powered by

How To EASILY Add An Outlet In Any Room Using A Light Switch!

Video by How To Home · 1 moment used in Oak Valley Designs's DIY guides · 17:29 long

Moments in this video

  1. 1:42–1:43 Install Light Switch Cover Plate From How to Wire a 3-way Switch for Stair Lights at the Top and Bottom, Step 6: Install switch and fixture covers

    Once all the wires are securely connected to the light switch and tucked neatly into the electrical box, align the light switch and screw it back into the electrical box. Then, replace the light switch cover plate and secure it with its screws.

The guide that use this video

Transcript

0:01 so many times people are wanting to add receptacles or Outlets somewhere in a room but they don't have a convenient place to tap into in order to get power going to that new outlet well in this video I'm going to show you a couple of ways that I go about adding electrical outlets to rooms that don't already have one or are wanting to add one that is more convenient I'm not only going to show you how I go about doing it but I'm also going to go over some huge mistakes that I've seen people do in the past that you really want to avoid because they do create some very dangerous situations and then at the end of the video we'll test out our lights and also our electrical outlet to make sure that they're working independently of each other so let's go ahead and Jump Right In All right so I'm going to show you how easily this can be done by using my mockup wall here now this isn't just a dead wall I actually have power flowing to it so if I turn on this light switch the light comes on and this is the light

0:47 switch we're going to be using I'm going to be demonstrating on in order to show you how I go about doing this in real world applications but in order to get started with this the first thing that we always want to do as is the case with any electrical project is we want to go ahead and make sure that the power is turned off that is going on this circuit and the way that we do that is going to the circuit breaker panel and turning off the circuit breaker that supplies the power to this light switch all right so now that circuit breaker is off a couple of ways that we can go about testing this is we can now go and turn the light switch on and see if the light comes on which it doesn't however the best way to make sure that the power has been turned off is to remove the cover from the light switch and then once that cover has been removed from the light switch I'm go about testing it using either a multimeter or a voltage tester or some people feel comfortable using a non-c contct voltage detector which in

1:34 most cases that will probably work but I would say that it is not necessarily the recommended way of doing it as they sometimes are not fully accurate all right so now that the power is off this is then when you would want to figure out where you want to put your new box in order to install your new receptacle now as you can see I've already got my whole cut out here and it is pretty much right below where the light switch is this is going to be the easiest way of going about doing this because then we don't have to mess with going between stud Bays we don't have to worry about drilling through anything but this will be very easy to figure out where this can go you'd want to take a stud finder and figure out which side of your light switch the stud is on and then you have an idea for where your stud is and then how much room depending on which side as to where then you can put your hole then once you figure out where that stud is

2:20 and where you want your hole to go I typically just take the box put it up against the wall Trace all the way around it and then I take a drywall or jab saw and cut that hole out then once I've got my hole made I'm going to leave it empty and now I'm going to remove my light switch from the box and this will give me more room to work with all right so now it's at this point where I would want to take my new wiring and I want to run my new wiring from my switch boox down to my hole for my new outlet and there are numerous ways that you could go about doing this but one thing I like to do on non-insulated walls when I'm doing this is a lot of times I'll use this this is a chain and I have found this to work incredibly well in numerous instances when I'm pulling new wire into a wall the reason I like using this so much is once I get it through the holes

3:05 in the original box gravity is just going to pull that chain straight down like so and so it's going to be very easy for me to locate it all right so the way that I go about doing this is I take my new wiring I take my chain I overlap my chain onto my wiring probably at least 3 or 4 in and then once I've got that in place and overlapped I then take some electrical tape and I just start wrapping it all the way around the wiring and the chain multiple times all the way up until the end and by wrapping it that much it ensures that when we're going and pulling this in the wall that our chain does not separate from the wiring all right so now that I've got that all set up I'll take the end of my chain here and I'm going to feed it into this box into one of the holes that's in the back now that I can see that chain through that hole I can go ahead and grab it and feed it through the rest of

3:52 the way and then just keep feeding my wire through that hole and eventually we're going to start pulling it through the bottom hole just like that and now at this point I can install my new electrical box now these are not called new electrical boxes these are actually called old work electrical boxes but like always for your convenience I'll have links for this along with all the other materials and tools that you're going to see in this video I'll have links for everything down in the description down below when you click on those links it will take you directly to whatever you clicked on so you can check all this out for yourself so now all I need to do is take my junction box run my wiring down into that junction box and then just pull it out and feed it out to the the front of that box now that I've got that fed through I can now push my box into the wall and then take a screwdriver and then tighten down each

4:37 one of the screws tighten those down until we're getting a good amount of resistance and now our box is installed and firmly in place now as far as this wiring goes I want to make sure that I've got at least 6 in of wiring coming out from the back of the box and extending out to the front and then I also want to make sure that that 6 in is Enough by making sure there's at least 3 in of wiring coming out from the front portion of the box which we have and then I want to do the same thing up here at the top make sure I've got at least 6 in coming out from the back of the box 3 in past the front and then I'm just going to cut it off at that point so now I want to get my protective sheathing removed from my wires here so that they're exposed and I can work with them and I want to make sure that I cut the sheathing off all the way back to the back of the box just after where it enters in and I can very easily do that

