WOOD RAILING on STONE STEPS (Mike Haduck)
Video by Mike Haduck Masonry · 2 moments used in Oak Valley Designs's DIY guides · 16:20 long

Moments in this video
- 12:04–13:20 Install Handrail Cap and Final Brackets
From How to Install a Handrail on Outdoor Concrete Steps, Step 7: Install End Caps or Returns (if applicable)
Position the pre-fabricated handrail cap directly over the assembled top railing section. Ensure it fits snugly and is aligned properly. Secure the handrail cap using appropriate fasteners (e.g., finishing nails or screws) that won't be visible. Finally, attach L-shaped brackets to the top and bottom corners of the railing sections where they meet the existing support posts. Drill pilot holes and secure these brackets with screws, providing robust lateral stability and completing the installation of the railing system.
- 15:21–16:35 Final Inspection and Finishing Touches
From How to Fix a Wobbly Outdoor Stair Railing, Step 5: Test Stability and Finish
Once all railing sections are installed and secured, perform a comprehensive final inspection. Check the stability of all parts, ensuring there is no wobble or movement. Confirm that baluster spacing adheres to code requirements. The presenter jokingly notes that 'a lot of caulking and a lot of paint makes a carpenter what he ain't,' implying that minor imperfections can be concealed for a professional-looking finish. This step ensures the railing is safe, functional, and visually appealing.
Guides that use this video
Transcript
0:06 Well, I built myself some railings for my steps and my stoop here. I'm not a carpenter and I'm far from it, but I know enough from framing houses and doing roofs and odds and ends on houses and basically how to do it in the way I wanted it. Let me show you the way I wanted it. So, this is the way I wanted it. I didn't want any post coming all the way down like this. And I didn't want any post here. So, I made it like a flying thing. And I bolted it here. And I bolted it here on the post that goes up into the roof. And I put my railings on it. And the same thing over here. I bolted everything on. And it's kind of
0:52 flying here. It was easy. I used these clamps right here to bolt it in, but it is solid as a rock and that's the way I wanted it. And when we were coming around over here, we would be bumping into it. So, we kept a little back from the steps and I kept the whole stoop over here. So, it's easy for me to open the door because by code you have to be 36 in. And see all the space I got to walk around here. That's the way I wanted it. So, here we go. I'm going to show you how I did it. Okay, our steps are done and now we got to replace these beams.
1:38 We know that. You can see it's all rotted in here. So, that's a definite. And we got to replace this beam. And we're going to put a railing up in here. Now, this beam is closer than this beam. So, we might move that beam over. And we got to figure out uh our angle on these steps. So, that's the first thing we're going to do. The first thing I'm going to do, which I always learn to lay everything out dry, right even with this, right even with that, draw my line. That's where I'm going to cut
2:26 it. And I got to go with the slope, which this is the slope that goes along the steps. So, I want to be writing with that slope and make my mark right there. So, then I put the two of them together and that's going to be it. That's my slope. Now, I'm going to make four of these. See that? Going to make four of these and cut them all up even. Well, I didn't do the angle 100% right. So, we're going to fudge it a little bit so I could put a steel band in there to hold this together. I'm going to cut this right like that. See, I'm going to
3:12 put this steel band in here like that to hold them together. And up here, too. And I don't want it to be seen. So, first I'm just going to get the screw gun. make my pilot hole and put one of these in just to make sure. Okay. Now, some might disagree with this, but it's all going to be hidden and you're not going to see it. I'm going to put this band on.
