The Critical Measurements And Codes Behind Basic Stair Construction
Video by gregvancom · 1 moment used in Oak Valley Designs's DIY guides · 23:44 long

Moments in this video
- 17:28–23:43 Identify Landing Size Requirements
From How to Check Your Stairs Against Building Code, Step 10: Evaluate Landing Requirements
The video addresses the specific requirements for stair landings, both at the top, bottom, and any intermediate points of a staircase. For single-family homes, the minimum landing depth and width are generally 3 feet by 3 feet. However, for public buildings or stairs with an occupancy load greater than 50 people, the minimum width of the landing must match the minimum width of the stairway, which is typically 44 inches. The depth of the landing in these cases must also be at least 44 inches. For staircases with a total vertical rise exceeding 12 feet, an intermediate landing is required to break up the flight, regardless of whether it's residential or public. This is a crucial safety feature to prevent long, uninterrupted falls.
The guide that use this video
Transcript
0:02 Here is another question that one of our viewers had and it has something to do with the walk line associated with a stairway. And in most cases, the walk line is going to be 12 in away from one side, usually the inside of the stairway or the path that would be traveled most of the time when going either up or down the stairway. Most people rarely walk up the center of a stairway unless the stairway isn't very wide. So, for example, if I had a stairway that was 26 in wide, I'd probably walk up the center. However, if it's about 5 foot wide, then you're probably going to walk up one side or the other. And most building codes refer to the walk line as something that would be 12 in from the inside of a stairway. So, depending upon what side that would be would depend
0:49 upon the path of travel. And in the walk line, the step measurements, the measurements that you're going to be measuring from the face of the furthest most projecting point on the top step to the furthest point projecting from the lower step or this distance right here most of the time needs to be the same or can vary sometimes. However, the amount of that might not be very much. For example, most building codes allow a 3/8 maximum variation from the shortest to the widest step. So, this doesn't mean you can have a 10-in step here, a 10 and 3/8 in step here, 10 and 3/4 in. No, the steps cannot vary more than 38 of an
1:35 inch. And that might look something like a 10 inch step here, 10 and an eighth inch step here, 10 and a quarter inch step, 10 and 38, 10 and a quarter, 10 and 38, just not more than 38 of an inch. So when we go to the circular stair, we're going to have the same thing. Our walk line is going to be 12 in in. And each one of these measurements need to be the same or whatever your local building codes will allow as variation. So not too difficult. We just went from straight to circular or curved stairs. And of course, the reason why I'm making the video, this was actually the type of stairway that the viewer was questioning. Can you build a stairway where you can flip the treads or flip
2:22 the stairway? For example, if this stairway looks a little similar to the other one, it's because this section right here is the same as this section here. I just rotated it 180° and then snapped it together. And of course, you can see the problem that we're going to have with the walk line to where we're going to have the same size steps here. However, most building codes might not allow you to change at any part in the stairway and go over the maximum distance of 3/8 of an inch for each step. And you can see here where we're probably going from about 13 14 in to about 8 or 9 in. And that also might not be accepted if you alternate each step.
