Start to Finish Skirt Board Cutting Guide: How to Get Professional Results
Video by Insider Carpentry - Spencer Lewis · 5 moments used in Oak Valley Designs's DIY guides · 26:41 long

Moments in this video
- 4:48–7:28 Layout Straight Skirt Board
From How to Scribe and Cut a Stair Skirt Board to Fit, Step 1: Measure and Mark Riser Heights
To prepare for cutting the skirt board for the straight wall, you first need to establish a precise layout line. Use a scrap piece of riser material (3/4 inch thick) and a scrap piece of tread material to create a temporary mock-up of a step. Position this mock-up at the bottom of the staircase and then at the top. Place a level (Stabila level is recommended, which is about 2 3/8 inches wide) across the temporary mock-ups to determine the correct angle for the skirt board. Trace this angle with a pencil. The ideal offset between the top of the stair nosing and the top of the skirt board should be 2 3/8 inches. If working with a long skirt board, mark the bottom and top points, then use a chalk line to connect them.
- 7:29–11:09 Measure and Determine Cut Angles
From How to Scribe and Cut a Stair Skirt Board to Fit, Step 1: Measure and Mark Riser Heights
After establishing the layout line, measure the skirt board. First, tack a small nail at the base of the layout line, where the skirt board will meet the baseboard detail. Use a tape measure hooked onto this nail and extend it up to the top end of the layout line to get the total length. For the baseboard connection, determine the desired height (e.g., 5 3/4 inches off the subfloor) and mark this point. Additionally, use a digital level to determine the exact angle of the staircase's incline. This angle (e.g., 40 degrees) will be used for the plumb cuts, and its complement (90 - angle, e.g., 50 degrees) will be for the flat cuts. It is useful to sketch a diagram of the skirt board with all measurements and angles for clarity.
- 11:24–12:39 Test Fit the Straight Skirt Board
From How to Scribe and Cut a Stair Skirt Board to Fit, Step 4: Dry Fit and Adjust
With the skirt board cut according to the measurements and angles, test fit it on the straight wall. It should align perfectly with the pencil line and have tight connections at the top and bottom. The presenter points out that a slight gap (e.g., 1/16th of an inch) above the marked line is acceptable as it allows for minor adjustments and will be covered by the riser. The goal is to ensure consistency along the entire length.
- 19:55–24:58 Cut and Sand Skirt Board
From How to Scribe and Cut a Stair Skirt Board to Fit, Step 3: Cut the Skirt Board
With all lines marked, it's time to cut the skirt board. First, match the pencil lines for the main angle with the miter saw. The presenter recommends angling the cut a few degrees (3-5 degrees) out of plumb (not a perfect 90-degree vertical cut) to create a better connection and allow for more space for adhesive. This slight angle ensures a tighter fit and a stronger bond. After making the initial angled cuts, use a jigsaw to cut out the smaller triangular pieces within the notched areas, following the marked lines. Finally, sand all edges smooth before installation to prepare them for finishing.
- 25:53–26:23 Test Fit the "Open" Skirt Board
From How to Scribe and Cut a Stair Skirt Board to Fit, Step 4: Dry Fit and Adjust
After cutting and sanding, test fit the open-side skirt board. The cuts should align perfectly with the treads and risers, creating a tight and professional-looking connection. The presenter emphasizes that an angled cut (a few degrees out of plumb) allows for space to apply PL Premium adhesive, ensuring a strong bond, while still maintaining a tight appearance on the visible front edge. This method prevents gaps and ensures the skirt board remains securely in place.
