powered by

Stop Floor Squeaks Through Carpet (No Rip Up!)

Video by Home Rapid Repair · 1 moment used in Oak Valley Designs's DIY guides · 5:15 long

Moments in this video

  1. 3:48–4:38 Break Off the Screw Head From How to Use a Squeak-Repair Kit on Carpeted Stairs and Floors, Step 5: Break Off Screw Heads (if applicable)

    Once the screw is fully driven, its head will be flush with the carpet surface. The next step is to break off the screw head. The carpet depth gauge has a small notch designed specifically for this. Align this notch over the small, visible screw head. Firmly press down on the depth gauge and then wiggle it left and right. The screw will snap off cleanly at its pre-designed score mark, located about a fifth of an inch below the subfloor. This ensures that no part of the screw head is felt or seen through the carpet, leaving a completely smooth and invisible repair. You can then gently brush the carpet fibers over the tiny hole to further conceal it.

The guide that use this video

Transcript

0:05 Everyone has annoying floor squeak somewhere in the house. What if I told you there was an easy way to fix it yourself with a simple device that is designed to even go through carpets with no underfloor access. With a simple cordless drill, this depth gauge to go through carpet and some simple but smart engineered screws are designed to go through the carpet and I'll show you they have a score mark in them that will snap off so you feel nothing and it doesn't destroy your floors. Now, the most important thing in this floor squeak repair is to locate the joist. Your joist typically go the narrow direction of your house. For most homes, that's front to back. A good place to start your investigation to find those hidden floor joist is a floor heat duct. It's always going to be located in between two joist. So, if you pop that off and you feel underneath the heat

0:52 duct, you can locate which side it's on. Now, once you find a floor joist, you can simply mark it and then every 16 in away will be the next one and you can work your way across your floor till you find that floor squeak and then get to the repair. If you don't find the floor joist, you're kind of wasting your time. So, this is the member you have to find. Okay, once you've laid out your floor and found your floor joist in your squeaky area, we're going to put these special screws right through the carpet. Don't worry, it won't do any damage. These have special threads that will grab onto the subfloor and reattach it to the joist taking the squeak out. And [music] they're pretty magical because right there they're designed with a score mark and in a moment I'm going to show you how those snap right off and

1:38 they'll be a permanent part of the floor underneath where you won't feel them or see them. I first was alerted to these floor squeak ender products on a episode of This Old House and I was impressed how it goes right through the carpet and then leaves no residue, no marks [music] that it was ever there. This product also technically works on vinyl and hardwoods as well. This is the depth gauge for hardwood, so we won't need that today. We're using it for carpet. This is the correct depth gauge for carpet. The extra long screw with just the narrow threads on the tip are exploratory screws. So, we think we have the squeak and the floor joist isolated here at the 16-in inch mark. You can drill through the subfloor and see if you hit anything solid. If it

2:23 wiggles up and down, you've missed it, but if it bits out and it kept driving and kept reversing, then you're good to go. The kit provides two of those exploratory screws. It also provided the special driver that we'll use to drill our magic screws. The special driver has a quick release if you want to use that. It's going to go into the driver depth gauge and it won't let it go any further, so it will set that screw just deep enough. Now, you want to take your depth gauge right through the carpet and you want to press it in deep. You want to hit the subfloor. You also should put your body weight around this area cuz you want to deflect the subfloor to uh stop the squeak, to push it down. Square driver bit came with the kit for the pre-scored screws. With your body weight

3:11 in place pushing down on the device, go ahead and screw it in. All the way down. When it stops, you've gone as low as the device will allow you. This screw is designed that the threads are now holding the subfloor to the joist and stopping the squeak. You can come in and use additional screws depending how large the squeak is. Now, the pre-scored area where the screw will snap off is about a fifth of an inch below the subfloor, so you shouldn't feel it. Now, the next step, if you look at your depth gauge, it has this little notch right here. That's designed to go over the scored screw so it can snap in the right

3:58 position. And then you're going to wiggle left to right. And the score snaps off. Let me show you on a new screw. It snaps right there where the manufacturer designed it to snap off, leaving the threads to hold the subfloor firmly to the joist. >> [music] >> Go ahead and feel that. There's nothing to feel. It's completely soft. That screw is set beneath the surface of your carpet and your padding so you feel nothing. >> [music] >> Use as many screws as you need to stop those squeaks. This device is patented and manufactured in the United States of America. You keep the device as long as you need cuz you might have more squeaks in the future. Now, this video was only about floor squeaks with carpeted areas. That was this device. It also comes with

4:44 this flat depth gauge device that's used for hardwood floors. You could use the same procedure to stop squeaks in hardwood floors and vinyl. Now, the only difference on that is your depth will be very important and you will also be left with a small visible hole that would have to be patched later. Let me know if you've done this repair or if you have any questions.

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Stop Floor Squeaks Through Carpet (No Rip Up!) — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.