3:09 And I'm just kind of throwing this out there to provide you with a little more things to think about if you're going to get a little creative with your stairway design because something like this is going to provide a different step along the walk line. However, it might not produce a different step if we're going up the center of the stairway. And for those of you who think that I was providing you with a little hope that would allow you to build something like this, think again. This is probably not going to make your building inspector happy. Now, what if we take two sections of a winder, one here, and rotate this one 180°? And even though I'm not suggesting this will be approved by your local building codes, I am suggesting that you could have an argument here
3:54 because this wouldn't be that difficult of a stairway to walk up and down as long as you were kind of traveling this path here and not using the walk line measurements. That would look something like this here. So if we were going to go to the inside and then switch to the other side, if this was allowed, then it might work. However, if our walk line needs to stick to the inside of the stairway, then you can see right here where it's not going to work. And of course, for those of you wondering why you've seen stuff like this built before, then I only have three possible answers. One is that the stairs never went through any type of building permits or building code approval. Two, the building's old and there weren't any building codes when it was built. or
4:41 third on the list is the fact that the building department approved it for whatever reasons. And of course, the biggest problem with building codes is the actual interpretation from your building department representative or inspector or both because sometimes winders are viewed a little different than curves. Even though the only difference in my opinion would be the shape of the inside and the shape of the outside because I haven't found any building codes that suggest that a set of winders cannot connect with another set of winders in the opposite direction even though I've never seen something like this built before. This has got to be one of the biggest problems with understanding the different types of stairways for um private home use
5:27 basically in public buildings. what the difference is and stuff like that. I can tell you what the building code books say. I can tell you what I've learned over the years, but these building codes change and the interpretations of them change. So, you would need to check with your local building department to verify the information in this video. But what I would like to do was point out that there are two different types of stairways. a stairway with a 45 inch minimum tread width, stairway width, and a 11 inch tread depth. And of course, this stairway actually has a minimum or a maximum riser of 7 in, maximum height of 7 in, minimum of 4 in most of the
6:14 time. Over here, we have a maximum of 7 and 3/4 in and a minimum of 4 in again. So we can see we have two different stairways. This one has a three-foot minimum width with 10 inch tread depth minimums. So the minimum tread depth 10 in. This is for a private dwelling. 2018 building code suggests that instead of used to be more or less for a private residential stairway, you could use this right here. So this would be for a single family home R3 construction basically. And this right here is the standard stairway. This is the basic building codes right here. This is
7:00 basically an exception to this building code. According to the building code book 2018, if you have an occupant load less than 50 people, less than 50 people are going to be living in the building, then you can use this right here. More than 50, then you would use this right here. So, you would have to figure out what that occupant load would be. I mean, you go to some restaurants and stuff like that and it'll say occupant load of 68 people. So, I would doubt that you'd be able to use this. If you went to a restaurant, a public building where there are only going the occupant load, maximum occupant load in that building is 40 people, you're probably
7:47 going to have to use this one. Residential homes, this one. Public buildings, this one. And that's probably the best way I could interpret it. And I believe most building authorities would uh agree with that also. So, let's take a look at the residential one. 3- foot wide minimum tread or stair width. This is the entire stairway. If you have build a stairway where you're going to have a section that's going to be larger and smaller, maybe larger at the bottom, smaller at the top, this is going to have to be the minimum for that. Tread depth 10 in. It can be larger than 10 in. Just cannot be smaller than 10 in. The width of the stairway for a public building is 44 in minimum. Can be
8:34 larger, can't be smaller. 11 inch minimum tread depth. And again, that's the distance from the face of the projecting surface. So, if you have a nosing, that would be from nosing to nosing. And again, I got more information on that on some of my other videos. Maybe I'll put some links in here. You can always go to the website, go to the building code section on the website and then go to the stair section in the building code area for more helpful videos or interpretations on this. And some of the videos might be a little outdated also because of the building code book. some of the, you know, I started making these videos in 2008, so some of them might need to be updated, but they should, you