5:23 by using the sheathing stripper right here these aren't very expensive and they can really cut down on a lot of time when stripping the sheathing and it also helps to protect and keep those wires safe from accidental Cuts using say a knife for instance all right so now that we've got our wiring running from box to box and we've got our sheathing removed now it's time to start actually hooking things up so the first thing that I want to install and hookup is going to be our new outlet down below all right so the first thing I want to do is make sure that all of my wires are stripped so that I can then connect it to my new receptacle all right so now that the wires are stripped now I need to make some J Hooks so they can wrap around the terminal screws on the receptacle and I can easily do that by using my wire strippers like this so I'll go ahead start with the ground wire wrap it around my green ground screw

6:08 down here at the bottom and we want to make sure that when we wrap it around that screw and any of the screws that they're wrapping around in a clockwise Direction this is going to help promote the wiring being pulled in closer to the center of that screw and make for a very long lasting and good connection and make sure that's down nice and tight next wire I want to connect is my white neutral wire and I'll just again wrap that around that terminal screw in a clockwise Direction and then tighten it down all right so last but certainly not least is our black line wire now on the white neutral wire we put it over here on these silver colored terminal screws for the black line wire or hot wire they go over here on the brass colored screws or they might look gold to you so again I just wrap it around in that clockwise Direction and then tighten it down so

6:54 now I can push all the wiring into the back of the box and screw down this receptacle into that new box but if you're like me and want to get things done as quickly as possible I like to always use my electric screwdriver when I can now one thing that also quickly know is do you see these ears that are on the receptacle since I'm installing this into an old workbox you should snap those off so this receptacle sits down nice and flush and when you put the cover plate on there isn't a gap whereas if I leave these ears on and I put the cover plate on there's going to be a slight gap between the cover plate and the wall so this is not a permanent installation for me so I'm not going to snap those off but I did want to note that because when you use one of these old work boxes like this those ears absolutely need to be snapped off and that can be very easily done just using some needlenose pliers and twisting them

7:40 back and forth and eventually they'll just snap right off and everything will be nice and flush whereas you'd want to leave these ears on if you were installing into a new workbox because those ears are what then go up against the drywall itself and keep that receptacle from being sunken in so then once that receptacle is installed those ears are snapped off if they need to be then I'll just just take my cover plate and then install it and so now the electrical outlet is wired up and installed so now this is where things get very interesting and where I've seen people make some just really bad mistakes and create fire hazard type situations and that's when it comes to then connecting all of these wires to the ones that are existing but before I do anything with wiring anything up here one thing I am going to need to know is

8:26 if I flip this switch over here to the right side I need know which one is the hot wire or bringing the power in and once I figure that out then I'll need to disconnect that wire from this switch and then I'll show you what I'll do with it so the only way to go about doing this and it needs to be done very carefully is I need to go ahead and turn the circuit breaker back on that supplies the power to this light switch now that that circuit breaker is back on I'll just test really quickly to make sure the light comes on which it does so the power is back on going here so this is live so I'm going to take my voltage detector here turn it on I'm going to go ahead take my first probe put it over here on the ground screw over on the left side then I'll take my other probe and I'll touch it to one of these terminal screws on the right side and figure out which one is hot once it touches the wire that's hot this light right here should illuminate all right

9:12 so as you can see here this bottom terminal screw is the one that has the hot wire on it I'll go ahead just for the sake of it and touch the top one and as you can see it's dead now if this was in the on position then you would get 120 volts just like you would in the bottom so you always want to make sure the switch is off that way you know your isolating it and you know that you're getting the correct wire all right so now that I know which terminal screw has the hot wire attached to it I'm going to go ahead turn the circuit breaker back off and now again just make sure that that power is in fact turned off all right so I want to go ahead loosen up that screw where my hot wire is all right so now this is where some people will just make a very big mistake and create a very serious safety hazard I've now loosened up my screw where my hot wire is a lot of people don't know how you should hook this up and a lot of people are just used to like daisy

9:58 chaining and so what some people will do is they'll take their new wiring once they've located where the hot wire is they'll put a J hook on their new wiring so like this and without removing the hot wire that's already around this screw they'll take their new wiring and then they'll also then just take that new wire and stack it on top of the wire that's already there and installed and then they will tighten it down this is not only against code this is also very very dangerous because when you stack those wires even if you tighten this down what you think is enough because those two wires are together over time they can very easily move and when those wires move eventually one is going to slip and then can come loose in the box and if one wire comes loose from that sandwich that was created then the other

