How to Force Tread Back into Dado Stringer – Basement Stair Repairs
Video by stairbuilding · 2 moments used in Oak Valley Designs's DIY guides · 8:26 long

Moments in this video
- 0:15–2:32 Fix with A35 Brackets (Method 1)
From How to Stop a Stair Tread from Creaking and Shifting, Step 4: Reinforce with Stair Tread Repair Brackets
The first method involves using a standard metal bracket, such as an A35 angle bracket, and screws. To effectively pull the tread back into the stringer's dado, the bracket must be positioned about 1/2 inch to 1 inch back from the edge of the tread. This creates a leverage point to draw the tread inward. Before installing, inspect the dado for any existing nails or screws that might obstruct the tread's movement; these should be removed if possible. While fastening, carefully monitor the tread's movement. If significant force is required or the tread is severely loose, consider using multiple brackets per tread or on adjacent treads to distribute the pulling force. It is crucial to simultaneously monitor the opposite side of the tread to prevent it from pulling out of the other stringer's dado.
- 4:51–8:26 Fix with Heavy-Duty Stair Angle Brackets (Method 2)
From How to Stop a Stair Tread from Creaking and Shifting, Step 4: Reinforce with Stair Tread Repair Brackets
For situations requiring significant pulling force, a heavy-duty stair angle bracket is recommended. This bracket is designed to accommodate lag screws, which provide superior holding power. Start by marking the desired position for the bracket under the stair tread, ensuring it's set back about 1/2 inch to 1 inch from the tread's edge to allow for pulling. Pre-drill pilot holes for the lag screws into both the tread and the stringer, making sure the drill bit is slightly smaller than the lag screw's diameter to ensure a tight grip. Position the bracket, then insert and gradually tighten the lag screws using a ratchet (socket wrench). Avoid using an impact wrench, as it can over-tighten and damage the wood. Tighten each screw a little at a time, alternating between them, while visually inspecting the tread on the opposite side to confirm it's being pulled into the dado without dislodging from the other stringer. If the gap is too large (e.g., more than half an inch), this method might not be sufficient, and a full stair rebuild may be necessary.
The guide that use this video
Transcript
0:02 in this video I'm going to try and give you at least two different ways you can use to fix a stair tread that has slipped out of the DAT or the slot in the Stringer now the first method I'm suggesting to use would be to use some type of a bracket and some screws and then move the bracket back the bracket is going to need to be moved back remember because the slot uh the DAT or the tread needs to slide back into the slot if you have it at the edge if you have the bracket at the edge you're not going to be able to pull it very you're not going to be able to slide the tread into the slot now I
0:48 would like to point out one more thing there's a good chance that you are going to have something some nails or screws in the slot if you can't remove them you can't remove them at all then um you might need to actually just install a bracket I'm suggesting this if you cannot move the tread if you can't use this method or the second method I'm going to show you then you might actually need to just install some type of a metal bracket here or rebuild the stairway so because it's not uncommon to have nails or screws where someone has either nailed the tread from this side or nailed it from this side and if if the stairway has pulled apart the tread
1:33 has separated from the Stringer you might be able to slide it back in with the nails or screws in place or at least slide it enough to where you can use some brackets here to um make the Treads a little uh safer to walk on where you wouldn't have to worry about it again so this is one method here if you need to use a little more Force then I would suggest using multiple brackets uh might need to even might need to even put more of the brackets on other steps because it's it's uh sometimes it's going to take a lot more
2:19 Force to put this thing back together than it will than it did to have it uh come apart so you could install more brackets up as needed now one thing I would like to suggest would be to install a bracket on the other side this might require a bracket on each tread or multiple brackets on the Treads the reason for this is and this might uh be something that you know you're really not thinking about is that you could actually set this up on this side and start to pull the Treads but the Stringer is not going to move as much and you'll actually pull pull the tread out of the other side you'll pull it out of the slot on the other side so before you do something
3:06 like this make sure that you firmly attach the treads on the other side or at least monitor them as you're screwing or or putting force on this at least monitor them to make sure that you're not pulling them out and that could be done by simply putting a pencil mark on the tread right up against the Stringer and as you're tightening this um make sure that you're actually pulling it together instead of pulling it out so I'm sure that's not that hard to understand if it was me making this type of a repair I would just go ahead and put the brackets on the other side and then monitor the brackets to make sure that I wasn't uh bending anything or putting pressure on it to where the
3:51 brackets would be loosening up or um separating somehow from the Stringer in the tread creating the same problem what we're looking at here is a heavy duty stair angle bracket and I believe you can find these they are called stair angle stair angles you can find them in your search engines or U most Home Improvement centers again carry these now this would be the preferred method of use and the reason why I'm suggesting this and this is only if you need to apply more pressure if the other method I showed earlier using the A35 works then you're going to be fine use those and put put it put put it back together and uh make sure that you
4:37 leave the A35 on after you've tightened everything up there's no need to take these things off um and the same thing would be with the brackets because it's going to help hold everything together now here's a bracket here and this is how it would look underneath the stair step now with these you're going to actually be able to use lag screws and a ratchet a socket and a ratchet I don't recommend drivve using an impact wrench for something like this and I don't have a picture but I'd like to see if I could explain this to you now you could use the same method um as I previously mentioned get the heavyduty stair angle bracket set it back move it back away from the edge of the tread
5:23 about an inch let's say so that you'll be able to pull it into the slot and you might need to put another angle bracket on the next tread up or the next two or three Treads depending upon the type of damage you're dealing with and then firmly attach the bracket to the bottom of the tread and then of course it's going to be at least U um a/ inch to an inch away from the Stringer you're going to use to pull back together then you could use lag screws and you might think about pre-drilling holes into the the stair stringer um you know obviously the holes are going to need to be a little smaller than the lag bolts and then using a ratchet this way you're going to
6:10 be able to slowly pull the um stairway back together and what I would suggest doing would be to tighten this one a little bit and then move to this one tighten it a little bit tighten this one a little bit and see if you're actually pulling the um stairway together but I don't recommend just tightening this one all the way you know make sure that and and then not doing anything here make sure that you tighten them gradually while you are looking at the um slot the Stringer and the stair tread to make sure that you're actually pulling it together I mean it's not going to be um there are going to be times where you're not going to be able to make this type of repair you're not going to be able to
6:56 pull it back together the stairway will need to be rebuilt or you will need to install brackets like these you will need to install a bracket like this underneath your stair step and depending upon the thickness of the tread you might actually need to run bolts and use a carriage bolt to where you have the rounded part on the top run it through here and put a bolt or lag screws depending on the thickness of the stair tread so if you cannot um pull it back together um you can always use a bracket like this that's what these brackets are designed for um to provide you with additional support depending upon how far of a gap you have you know if you have a gap
7:44 where the tread is a half inch away from the stair stringer this might not work the stairway might need to be rebuilt if that's the case but if you have a tread where it's just pulled out of the DAT and and um it's right at the edge here and you can't get it back together something like this would work just fine simply just bolt it back together and uh you should have a safe set of stairs so anyway I hope that helps um and I think I am going to make a few more videos on some of the problems you have with basement stairs at least I'm going to make one more on showing you how to attach the bottom stringers to the concrete
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

