Thread Cable Railing

What happens in this clip

With all posts installed, it's time to thread the stainless steel cables through the pre-drilled holes in the posts. Each cable has two distinct ends: one is a flat end designed to thread onto the cable railing, and the other has a small raised center. The raised center end will go on the opposite side of the railing, ready for tensioning. Carefully feed each cable through the posts, ensuring it runs smoothly and without kinks. This step prepares the railing for the crucial tensioning process.

Goal: Run all stainless steel cables through the installed posts.

What's used

Tools

• Stainless Steel Cables

About the full video

This video provides a step-by-step guide on how to install a cable railing system using tension systems to create a modern and secure deck railing with unobstructed views. It covers mounting posts, threading and tensioning cables, installing top rails, and adding final touches for a complete deck makeover.

Step 8 of 11: Thread Cables Through Posts

Carefully thread the free end of each cable through the designated holes or fittings on the next posts in line. For stair railings, ensure the cable follows the angle of the stairs smoothly. Avoid kinking or damaging the cable during this process. If the cable is stiff, a cable puller tool might be helpful.

Open this step in the guide

Every video in Cable Railing Installation

1. Step 1: Layout Post Locations

   • 6:04–7:34 Install Stair Posts
   • 0:34–0:52 Determine Post Positions
   • 0:09–0:56 Plan Post Placement and Gather Tools

2. Step 2: Drill Post Mounting Holes

   • 0:41–1:07 Pre-drill Mounting Holes
   • 1:54–2:34 Pre-drill Post Mount Holes
   • 0:05–0:09 Install Base Posts

3. Step 3: Attach Railing Posts

   • 6:04–7:34 Install Stair Posts
   • 2:06–2:45 Install Railing Posts on Stairs
   • 3:04–3:39 Mount and Secure Post with Through-Bolts

4. Step 4: Mark Cable Attachment Points

   • 0:10–0:35 Understand Cable Rail Layout and Code
   • 0:47–1:53 Establish Cable Spacing and Drill Pilot Holes
   • 0:21–0:32 Measure, Mark, and Install Eye Straps on Posts

5. Step 5: Install Cable Termination Hardware

   • 3:38–7:37 Install and Tension Cables with Lag Screws
   • 8:19–10:38 Feed and Crimp Cable (Fixed End)

6. Step 6: Cut Cables to Length

   • 2:23–3:38 Cut Cables and Plan Installation Order
   • 0:59–1:19 Cut the Cable
   • 0:53–1:00 Measure, Cut, and Insert Cable

7. Step 7: Attach Cables to Terminals

   • 8:19–10:38 Feed and Crimp Cable (Fixed End)
   • 0:16–0:32 Insert and Anchor Cable on First End
   • 6:21–7:49 Tension and Cut Cables

8. Step 8: Thread Cables Through Posts

   • 3:19–4:10 Thread Cable Railing (this video)
   • 0:08–0:09 Thread Cables Through Railing Posts
   • 0:09–0:29 Thread Cables Through Hardware

9. Step 9: Install Tensioners and Tension Cables

   • 1:09–1:18 Final Cable Tensioning
   • 0:44–0:51 Install and Tension Cable Strands
   • 0:29–0:46 Tension the Cables

10. Step 10: Trim Excess Cable

    • 6:43–7:27 Trim Excess Cable and Tighten Nuts
    • 0:24–0:25 Cut Cable Overhang
    • 0:46–0:54 Trim Excess Cable

11. Step 11: Final Inspection and Testing

    • 0:16–0:28 Perform Final Inspection and Safety Check