How to install the Safetots Chunky Wooden Screw Fit Gate | Safetots
Video by Safetots · 2 moments used in Oak Valley Designs's DIY guides · 7:04 long

Moments in this video
- 5:13–5:39 Install Gate onto Wall Fittings
From How to Install a Pet Gate at the Bottom of Stairs, Step 4: Attach Gate to Hardware
Carefully take the gate and align the top and bottom spindle bolts on the hinge side with the corresponding hinge side fittings that are already installed on the wall. Gently lower the gate so that the spindle bolts slide into the fittings. The gate should drop into position. Ensure that there is roughly an equal distance between the wall and the nuts on all four spindle bolts. Don't worry about exact precision at this stage, as fine adjustments will be made later.
- 5:13–5:39 Install Gate onto Wall Fittings
From How to Install a Retractable Baby Gate on Stairs, Step 5: Attach the Gate Mechanism
Carefully take the gate and align the top and bottom spindle bolts on the hinge side with the corresponding hinge side fittings that are already installed on the wall. Gently lower the gate so that the spindle bolts slide into the fittings. The gate should drop into position. Ensure that there is roughly an equal distance between the wall and the nuts on all four spindle bolts. Don't worry about exact precision at this stage, as fine adjustments will be made later.
Guides that use this video
Transcript
0:07 the safe touch chunky wooden screw fit stairgate fits from 63.5 centimeters to 105.5 centimeters it comes in five colors a grey a white a black a blue and a natural wood finish when you open the box and the parts box you'll find the following items you have two panels of the gate you'll have four connecting nuts and bolts you'll have the hinge side fittings and you'll have the open inside fittings which will include two restrictors one-way restrictors if you wish to use them you'll also receive a set of templates and a set of screw fittings to enable you to fit the fittings to the wall and we provide screw fittings for
0:52 both plasterboard and wood fittings there's also a small spanner and a set of instructions we also recommend that you have the following tools available to you a spirit level a screwdriver a tape measure and a pair of scissors and or a knife just to open up the gate at the start stage one of the assembly instructions is joining the two wooden panels together first of all we have to measure the space we're going to fit the gate into we're using a gate frame here but you'll be measuring your doorway so for example this one is 75 centimeters wide and if we look at the chart on the instructions to fit between 70.5 and 77.5 you'll be matching up
1:39 holes a and two and holes f and seven if you look at the two panels position the panels as so with the first panel in front of the curve going into the gate the second panel behind with the curve down into the gate and what we do is we just count the holes one two three four five six seven and then on the back a b c d e f g now as i said before our one is a plus two which is two and a at the back and they will correspond with f and seven using the four connecting nuts and bolts we just push them through
2:25 the two panels in each position and secure the nuts and bolts first of all by hand and then using the screwdriver once we've joined the two panels together um we then have to make the decision of which side is going to be opening on the gate and which is going to be the hinge side of the gate and you also need to decide if you want to use the one-way restrictors to stop the gate going past the closed position in one way the way we do these is we take the small plastic pieces here and we can restrict the gate open in either left or right so for the purposes of this demonstration we just slot the small plastic pieces through
3:10 the back on one side if you can envisage the gate will close there but will not be able to go past this point um we're fitting the gate to wooden frames we're going to use the wood screws wood screws could be used against for example banister posts or wooden door frames however if you're drilling into masonry use the raw plugs and the masonry screws that go with the raw plugs the gate comes with two templates a hinge side template these are the hinge side fittings and also the open inside template and you'll see these all match up the pieces that come with the gate so first of all it's really wise to use a spirit level to make sure you're
3:55 completely straight when putting the template in position and then we'll be doing is marking through these holes here and putting these holes into the wall we've already marked up our frame and you'll see that the frame matches the holes that you'll be screwing through and as i say this is the hinge side and that's the open inside the hardware for the gate comes pre-assembled so it's easy to keep it all together there's four different ones the two hinge side ones and the two open inside ones what you need to do is just separate all the pieces to start with and then what you'll be looking to do is first of all add the nut
4:43 quite a way down the uh metal spindle okay next stage of the process is to stick the barrel nut into the gate to help you line it up the long side should be going horizontally you'll be putting the spindle in letting it catch and then just winding it in to start with and you repeat this process on all four corners once we have the hardware in position what we're trying to achieve here is to have roughly equal distance between the wall and the nuts on all four spindles now don't worry too much as we'll be doing fine adjustments later you literally
5:28 take the gate and pop the two into this side and it will drop into position and we want to make sure we're near enough correct on this side which we are these two plastic pieces are very important at this stage you can just lift the gate out of its bracket however as soon as you put these caps into position one at the top and one at the bottom they'll lock the gate in position and the gate will not now be able to come out of the bracket these can be removed when you want to by just slotting a knife in there flicking it open and then that'll enable you to be able to lift the gate off the last stage of the process
6:15 is we do the final adjustment so we just make sure everything is tight first of all on the hinge side and tighten it firmly with the spanner you'll feel it just bite and then just leave it in that position there both top and bottom and then we'll do the final fine adjustments on this side making sure that these both at the top and bottom are tightened up and then tightens up with the spanner and then they'll drop into position over the bracket
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