9:21 should be able to look at the data on the video and get an idea whether or not it's still usable. So, anyway, I hope this helps. This is the difference between what I would refer to as a public stairway and a private stairway and the measurements for the treads and risers that you will have to deal with. In this video, I am going to try and explain a problem that seems to be one of the most difficult problems for a stair builder to get or an amateur, someone who's just trying to learn the process. So, let's go ahead and see if we can figure out how many steps you're actually going to need. And way you're going to do that is by dividing the a few numbers into the overall height or the total rise and then working from
10:09 there. So let's go ahead and get started. We have five steps and six risers. Six steps, seven risers, uh seven steps, eight steps, nine steps, and 10 risers. Let's go ahead and take a look at them one at a time. If we divide the uh number 10 into the overall height, which is 42 in for this particular example, that will provide us with a 4.2 in riser height. 10 risers 4.2. And I'm kind of what I'm getting at here is all you need to do is start dividing a few numbers and then work from there. And I'm going to kind of run through that after I do this example here. So, anything less than 4 in 3.82,
10:58 this is below the minimum. 11 risers is going to be too much. So, 10 treads isn't going to work. But 10 treads or 10 risers, nine steps will work. And then if we go to the opposite end, 7 and 3/4 in is going to be the most common maximum riser height. maximum individual riser height per step for most residential stairways. So, this does not include public stairways. And if you're going to be doing some work to a building, wouldn't be a bad idea to contact your local building department, building authorities, and see what your minimums and maximums are. So, all of these numbers in between here that are
11:44 going to be above the minimum and below the maximum will work. So, we can have six risers, seven risers, eight risers, nine risers, and 10 risers for a 42 in or a 42-in tall overall rise. 42 in total rise or height between levels. So, I hope that makes sense. So, the minimum isn't going this isn't going to work because it's going to be too small. This is going to be too tall. You can use any one of these that will work for your particular case. So, let's just go ahead and go through this one here. I believe is the is eight steps. 1 2 3 4 5 6 7 eight steps, nine risers. That's one of
12:31 them. And here, of course, we're going to have seven steps. Six steps. 1 2 3 4 5 six. And then we are going to have five steps. And the five steps will give us a 7 in riser, I believe. Is that what that was? Let's pull up our chart again. Six risers is going to be six 7in risers will give us five steps. So, six 7in risers. Let's pull that down. 1 2 3 4 5 6. Each one of these are going to be 7 in. So, that'll be five steps for that. So if that makes sense, you don't have to watch the rest of the video. However, if it does not and you need one more
13:16 example, I am going to provide you with one. So in this example, we're going to use 75 in for our total rise or the distance between the two floors. That would be the top of the lower level to the top of the upper level. So basically all I'm suggesting here and this isn't that difficult to do is just start dividing numbers into your overall total rise. And I'm going to start with my first attempt here with by using the number seven. And if I do that I divide 7 into 75 I get 10.71. That's too big. Remember, our maximum vertical riser height that we're shooting for is going to be 7 and 3/4 most of the time. Second
14:03 attempt, I'm going to increase this number by two. That's going to bring us to 8.33. We're still too big. So, if I add two more to that and divide 11 into 75, I get 6.82. Now, this is a number we can work with. So, again, I've just divided three numbers and I finally hit one. Now, this I'm not suggesting that you need to stop here unless this number is going to work. So, just divide a few more. 11 worked. I want to see if 10 will. 10 gives us 7.5. And this works also. And 7.5 is is an excellent riser height, by the way. 7.5 with a 10 in tread is a nice comfortable step to use. So, again, you don't have
14:48 to stop there. If we divide 12 into 75, we get 6.25. 25. Now, we have three numbers we can work with here that are pretty good. But again, you don't got to stop there. I'll let you work your way down. But you will see that by the time we get down to using 18 risers, we're getting to 4.17 in. Even though this is acceptable or should be acceptable to most building departments, 19 will not be. You can see here where 19 provides us with a riser height below 4 in. So any of these that have the word good next to it can work for your particular stairway most of the time. So again, you
15:34 need to check with your local building department. And I suggest that strongly. You know, the reason why I say that is because I know a lot of people make videos on YouTube and they say something like it's the it's that's it. There's a that's the law, that's the rule. And that's not the case. You know, you might watch this video if you're living in another country um in Europe somewhere and you're watching this video, it might not apply to you. You you're going to have you're dealing with millimeters and centimeters and stuff like that. You know, you're not dealing with inches. So, check with that. I I really suggest uh doing that to just cover your own uh behind there. And the last thing you want to do is build a stairway and then have someone come up and say, "You got to tear that apart. You didn't build it right." So anyway, let me know if this
