors. Ensure the holes are drilled straight and to the correct depth.

Open this step in the guide

Every video in Cable Railing Installation

1. Step 1: Layout Post Locations

   • 6:04–7:34 Install Stair Posts
   • 0:34–0:52 Determine Post Positions
   • 0:09–0:56 Plan Post Placement and Gather Tools

2. Step 2: Drill Post Mounting Holes

   • 0:41–1:07 Pre-drill Mounting Holes
   • 1:54–2:34 Pre-drill Post Mount Holes
   • 0:05–0:09 Install Base Posts (this video)

3. Step 3: Attach Railing Posts

   • 6:04–7:34 Install Stair Posts
   • 2:06–2:45 Install Railing Posts on Stairs
   • 3:04–3:39 Mount and Secure Post with Through-Bolts

4. Step 4: Mark Cable Attachment Points

   • 0:10–0:35 Understand Cable Rail Layout and Code
   • 0:47–1:53 Establish Cable Spacing and Drill Pilot Holes
   • 0:21–0:32 Measure, Mark, and Install Eye Straps on Posts

5. Step 5: Install Cable Termination Hardware

   • 3:38–7:37 Install and Tension Cables with Lag Screws
   • 8:19–10:38 Feed and Crimp Cable (Fixed End)

6. Step 6: Cut Cables to Length

   • 2:23–3:38 Cut Cables and Plan Installation Order
   • 0:59–1:19 Cut the Cable
   • 0:53–1:00 Measure, Cut, and Insert Cable

7. Step 7: Attach Cables to Terminals

   • 8:19–10:38 Feed and Crimp Cable (Fixed End)
   • 0:16–0:32 Insert and Anchor Cable on First End
   • 6:21–7:49 Tension and Cut Cables

8. Step 8: Thread Cables Through Posts

   • 3:19–4:10 Thread Cable Railing
   • 0:08–0:09 Thread Cables Through Railing Posts
   • 0:09–0:29 Thread Cables Through Hardware

9. Step 9: Install Tensioners and Tension Cables

   • 1:09–1:18 Final Cable Tensioning
   • 0:44–0:51 Install and Tension Cable Strands
   • 0:29–0:46 Tension the Cables

10. Step 10: Trim Excess Cable

    • 6:43–7:27 Trim Excess Cable and Tighten Nuts
    • 0:24–0:25 Cut Cable Overhang
    • 0:46–0:54 Trim Excess Cable

11. Step 11: Final Inspection and Testing

    • 0:16–0:28 Perform Final Inspection and Safety Check