Feed and Crimp Cable (Fixed End)

What happens in this clip

The installation of the cables begins with feeding the 1/8 inch stainless steel braided cable through the pre-drilled holes in the posts. Since the holes are only slightly larger than the cable and may have paint residue, this can be a delicate process. Once the cable is fed through to the fixed end, it is cut to the appropriate length using cable cutters. Then, the end of the cable is inserted into the fixed fitting and secured using a hydraulic crimper. This step requires two sets of hands: one person to hold the cable taut and aligned, and another to operate the crimper.

Step 7 of 11: Attach Cables to Terminals

Feed the cut cable end through the appropriate termination fitting (e.g., a fork terminal, eye terminal, or directly through a post if using tensioners). Secure the cable using the manufacturer's recommended method. For swage fittings, this involves placing the fitting onto the cable end and using a hydraulic swaging tool to permanently crimp it. For other types, follow specific instructions, which might involve set screws or specialized crimps.

Open this step in the guide

Every video in Cable Railing Installation

1. Step 1: Layout Post Locations

   • 6:04–7:34 Install Stair Posts
   • 0:34–0:52 Determine Post Positions
   • 0:09–0:56 Plan Post Placement and Gather Tools

2. Step 2: Drill Post Mounting Holes

   • 0:41–1:07 Pre-drill Mounting Holes
   • 1:54–2:34 Pre-drill Post Mount Holes
   • 0:05–0:09 Install Base Posts

3. Step 3: Attach Railing Posts

   • 6:04–7:34 Install Stair Posts
   • 2:06–2:45 Install Railing Posts on Stairs
   • 3:04–3:39 Mount and Secure Post with Through-Bolts

4. Step 4: Mark Cable Attachment Points

   • 0:10–0:35 Understand Cable Rail Layout and Code
   • 0:47–1:53 Establish Cable Spacing and Drill Pilot Holes
   • 0:21–0:32 Measure, Mark, and Install Eye Straps on Posts

5. Step 5: Install Cable Termination Hardware

   • 3:38–7:37 Install and Tension Cables with Lag Screws
   • 8:19–10:38 Feed and Crimp Cable (Fixed End)

6. Step 6: Cut Cables to Length

   • 2:23–3:38 Cut Cables and Plan Installation Order
   • 0:59–1:19 Cut the Cable
   • 0:53–1:00 Measure, Cut, and Insert Cable

7. Step 7: Attach Cables to Terminals

   • 8:19–10:38 Feed and Crimp Cable (Fixed End) (this video)
   • 0:16–0:32 Insert and Anchor Cable on First End
   • 6:21–7:49 Tension and Cut Cables

8. Step 8: Thread Cables Through Posts

   • 3:19–4:10 Thread Cable Railing
   • 0:08–0:09 Thread Cables Through Railing Posts
   • 0:09–0:29 Thread Cables Through Hardware

9. Step 9: Install Tensioners and Tension Cables

   • 1:09–1:18 Final Cable Tensioning
   • 0:44–0:51 Install and Tension Cable Strands
   • 0:29–0:46 Tension the Cables

10. Step 10: Trim Excess Cable

    • 6:43–7:27 Trim Excess Cable and Tighten Nuts
    • 0:24–0:25 Cut Cable Overhang
    • 0:46–0:54 Trim Excess Cable

11. Step 11: Final Inspection and Testing

    • 0:16–0:28 Perform Final Inspection and Safety Check