Installing and Setting Up the Kasa KS230 Smart 3-Way Dimmer Switch
Video by TP-Link Systems Inc. · 1 moment used in Oak Valley Designs's DIY guides · 6:20 long

Moments in this video
- 2:06–2:27 Label All Wires
From How to Wire a 3-way Switch for Stair Lights at the Top and Bottom, Step 3: Identify and label wires
Using the provided wire labels, carefully label each wire in both the main switch box (where the Line wire was found) and the satellite switch box. Label the energized wire as 'Line'. Label any white wires as 'Neutral'. Label any bare copper or green insulated wires as 'Ground'. The remaining wires are your 'Traveler' wires. There should be two traveler wires. Label one 'Traveler 1' and the other 'Traveler 2'. Ensure that the corresponding traveler wires (e.g., the red wire labeled 'Traveler 1' in the main box) are labeled the same in the satellite box. Identify the 'Load' wire in the satellite box, which typically connects to the light fixture itself. This might be the remaining traveler-like wire that is not connected to the main switch's Traveler 1 or Traveler 2.
The guide that use this video
Transcript
0:16 tools that you may need a non-contact voltage tester a phillips and flathead screwdriver and a set of wire nuts you will first want to test the light switches you intend to replace to ensure that the circuit is properly working go to your home's breaker panel and turn off the breaker that controls the light switches you intend to replace you will now want to go to one of the existing switches remove the face plate then unscrew and remove the switch from the wall [Music] using your non-contact voltage tester make sure there is no power going to any of the lines repeat this process for the other switch [Music]
1:14 once you have confirmed there is no power going to the wires remove the two switches from your home's wiring and set them aside for added safety during the next step we recommend putting wire nuts on the exposed wires [Music] return to your breaker panel and turn the breaker that controls the light switch is back on using the non-contact voltage tester test each line until you find the wire that is energized this is your line and where the main switch will need to be installed you will also need a neutral wire present in this box as well if no neutral wire is available the ks230 cannot be installed once the line wire has been located you may return to your home's breaker box and turn the power back off
2:01 using the non-contact voltage tester make sure there is no power going to any of the lines using the provided labels label each wire in the primary box and then in the satellite box label the energized wire as line label the white wire as neutral label the green or copper wire as ground the traveler wires usually one red and one black will need to be labeled the same way in both boxes for example if you label the red wire traveler 1 in box 1 you will need to label it traveler 1 and box 2 as well the screws of the ks230s main unit are color coded and labeled to show where each wire should be connected
2:46 take the wire marked line and connect it to the black screw take the wire marked traveler 2 and connect it to the red screw take the wire marked traveler 1 and connect it to the brass colored screw these wires will need to be joined to the wire clusters marked ground and neutral in the box using the provided screws secure the ks230 unit to the wall as with the main unit the ks230 satellite unit has color-coded screws and labels to indicate where your wires will connect the wires marked traveler 2 and load wire will be connected to the unit with
3:33 the red screw the wiremark traveler 1 will be connected to the unit using the brass colored screw the attached ground wire will need to be joined to the existing wire cluster in the box using the provided screws secure the ks230 unit to the wall return to the breaker panel and turn your power back on you may now return to the ks230s and install their faceplates these faceplates utilize a snap-on mechanism so a firm push is all that is needed to secure them in place [Music] check the main ks230 switch and verify the wireless light is blinking orange
4:19 and green if so you are ready to set up the product using the causa app [Music] look at the main unit and confirm that the wireless light is blinking orange and green if so tap the button to continue go to your mobile devices settings and enter the wireless menu [Music] tap on the ks230s default ssid to connect smart dimmer should be in the name once connected you can return to the kaza app [Music] wait until you are connected to the dimmer from the list choose your home network
5:05 for the dimmer to connect to [Music] type in your network's password then tap on join to connect [Music] wait for the dimmer to connect to your home network [Music] give your smart dimmer a name then tap on save to continue choose an icon for your dimmer then tap on save slowly adjust the brightness of your dimmer to find the minimum level that your bulbs will light up at [Music] now watch why your dimmer brightens from the lowest to the brightest setting this should be smooth without flickering if there was no flickering you may tap
5:52 it's all good to continue if there was flickering you may have an incompatible bolt calibration is now complete you can always readjust the dimming range from the settings menu your dimmer is now configured tap on sounds good to end the setup [Music]
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