10:44 wire is also going to be able to be loose and then just free in a box which could create all kinds of issues whether it's a short circuit or even a fire so never ever ever double stack a terminal screw just so that you can tap into the current that is going to it this is just not the way that this should be done this is completely illegal and unnecessary all right so now what I want to do now that that's all loosened up is I actually want to remove my hot wire from the light switch so let's go ahead and start wiring all this up all right so I'm going to start with my ground wire here well now we need to connect our new ground wire to those other grounds now what we could do is just remove this wire nut and then we could just take our new ground wire Bunch all these up together and then put them back underneath of not this wire nut but get

11:30 a new wire nut and put them all underneath of that one wire nut that is an option since this is a low amperage situation another option that I think is very good for this especially for diyes is to use a Wago connector so the way that these work are you've got these levers on them they just flip up then you can take your wire that you want to connect and then just insert it into that Port where the lever is flipped up flip it over to the bottom you can see clearly that is all the way up to the top here and then once you see that then you can just just flip that lever down and now that wire is connected and we're just going to do the same thing with our remaining ground wires so now just like that and as easy as that all of my ground wires are now connected so now I can push that into the back of the box all right so now all of our ground wires are connected so now we're going to move on to hooking up our white neutral wire

12:17 to our new receptacle and it's kind of the same thing as the grounds you're often times going to have another wire nut and wires in the back of the box they're all bundled together underneath of one wire nut like this so I'll just pull that out so kind of the same thing as we did with the grounds so I'm going to go ahead and remove that wire nut so same exact thing flip up the levers and I'm going to insert each wire one by one and flipping a lever down on each one of those wires as I insert them into this Wago connector so now all my neutrals are connected together so now I'm left with two wires my hot wire here that I took off of the light switch that's supplying the power and my new black wire that's going to my receptacle we need to get power flowing to this wire so that receptacle can be powered but how do we do that and then also attach it to this light switch so the light

13:02 switch can be powered and then to the fixture well this is very easy to do and a lot of people Overlook it and that's by using a pigtail just like is being used with the ground wire on this light switch and in this case I'm going to need one end that's straight and then I've also made a J hook here and the reason I've made a J hook here is because this pigtail is what's going to actually Supply the power to this light switch and then ultimately the light fixture so I need to have a J hook on here so I can attach it to the switch now I'm going to take my new Wago connector with the levers already up I'm just going to insert each one of my black wires that are in this box then flip the lever down on each one of them I personally always like to put my hot wire in the middle of these lever connectors in the middle slot I just feel like maybe it's just in my head it helps distribute the power better and then I'll flip that down and now I'll

13:48 take my pigtail and insert it into that last port flip that lever down and so now as you can see our hot wire which is this one in the middle is now supplying the power to these two new wires this one going onto the receptacle and this one then going to the light switch so now I can push those into the back of the box bring my light switch around flip it over here to the side and now I'll take that J hook on that pig tail that is now connected to the hot wire wrap it around that terminal screw again in a clockwise Direction and then tighten it down all right so now everything is wired up on the switch so now I can push everything to the back tighten down my light switch into the box again and then I can put the switch plate back in on top and just tight down the two screws now before I show you testing out the switch to make sure it's still working and then also testing out

14:35 the new receptacle another option that is available that some people might want to use instead of running all new wiring and installing a new receptacle depending on how you care about looks another option that is out there is this switch receptacle combo right here and I do have a video installing this and testing this already on the channel That I will link at the end of this video so you can see more about it if you would like to and now that that circuit break Breakers back on I'm first going to test out the new outlet I'm going to do that by using this Outlet tester here if everything is wired up properly this green light will light up we'll see that it has 120 volts and we won't see any errors here on the screen so I'll go ahead plug it in and as you can see we're getting that green light and it's showing 121 122 volts so that's perfectly fine right around that 120

15:21 volts and it also says that everything is wired up correctly so now just pull that out now I'll insert it into the top one and as you can see same thing green light 121 122 volts and it says everything is wired up correct so Outlet tester makes it super easy to make sure everything was wired up properly and also gives you some readings as to what you're getting so the new receptacle is working and wired up properly but did we mess up anything within the lights so Moment of Truth here to make sure that our lights are still working independently of our receptacle as you can see I left my outlet tester in that receptacle the green light is on that is showing you that even though the lights are not on the switch is not on that outlet is still receiving power and working properly so all I need to do in order to test the lights is turn on the

16:06 switch and as you can see the light has come on so this is demonstrating that the lights and the receptacle are in fact working independently of each other which ultimately is the goal for this installation and as you saw as I went through everything and pointed some things out that it was relatively easy and quick to do now one thing to just really quickly note is because I get a lot of questions about this on projects like this is is where do I get my materials and tools from and like I mentioned a little bit earlier for your convenience I'll have links for everything you saw in this video from all the materials and tools that I use to make this installation possible I'll have links for everything down in the video's description right down below where when you click on those links it'll take you directly to whatever you

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

How To EASILY Add An Outlet In Any Room Using A Light Switch! — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.