powered by

Another Simple Solution To A Common Problem Created By Stair Builders - Deck Nosing Or No Nosing

Video by stairbuilding · 3 moments used in Oak Valley Designs's DIY guides · 4:14 long

Moments in this video

  1. 0:37–1:59 Analyzing Stairway Without Step Nosings (Deck Nosing Present) From How to Check Your Stairs Against Building Code, Step 5: Inspect Tread Nosing

    This step analyzes a stairway design where the individual steps lack a nosing (overhang), but the upper deck, to which the top step connects, has a 1-inch overhang. The presenter clarifies that, according to building codes, the tread measurement for the top step is taken from the farthest protruding section of the deck (including its 1-inch overhang) to the farthest projecting point of the step below. This means that despite the physical step being 11 inches deep, the code-compliant measurement becomes 10 inches for that top step. This creates an inconsistency with the other steps, which have a full 11-inch tread. The presenter notes that this specific scenario (deck having a nosing but steps not) is rare and that most building inspectors might not even catch this subtle discrepancy. He suggests a simple fix for this specific problem: remove the deck board, rip (cut) off the 1-inch overhang, and reinstall it to eliminate the nosing on the deck.

  2. 2:00–2:24 Analyzing Stairway with Consistent Nosings (Correct Design) From How to Check Your Stairs Against Building Code, Step 2: Measure Stair Run

    This step demonstrates a correctly designed stairway where all steps, including the connection to the upper deck, uniformly feature a 1-inch nosing. Each tread depth is consistently 11 inches, measured from the front of the nosing on one step to the front of the nosing on the step below. This design adheres to building codes for consistent tread depth, ensuring safety and compliance.

  3. 2:00–2:24 Analyzing Stairway with Consistent Nosings (Correct Design) From How to Check Your Stairs Against Building Code, Step 5: Inspect Tread Nosing

    This step demonstrates a correctly designed stairway where all steps, including the connection to the upper deck, uniformly feature a 1-inch nosing. Each tread depth is consistently 11 inches, measured from the front of the nosing on one step to the front of the nosing on the step below. This design adheres to building codes for consistent tread depth, ensuring safety and compliance.

The guide that use this video

Transcript

0:03 in this video i will provide you with four different stairways two of them will be fine the other two will have a problem and of course this problem is usually going to be provided to you compliments of the stair builder and this seems to be a common problem i've seen it numerous times and is it going to provide you with a unsafe stairway i doubt it but once you're aware of it you can make the necessary adjustments and compensate somehow so that it doesn't happen at least it doesn't happen on any of your projects so for example this stairway here does not have any tread variations each one of these steps is 11 inches and each one of these steps does not

0:49 have a nosing however that's not the case here the upper deck actually has a one inch overhang now this is something you're probably rarely going to run into most of the time the steps will have a nosing on them but the deck won't however i thought i would provide you with this example anyway now for those of you who are not familiar with building codes the building code measurements for a step or the depth of a step will be measured from the upper farthest protruding section of the step to the farthest projecting point on the step below so even though we have an 11 inch wide step here your building inspector and the building codes for something like this is going to count

1:35 this as 10 inches and is something like this going to be the end of the world no i doubt if most i don't want to say all but i doubt if most building inspectors are even going to catch it except of course for those watching this video and the good news for something like this is this is an easy fix you simply pop this board off rip it down reinstall it and you are done now here's another stairway you are not going to have a problem with this one here has the one inch nosing all the way down so we have 11 inches off of the front of the nosing on the lower step to the front of the nosing on the upper step and of course the rest of these steps are the same size so this one here is going to be

2:20 fine and this is what you would be shooting for if you were going to put a nosing on each step and of course this is what originally inspired me to make the video and of course this would probably be the most common problem or mistake made by either the stair builder or the deck builder and of course it provides us with a one inch longer tread now something i need to point out i know some of you people are going to get a little creative while you're watching this video is that i wouldn't suggest to reduce the size of this by cutting an inch off of the stringer and reducing the size of this step by one inch and even though that might be accepted by your local building department it could create problems for the people who use the stairway you start walking up a set of stairs with a

3:06 nosing and you come to a step that's going to be an inch shorter and no nosing up here you could actually create a trip hazard so i think if it was me i would suggest to either use the nosing throughout the entire stairway or no nosing throughout the entire stairway so just keep in mind that sometimes because it might work with your local building department or be within the means of an acceptable building code it might not produce a safe stairway so just kind of throwing that out there so that is it for this video here i gave you four examples and of course ended with the most common problem that you're going to see when building a stairway with a nosing and a deck without a nosing so let us know what you think hit the thumbs up button if you like the video

3:53 comments questions leave them in the comment area and i will answer them as soon as possible

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Another Simple Solution To A Common Problem Created By Stair Builders - Deck Nosing Or No Nosing — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.