The guide that use this video
Transcript
0:02 hey what's up guys welcome back we're here at our gated community build getting into some stair building stairs are one of the most intimidating things that a lot of Carpenters go up against but it's really not all that difficult here I'm getting started I've got a two levels of staircases to do I've kind of got the first one done here as you see and I'm going to be taking you guys through the process on what I'm doing up here above we're going to have a white oak staircase with an over the post handrail and a really unique Riser feature on this staircase the risers are actually going to extend past the skirt board a quarter inch very unique detail I'm going to show you how to cut these skirt boards and I got lots of tricks and techniques to share along the way with this process hope you enjoy the
0:49 video Let's dig right in just for a little context this uh we're on the final push of this house you guys have actually already seen this house a little bit we built our library over here but trim racks getting more empty basically just have to do the staircase and some wainscoting we got a mess on the job site lots of sawdust everywhere but just to show you foyer here here and then here we shot a lot of content on these bookshelves so the painters have removed all the shelves now and they're going to be getting started on painting those in the basement so big push for me right now of course everyone wants me out of here that way the job can keep moving on so we're trying to go full
1:35 tilt on this staircase we're going to start off by cutting our skirt boards I'm going to show you how to do that in a second basically on this side obviously the skirt board is a continuous run on this side we've got our skirt board and it's all got to be notched out so how do we do that I've got it all laid out up here and these are just temporary Treads that I put back on that way we could walk up and down but here you see we've got a nice small section that I can do a little demonstration on how to cut these skirt boards so here's a little trade secret for you going back years we used to have a lot of issues with communicating in advance with uh the framer what type of flooring was going to be installed and a
2:21 lot of times they would frame the staircase for carpet which meant that later on I would have to rip all of the framing Treads and risers out and doing that I discovered this little bar right here and it makes the process of tearing out Treads and risers so easy because you can basically hook the treaderizer in between here and use a lot of Leverage so whenever I have to tear out the framing Treads it's really easy just to get in here and you can pop these up really easily so if you do much of this One of These Bars is uh worth its weight in gold it's paid itself off many times now the first thing I want to do before I can install my skirt boards and start laying them
3:08 out I need to double check and make sure all the Rises and runs are correct that the framer actually did it correctly I would say about 90 percent of the time it's not correct so it's something that you basically always need to be checking you need to ensure that each rise meaning each time that you step that it's an equal step up each time if it's not that doesn't meet that won't meet code if it's above I think it's a 3 8 variation that won't meet code and also your runs you need to make sure are also the same here you'll see I've got blocks nailed onto the front of all of my framing stringers that was because
3:53 the framer didn't frame it correctly up here on the top of the Stringer he cut three quarters of an inch off of the back now that is what you would do whenever you're framing a staircase for carpet because in that case the framer would be nailing on a three-quarter inch riser in this case I'm doing that and I also need to nail a riser up here so that pushes everything back three quarters of an inch so I only had an eight and a quarter this is supposed to be nine so on all of these I had to add three quarters of an inch in order to get that corrected so basically all that involves is taking some PL premium and
4:38 smearing it on the on the Stringer and then some finish nails through to nail those blocks on and that'll set up really solid so our next step is installing our skirt board we've got to lay out the skirt board cut it fit it and all that good stuff you can already kind of see behind me I've got a line here how do we go about getting that line one of the reasons that it's really important to correct your Rises and runs before you put your skirt your side skirt board in is because it could potentially move things up or down and then you could end up with a gap down here in the corner if your skirt board is too high so we want to be using a 1
5:24 by 10 that's what I like to use and we want to have it just right so we've got a nice margin above our nosing on our Treads but we also want to have enough coverage that we're sure that we're not going to end up with a space back here so basically what I start doing is I take a scrap piece of Riser three-quarter thick in a scrap piece of tread which you'll see right here I'll put that in place down here towards the bottom and then as you can see up here I've got the exact same thing towards the top that is going to give me this offset right here now how much should that be basically what I've been doing my entire career is I use my Stabila level which is about
6:11 two and a half inches I believe two and three eighths and that is the offset that I shoot for from the top of my nosing to the top of the skirt board so for our layout all we're going to do is very carefully put our level across these scrap pieces of nosing that I've got here so you see I'm making contact here and I'm making contact up here that's going to give me the angle that I want and I can start laying this out so from this point I'll just take my pencil mark across the top the whole way up if you're on a really long skirt board like a 16 foot long skirt board I just marked the bottom and mark the
6:57 top and then I'll chalk a line between the two in this case we got a shorter section so I can mark that the whole way so now I've got the top of the skirt board laid out and I know down here at the base this is actually all going to be Wayne's coating so we're going to be having our skirt board flow right into the baseboard detail so in this case I knew that I wanted this connection with my baseboard to be five and three quarters of an inch off of the subfloor so what I do is I just take my tape and I move it until it aligns with the skirt board at five and three quarters and I make a plum Mark right there I almost forgot one really important
