Repeat Stenciling for Subsequent Risers
From Stair Riser Wallpaper · Step 2 of 6 · Video by Royal Design Studio Stencils
Showing 0:17–0:40 of the source video. Watch the full video with every moment.
What happens in this clip
After completing the first stenciled section, carefully remove the painter's tape and lift the stencil. If necessary to fit the width or height of a particular riser, you can cut the stencil using scissors. To continue the pattern seamlessly on the next section or adjacent riser, utilize the built-in registration marks on the stencil for precise alignment. Secure the repositioned stencil with painter's tape, off-load excess paint from your stencil brush, and repeat the paint application process as described in the previous step. Continue these steps for each stair riser until all desired areas are stenciled.
Goal: Systematically apply the stencil design to all stair risers
What's used
Tools
- Painter's Tape ScotchBlue
- Scissors
- Craft knife
- Stencil Brush
- Stencil Royal Design Studio Stencils
Materials
- Acrylic Paint Behr
About the full video
This project provides a creative guide on how to update and personalize stair risers by applying a patterned stencil design. It involves carefully preparing the risers, positioning and securing a stencil, applying paint with a specific technique to prevent bleeding, and systematically repeating the process for each riser, using registration marks for seamless pattern continuation.
Step 2 of 6: Measure and Cut Wallpaper/Stencil Material
Measure the height and width of each stair riser. Add approximately 1-2 inches to each measurement for trimming. Transfer these dimensions to the back of the peel-and-stick wallpaper or to your stencil material, and cut precisely using a sharp utility knife or scissors.
Every video in Stair Riser Wallpaper
Step 1: Clean Stair Risers
- 0:48–0:56 Clean Staircase Surface
- 0:36–0:41 Clean and Smooth Stairs
- 0:18–0:31 Clean the Stairs
Step 2: Measure and Cut Wallpaper/Stencil Material
- 2:55–3:51 Measure and Cut Wallpaper for Risers
- 0:15–0:18 Measure Risers
- 0:17–0:40 Repeat Stenciling for Subsequent Risers (this video)
Step 3: Apply Peel-and-Stick Wallpaper
- 0:05–0:14 Apply Patterned Decals/Wallpaper to Risers
- 0:03–0:10 Apply and Smooth the Wallpaper
- 4:19–5:01 Apply Wallpaper and Smooth
Step 4: Stencil Application (if applicable)
- 0:16–0:24 Stencil Decorative Patterns
- 0:33–0:53 Apply Subsequent Stencil Colors
- 1:22–1:26 Affix Stencils to Staircase
Step 5: Paint Application (if stenciling)
- 0:04–0:07 Apply Paint Through Stencil
- 0:04–0:05 Apply Paint to Stencil
- 2:09–2:38 Paint the Top Stencil
Step 6: Allow for Drying and Curing
- 0:08–0:10 Allow for Final Drying and Curing
- 6:08–6:34 Allow First Coat to Dry and Prepare for Final Coat
- 0:11–0:15 Inspect and Allow to Dry
Questions about Stair Riser Wallpaper
How difficult is this stair riser project, and how long should I expect it to take?
This project is rated as 'beginner' difficulty, making it suitable for those new to DIY. The estimated time for completion is around 8 hours, but this can vary based on your staircase size and whether you choose wallpaper or stenciling. Allow extra time for thorough cleaning and precise measurements.
What's the best way to prepare my stair risers before applying wallpaper or stencils?
Thorough cleaning is crucial for good adhesion and a smooth finish. Use products like CROCODILE CLOTH All-Purpose Cleaner Pre-Moistened Heavy-Duty Wet Cloths or Method 28 oz. All-Purpose Cleaner Lime Sea Salt with an All Purpose Sponge. Ensure the risers are completely dry, free of dust, and smooth before proceeding.
What are common mistakes to avoid when applying peel-and-stick wallpaper to stair risers?
A common mistake is rushing, which can lead to bubbles or crooked application. Measure each riser precisely and use a cutting mat, box cutter, and Anvil Straight Scissors for clean cuts. Use an Ettore All-Purpose Acrylic Squeegee to smooth out the wallpaper as you apply it, working from the center outwards to prevent air bubbles.
If I choose to stencil, how can I prevent paint from bleeding under the Stencil1 Leaves Stencil?
To prevent paint bleed, ensure your stencil is firmly adhered to the riser using painter's tape. Apply paint in very thin coats using a dabbing motion with a stencil brush, rather than brushing. Multiple light coats are better than one thick coat, allowing each layer to dry slightly before applying the next.
What essential tools do I need for this project, and are there any I can skip?
Essential tools include a measuring tape, a box cutter or retractable utility knife, and scissors for precise cuts. An Ettore All-Purpose Acrylic Squeegee is highly recommended for smoothing wallpaper, and a cutting mat protects your surfaces. While you might improvise, these tools ensure a cleaner, more professional result.
How do I maintain and clean my wallpapered or stenciled stair risers without causing damage?
For wallpapered risers, gently wipe them with a damp cloth and mild soap, avoiding abrasive cleaners. Stenciled risers, once fully cured, can also be cleaned similarly. Avoid harsh chemicals or excessive scrubbing, which could lift the wallpaper or damage the painted stencil design.
Stair Riser Wallpaper
This project involves applying peel-and-stick wallpaper or stencil designs to the risers of a staircase to enhance its aesthetic appeal.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.
Subscribe for exclusive updates
Be the first to know about promotions, new products, and sales.