16:21 helps. You know that I think one of the most difficult things for a, you know, beginner stair builder to do is figure all of this stuff out. How many steps they're going to need. It's got to be the I can't think of a bigger problem. You know, the next step would be actually getting a stairway to fit in a tight spot. And I do have some videos for that. I will put a link here to um either a playlist or to a video for that. And I will also put a link somewhere in the video cuz I can't have these uh links too close together. But uh check out one of our videos we made on the 17 and 1/2 in rule for stair building. That helps you figure out the tread width. So, I gave you an idea how
17:07 to figure out how many treads to use and how many risers you can use. But the width of the tread, the depth of the tread, that's also important when it comes to uh building a stairway. In this video, I will provide you with a simplified version or explanation from the 2018 International Building Codebook of what's actually required for or to figure out the width and depth of a landing stair landing. Now, the first thing they point out is that a stair landing is at the top and the bottom of the stairway and that it needs to be the same depth as the width of the stairway. So, this is important. There's only going to be one exception to this rule,
17:53 and that's when we get to stairways larger than 48 in wide. So, if you have a single family home, which I would imagine the bulk of the people watching this video are looking for information for their for the homes that they live in or maybe something you're remodeling or building. Now, I need to point out that this information isn't going to be accepted all of us all the time by your local building authorities, your building department. So, if you're building something new or remodeling something, always check with them to make sure that what they require because if they change a little bit, then you know, you could be in for a nightmare. And I also need to point out that there are so many rules and regulations in the
18:39 building codes that some of the people who check the plans don't always check certain things in their mind. They have certain measurements locked in and so they might not be checking it. And these building codes might not have applied to those stairs built in the past, but might apply to the stairs built in the future. So when you go to someone's house and you say, "Wait a minute, this doesn't work here." That's fine. But these building codes from the 2018 International Building Code Book look like they might have changed. So let's go ahead and get started. If you live in a home, single family home or a building with a occupant load of less than 50 people, then uh 36 in by 36 in 3T by 3T
19:25 at the bottom will be a minimum. The stair width is 36 in wide, 36 in deep. And at the top, you would need the same distance, 3T minimum, 3T in depth. It can be bigger, just can't be smaller. Now, these measurements are going to change if you come to a public building or a building with an occupant load of more than 50. And of course, that means that the width, minimum width on a stairway is going to now change to 44 in or 3T8, bringing the depth of the landing to 3'8 in also. So single family homes is probably not going to apply to you, but this will to practically every
20:12 other stairway built. So again, 44 in at the at a landing that's in the stairway by 44 in. And of course, at the bottom, it will be the same also. Now, here's something else that uh can be a little confusing, and I hope I don't make it more confusing, but 4 foot 48 in is kind of a minimum maximum or a maximum minimum for a stairway. And to make it simplify it as simple as I can possibly do it, any stairways wider than 4t wide, any stairways with a width larger than 48 in do not require you to go the uh same depth to use the same measurement as the width of the stairway for your
20:59 landing depth. 4 foot is fine. So it cannot be smaller than 48 in even if the stairway is wider than 4 foot. So if I had a 5- foot wide stairway. I can use a 4ft depth. It does not need to be 5t. I mean if you could imagine this, what if I had a 10-ft stairway? Does it need to be 10t deep? Would I need a 10- foot long, you know, landing? If this was 10 foot wide, no. I could go to a 4ft wide stairway and go all the way up. Now, if you were going to build a stairway that's 10t wide and then come to a landing and have a 10-ft landing with a 10-ft wide stairway, they're not going to have a problem with that because that's going to be well above the
21:46 minimum measurement of 4 foot. So, I hope that makes sense. So, if I had a stairway that was 4'1 in wide, you know, 49 in 4T1, then this could be 4 foot. It does not need to be the same width and depth. They don't need to use the same measurement for that. And of course, that is all the way through the stairway. Another building code you might need to familiarize yourself with will be any stairways with a vertical height longer than 12 ft will need a landing in them. So here we have basically 13 ft 1 1/2 in from the ground to the landing stairway like this will not be acceptable. You will need to have
22:33 a landing in that stairway. So the width of the stairway or the depth needs to be the same or larger than the width of the stairway. Now, I would definitely check with your local building authorities for this one here because I remember and I just kind of just thinking out loud here. This used to be 48 in and it they could have changed it and it might not have ever been 48 in, but uh I would definitely check with them. Now, the reason for this, I think if you've watched some of my videos recently, you would know, is that they if someone was to fall down the stairway, then they're going to fall and stop at the landing. you know, if you fall down from the top of a stairway like this, you could
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