7:43 part how do we know what angle to cut our skirt board at the way I do this is I use a digital level it's so easy to use I've done that my entire career some guys uh will use pitch blocks and things like that they'll maybe drop a skirt board in place and then use a level I don't do any of that I think the most efficient way is to use a digital level so when I'm doing this I leave my long level on here I hit my power button on my digital level and then it's going to tell me right here 40 degrees so I know 40 degrees is the angle I need to be making my cuts at all right now I need to start measuring my skirt board so I'm going to take these blocks that I was using get those
8:30 out of the way and I like to use a nail and just tack that in place that way I can pull a measurement from so down here I'm going to go to this point which is essentially where the top of my skirt board will be cut down Plum and then my baseboard will run into it I want to pull my measurement from that point I'm gonna come and sit up here and essentially I'm not sure how I'm going to finish my shoe Rail and newel post detail right now so for the sake of making this video I'm actually going to leave my skirt board a little bit high and then I'll just cut it down with a multi-tool later but basically what I did to get my
9:16 measurement I knew I wanted to be high so I take a little block right here which is three quarters of an inch I'm going to line up the corner right there now I'll take my tape measure hook it on my nail on the bottom measure to that corner it's 74 and three quarters so as I'm doing this a lot of times I'm writing things on the wall here I've got 74 and three quarters written down I want to basically draw out a diagram of how this skirt board is going to look I also need to know the measurement from here to here that's four and three quarters I've got that written down also and I know in my head that I want that
10:04 down there to be five and a quarters inch down on my Plum cut because I want it to match my baseboard height so in real life as I'm working what this ends up being is I just draw the shape of what this skirt board is actually going to look like so that's just a very general shape I'll transfer my measurements I got 74 and three quarters there I got five and a quarter down here I've got four and three quarters up top right here I don't need to know that I don't need to know that and I don't need to know that I know that my cut is 40 degrees so I'll note that and then I can cut the skirt board and go to town now you might be
10:50 wondering our level gave us 40 degrees what does that actually mean the 40 degrees is going to be your Plum Cuts so this cut will be at 40 degrees and this cut will be at 40 degrees this cut will be I can't remember from geometry it's called either the supplement or the complement but it would be 90 minus 40 equals 50 degrees so the flat cut then will be cut at 50 degrees and this flat cut down here will be cut at 50 degrees so I've got the board cut now I haven't test fitted it yet so we're going to see how I did normally whenever I cut these this system the way I do it they turn out pretty much perfect every time so
11:38 I can see down here I'm lined up and then up here I'll just bump that up a little bit so you guys can see that pencil line there we want it to be dropped in place and bottom and top the whole way up you can see that we're following the pencil line I've got a 16th of space right here I intentionally did that just to give me a little bit of margin for air but my Riser will end up covering all that so it's no big deal and then this like I said I wanted this to be three quarters of an inch high and I'm going to cut this off it might be flush with the subfloor it might be up a little bit depending on how I decide to do that shoe rail detail later now we're on our
12:24 open side which is a lot more complicated cutting this skirt board out basically first we're going to start by doing the exact same process that we just did we're going to cut the skirt board to length and Notch it around get it set in place and then we'll mark the cuts for the for the Rises and runs for our risers and Treads this so basically what you want to do again I'm just taking a scrap of Riser and tread setting it in place and I want to make sure that I've got my 1 by 10 far enough up that I don't end up with a gap right here but at the same time I don't want to be too high up to where I I
13:10 don't have enough space down here here's an example just so you can visually see what I'm talking about we're using a 1 by 10 so this distance right here is crucial I've actually got about eight and three quarters if you go all the way up in there and measure down so in essence if this skirt board was dropped another half inch or three quarters lower I would end up with a space and a gap right here and I wouldn't have enough coverage so the idea here is we want to get this skirt board positioned just in that sweet spot to where we've got a decent amount of margin here going all the way down but we also need to ensure that we've got some margin for
13:57 air so that we don't end up with any gaps right here as you can see here I've already got my line drawn on here the other crucial detail that I want to pay attention to is I want to make sure that this margin underneath my skirt board to the end of the corner bead is nice and consistent the whole way up now because I already have done the skirt board right underneath me I knew that I wanted to have a three and a half inches right here just because that's the way it worked out so what I did is I just started by taking my framing square Mark at three three and a half inches in my little Notch there drew a line same thing on the bottom drew a line and then
14:42 I can take my digital level and I can basically connect those lines and then so here on my putting my level on the line I've got 39.8 and if I bring my level down here on the corner bead I've got 39.8 so I'm matching that reveal uh perfectly consistently so as I did this you'll remember earlier we had 40 degrees on the other side and here I've got 39.8 it's just the kind of the way it worked out usually they're going to be the same it might have been just because of the way the drywall was applied with the corner bead I've got a little bit different angle whatever not a big deal that that's a little bit