4:06 Okay, I got my piece banded together. That's all going to get hidden. Then I chart check my slope and I'm good. Doing this all by myself. Code says uh 34 in to 38 in. So here's 34 and 12. And I'm gonna have a handrail outside. And I'm doing this all by myself. So I'm going to put it up here like this and then screw it in and see where we're at. So now what I did was I got to go every 4 in. 4 8 12 16 20 cuz code says you can't have more
4:52 than 4 in between your slats. So I bought these. These are going to be my slats. And this is going to be my slats. And then I just drill through them like this. pilot hole and then put them in. Well, I'm doing good. The battery went dead. And I want to get the same
5:38 distance. You see this? I'm going to have to do something here to really lock this in. And I have to come over here and get this pole the same distance. So the next thing was up there. I got bolts and we look on this side and we got them bolts. I don't know if you can see them up there. And we're going to loosen them bolts and we're going to move this over to here. All right. Now I'm going to remove this railing. Gonna lay it down on a flat and copy it. Now that I got that all done, all I got to do is match it up same
6:25 way. And I think I'll do it this way so everything everything matches up and copy it except backwards just like that. Okay, I'm following the same pattern as before and I'm putting all these things in just following what's underneath. Then I'm going to install it. Well, this is my two beams right here. And on the bottom right here, I got this plastic composite board I took
7:12 off. I'm going to put that on the bottom for a water shield. And I got to get this plate off the bottom. I'm going to get rid of the nails first and loosen it up. So, I just got a regular house jack and I'm going up there parallel and I'm going to screw a screw up in there in case this jack ever slips. This board won't fall on me and jack it up. Okay, that's good. Now I'll just rightly jack it up. I jacked it up about
7:57 a quarter of an inch. I'm going to cut this plastic piece out for the bottom. Let's see where it fits the best. right there on the bottom. That's good. So, my first decision is to cut off the whole big piece I don't [Applause] need. And this the side of the beam it's going to hold up. And this is the better side. That's the site I'm going to be seeing when I walk down
8:44 the steps. So, I got to cut this part out. I don't have a miter saw and I don't have a table saw, but I do have a sawzaw. I remember when sazal first came out, everybody was going, "Wow, man, these things are Okay. So now all you got to do is get it in on this side of the post. I'm 4 and 1/2 in. I go over here. I got to get this 4 and 1/2 in and move it. Okay, I got that beam
9:31 into place. And then I could uh take this one off and I'm all done. Now I'm drilling my hole to go through. Then I take my bolts, put them through, and I put my washer on and my bolt. Okay, I'm laying it all dry. I got it where I want it. Got my pillar in. I want these slats to be even. I don't want to walk down here and see anything crooked. So, uh, laid it out dry. It's one of the things I did in masonry all
10:17 the time. You lay it out dry. It's hard to make a mistake. Now, I got to figure out how I'm going to fasten it. Okay. Okay. I made these brackets. All I did was take this and cut it off here. These are going to be holding up my post. And I got to paint them up first. Maybe it'll help a little bit to keep it from rotting and rusting. Now I'm using these brackets. And I'm going right down against the post and drill my hole. And then I'm using this uh carriage bolts they call
11:02 it which goes right through. And this goes like this. That's what's going to hold that railing on. Like hole. And I'm using these. Forget what you call them. No memory anymore. And get that started in there.
11:52 And then just just drive it in. Lag nuts. I forget what the heck. Okay, I got these all lagged in real good and tight. And that tightened that up good. Look it. Okay, now comes the part where I'm putting this handrailing on. See, I kind of bought it and it fits right over the top like that. Okay. Hey, when I'm doing my angles, when I'm doing my angles, I could always use a a flat file. Keep going until I got it. Or you got a lot of money, high flute. Now, we're going to talk about the way I'm going to do this. This was
12:37 the old system. They had that down there and they drag a bolt down and they put a bolt down and it held like that and then they put this metal thing on top. Problem is that's all rots away. So what I did is I put that plastic piece down top and I'm not getting any water here anyway because now it's under cover. And then I'm going to drill down on the sides. And when you drill down it's like Lewis pins. Don't drill straight down. You drill at an angle. And when you did old stone work, they put the thing like this in a chain that would lift the stone up. So I was always taught, never do it this way. Always do it the other
13:24 way. So first I'm drilling a hole straight through. Then I'm getting my hammer drill with a masonry bit and drill down. Okay, we got our two holes drilled. So, we throw some water down there and wash it out. You know what I mean? Make sure that they go down there real good like that. So, I mixed up some rapid set cement and got it in the hole. Make sure it's in there
14:22 my bolt going through down to the bolt like that. This goes on the washer. Put the nut on and tighten it up. That ain't going nowhere. I'm going to get my little grinder and grind this up. That's it. All done. Now that the railing is in, we're
15:09 going to take this off and we're going to replace it with this. So, it's going to make it look a lot [Music] better. Well, I'm all finished. And like I said, I'm not a carpenter, but it is solid as a rock and I'm not worried about it. I got my 4 in space or less than 4 in between so no one falls through it. And I don't like putting anything on this channel except masonry stuff. But I did do the steps. It's uh building stones and masonry steps part 19. And you can watch how that all developed and how I ended up putting the railing on. Thanks for watching. I'm
15:56 Mike Haddock. I'll see you next video.
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

