powered by

How to Install the Lutron Maestro Motion Sensor Light Switch

Video by Astro Crescent · 2 moments used in Oak Valley Designs's DIY guides · 6:27 long

Moments in this video

  1. 4:51–5:25 Mount Switch and Install Faceplate From How to Install a Motion-Sensor Light Switch in a Stairway, Step 7: Install the Cover Plate

    Once the wiring is complete and neatly tucked into the electrical box, mount the new motion sensor switch using the existing, longer screws that were previously removed. Point out the small tab on the side of the switch that is used for advanced programming. For this installation, the switch will be left in its default settings, and programming details will be covered in a separate video. Finally, install the cover plate, securing it with the appropriate screws.

  2. 5:30–5:53 Test Switch Operation From How to Install a Motion-Sensor Light Switch in a Stairway, Step 8: Restore Power and Test

    Return to the electrical panel and turn the circuit breaker back on to restore power to the circuit. Proceed to the room where the switch was installed. Enter the room to test the motion sensor. The light should automatically turn on upon detecting your presence. Then, leave the room and observe the light; it should automatically turn off after approximately 5 minutes, confirming the successful installation and operation of the switch in its default occupancy mode.

The guide that use this video

Transcript

0:02 Hello friends welcome to my channel in this video I'm going to replace this light switch single pole light switch with a new Neutron occupancy motion sensor light switch I bought this from Amazon for $20 this type of switch is good for garage for kids room for bathroom and for laundry rooms especially in kids room because they usually forget to turn off the light when they leave the room by default the switch is set to Auto on and auto off that means it will automatically turn on when somebody enters the room and the switch senses motion and it will automatically turn off when the person leaves the room and the switch does not sense any Motion in the room that is called the occupancy mode it can also be programmed to

0:49 vacancy mode that means the person will come into the room the switch is turned on and it will automatically turn off when the person leaves the room that is called vacancy mode but by default the switch is programmed for occupancy mode in today's video I will only install the switch and leave it with the default settings so let's get started this is an important caution the procedure shown in this video is for information and education purposes only if you are not comfortable working with electrical wiring or electrical equipment I would strongly suggest that you hire a licensed electrician before undertaking any kind of electrical work always make sure that that you follow your local electrical Safety Code safety first I will go down and turn off the circuit breaker

1:42 first circuit breaker is off I will remove the cover plate and then remove the switch I will use my client tools touchless voltage tester to make sure that there's no power in the switch there's no power so it is safe to proceed there's no power this is an old house built around 50 years ago so I don't see any neutral wire here I only have a white wire and a black wire the switch is not connected to ground but the ground wire is bonded to the box now which one of these is a hot wire and which one is the load I can check that

2:28 but it doesn't matter next I will safely remove these wires this switch is good works fine I will save it and use it somewhere else these screws seem to be longer than the normal so I will have to reuse them because the box is deep inside the drywall this is the DU switch unfortunately it does not come with any installation instructions there's a small slip here and it gives you a QR code scan the QR code to get installation instructions

3:14 and how to program the switch I will have to check that later the switch comes with four wire nuts checking the wires with the switch so in this switch we have two black hot wires they will be connected to these two wires and we have bear ground wire I will connect this wire to the box we have a white neutral wire here with a green sleeve on it and the slip on there's a small tab here which says connect green sleeve wire to ground only in retrofit and replacement applications that means if there is no white wire I can connect the white neutral to the ground started the connections I will connect these two

3:59 wires to the ground inside the box I will use a small pigtail connect this pigtail to the box and then connect all grounds like this this is my ground this ground and this green or white neutral is grounded I will use the wire nut that came with the switch which of these wires is connected to which of these incoming wires in the Box it doesn't matter just make sure that they are firmly

4:45 tight you can also pull the wire and double check that's all about it push the wires inside the box and tighten the screw I will use the same old screws that I removed from the switch earlier if you notice there's a small tab here this tab is used for advanced programming of the switch for now I will leave the switch in its default settings I will cover the settings in a later video so basic installation is done the switch is in its default settings I will now go down and turn the power on

5:33 and check the operation of the switch I'm going to enter the room and let's see if the light turns on or not it's on and here is the switch so the installation is successful very nice so the light just turned off automatically after 5 minutes I will check out the programming Manual of this switch online and then make a separate video on how to program this switch until then I will leave this switch in this default settings that's all for today I hope the video is helpful it is useful if you like the video please give it a thumbs up and don't forget to subscribe to the channel before you leave thanks for watching

6:18 I'll see you next time until then please take care

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

How to Install the Lutron Maestro Motion Sensor Light Switch — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.