15:27 different in this case to me the most important thing here is I want this margin to be perfect along here but if this is off 0.2 degrees versus the other side it's not going to be noticeable by anyone down the road I just went through the same process that we did on the other side so just dropping this one in place here um looks looks good nice down on the bottom I'm even with my pencil line the whole way up I'm just covering it up which is good so now the next step is going to be to Mark where the Rises and runs are and Notch this whole skirt board out now normally if I was installing box noodle posts I would also
16:15 be taking into consideration where the Box noodles are going to be in certain situations I even might install some of the Box noodles before I install skirt boards in this case I'm using a much smaller null post and it's really requiring that all of the Treads and skirts and risers all be finished in advance so I'm not really worried about newel posts at this point on this particular staircase now in order to Mark our risers and Treads we're going to use some people call it the britches method some people call it Dutchman's pants and the reason that was was because going back many years the shape of this jig looked like Dutchman's pants I guess so that's what it's called
17:01 basically all it is you're taking a board you're cutting a little bit more than the thickness of your skirt board out of it so I've got a little bit more than three quarters cut out of this it would even be more ideal if I would have had a piece of plywood and it would be even a little bit taller because then I could have went the full height that I needed to in this case I'm on the job site I got to use what's available so I took a scrap of 1 by 10 and made this cut now what we're going to do with it is essentially be setting it in place over our skirt board and then marking the side for our Riser cut so let me just demonstrate this here so you may want to nail your skirt board in place just with a couple nails to ensure
17:46 that it doesn't move in this case I feel really good this one's locked in here with this kind of birds mouth cut out down here so I'm just going to start dropping this in place I'm going to push it push it firmly in place and then I'm going to make a light pencil line on the back side of this and that's just kind of a starting point because we are going to come back with a level later on and make sure that these are perfectly Plumb because the framer definitely does not cut the stringers out Plum but we're just getting a reference point right now so just moving our way up making a line on the back side at each riser
18:43 now you guys will notice I'm actually marking on the back side of this template in this case that's because our Riser detail on this staircase is going all the way through in the vast majority of the installs I've done we're mitering the Riser into the skirt board and in that case I need to be marking on the front side of my little template here because we want to be mitering it so just make sure that you note that difference in this case we're not mitering we're running the Riser through and that's why I'm marking on the back side of the template now I also need to Mark the underside of where my tread is going to be so that we can make that cut also we're going to use the same method we're going to drop our jig down in
19:29 place so that the whole thing is resting on the top of the Treads and then all I do is make a mark on the bottom as far back as I can and then I'm move it forward and I do the same thing make a mark on the bottom and just work your way up mark push it as far back as I can make a mark for the next step we're going to be needing to make these lines Plum and level unfortunately the framing stringers are often not cut with the risers perfectly Plumb and a lot of times the Treads aren't perfect either so what I like to do is I make a lighter line first when I'm using my template and then I'll go
20:15 back through with my level and I'll make a plum and level line with this guy as you see here now the thing I want to do is I want to find the point on on my previous line that's as far forward and as far up as possible and then I want to plumb down from that with a darker line so that I know which line I'm cutting to as you can see here my lighter line it was about an eighth inch out of Plum so I went from the furthest point forward and plumbed down it's important that you go to the furthest point forward because if you don't and then you go and put your Riser on you'll have a gap right here so we need to make sure
21:02 that when we cut this we're staying just a little bit forward even of what our actual line is same thing whenever you do your Treads so I'm going to look at my two lines I'm going to see which one is higher than the other and I'm going to make a nice level line across there so as you see here I'm just a little bit higher than this line and then this line here I'm about a sixteenth a strong sixteenth higher with my actual line that's important that I get that higher when I make my level Mark that way whenever we make this cut and then put our finished tread down we get a nice tight connection right here so
21:48 everything is all marked uh we're all Plumb and level so now I'm going to take this down to the miter saw and cut everything foreign so the first thing I do is match my pencil lines uh to the angle on the saw I know that I should be around about 39.8 or 40 degrees I'm putting the shadow line of my blade here on my pencil Mark and I'm right at a little under 40 degrees so that's great now the one thing that I do that's very important if you want to get a really crisp result is I don't cut these Square in the sense of vert a vertical cut I cut them a few degrees out of Plum and
22:34 that makes my connections a lot better so here after I've got my miter angle I'm going to move my bevel angle over it can be anywhere from three to five degrees like so so now I'm cutting down into it this way if we go back over here to the staircase I'll show you why that's important we want our risers in our Treads to come together in a way that's really tight so if you come around on the back side here whenever I nail this Riser onto my skirt I want this to be super tight same thing on the underside where my tread is I want that to be super tight so by angling my cut in a few degrees that
23:22 gives me some space to put PL premium and get a nice Bond while at the same time keeping the connection really tight on the back side of these pieces of wood [Laughter]
24:27 foreign [Applause] [Music] now the key thing whenever you're cutting these pieces out you want to make sure that you're not cutting too much you really should not be cutting any of your pencil line off if you're cutting your pencil line off that means you're making your cut too far back and
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

