powered by

Stair Mitered Skirtboard Pro Techniques - Complete How To Guide - Part 1

Video by Insider Carpentry - Spencer Lewis · 1 moment used in Oak Valley Designs's DIY guides · 14:08 long

Moments in this video

  1. 5:39–9:34 Mark Riser and Tread Cut Lines Using a Jig From How to Scribe and Cut a Stair Skirt Board to Fit, Step 2: Transfer Stair Profile to Skirt Board

    Utilize a custom-made jig, often referred to as 'Dutchman's pants,' which is specifically sized to match the thickness of your riser material (e.g., 1/2-inch plywood). With the skirtboard still temporarily in place, position the jig against each riser and tread intersection. For each intersection, use a torpedo level to ensure the jig is perfectly plumb (vertical) against the riser before marking the vertical cut line, and perfectly level (horizontal) against the tread before marking the horizontal cut line. It's recommended to mark the cut line approximately 1/16th of an inch higher than the actual contact point to account for potential inconsistencies and to ensure a tight fit when adhesive is applied later.

The guide that use this video

Transcript

0:01 hey what's up guys and welcome back to the channel spencer here in this video we're gonna cover mitered skirt boards for stairs stairs bewilder a lot of guys but it's really not that complicated if you know the right tips and tricks and have the right tools so in this video i'm gonna start by showing you how to figure the angles and cut a mitered skirt board this is gonna be a multi video series so that I can cover it in depth but video 1 which is what you're on right now is going to cover the skirt board cutting aspect of it I think you'll enjoy the video and learn a lot so stay tuned drop me a comment in the comment section let me know what you think and don't forget to Like and subscribe if you haven't already to get started on this I'm gonna come over here and grab one of my false tread end caps these are manufactured by LJ Smith they

0:48 come prepackaged currently they have two styles that I know of one is a traditional style and one is a contemporary style there are 4 pieces in each box the plywood riser the plywood tread and then 2 pieces of molding the first thing we're going to need to do is to remove the framing tread nosing on these treads on the end so right now I'm showing you first how that's done I'm just using a circular saw and I'm gonna knock these off and then I'm going to use a multi-tool to clean up the drywall I wanted you to see this first now I'm gonna go backwards and show you how I figured out where to cut these off at you got a notch this nosing out and you're gonna have a skirt board right

1:35 here and then your tread cap is just gonna sit on it like that and then your piece of nosing will go over it like so so you might think you need to cut it off you're not--' your nosing exactly with this line but I like to leave 3/8 inch gap here for the carpet to tuck around it you'll probably see that and it'll make more sense later when it comes to cutting these no Zing's off you don't have to be super precise about it the main thing is you just need to make sure that that tread nosing is cut further back than the riser otherwise it'll screw it up later down the road when you're trying to put the skirt board on also you really should be wearing eye protection when doing this a lot of times there's drywall screws that

2:20 are they just for some reason they like to put their screw right into the end of the tread and if you hit one of those with the blade it could be a bad deal so I'm being a bad example here next you're gonna want to have a really clean area to mark out your skirt board and if you've got any drywall that's proud of your framing it's gonna mess things up whenever you're trying to mark your cuts for your risers and treads so I like to go through with a multi-tool clean up all the drywall and take a broom and sweep off the steps and then we'll be good to go and move forward on the next step get it move forward on the next step no pun intended here

3:06 alright so now it's time to move on to the exciting part of our skirt board before we can do that we have to get the angle of the stair and as I've said many times on this channel I am supported by you basically buying tools through the links and the notes on these videos or through my Amazon store well this is a tool I will recommend that will make you a ton of money and make you way more productive the Sibylla 48 inch digital level is two hands down one of my favorite tools and in my opinion it is absolutely essential for stair work so I will definitely have that digital level list of the notes below I'd highly recommend it what I'm doing now is I'm marking out the bottom of my skirt board I use a 1 by 10 I try to maximize the visible skirt board so I'm dropping it

3:51 down about as low as I possibly can so now I'm just gonna take my longer level try and connects connect my marks this is not an exact science and I'm gonna put my digital level on top of my longer level with the angle that I predetermined my stair was set at and then I'm gonna get it just right and make a mark along the bottom of my level and that will represent the bottom of my skirt board here you can see just how easy it is to get the the angle of your rake with this digital level plop a longer level on here plop the digital one on top of it make sure I don't have any treads that are not in playing with the others as if one would be high and the level would be rocking or something like that then just

4:37 hit the power button and it's going to spit out the angle for you and you can go to town now that I have the bottom of my skirt marked and I have my angle all I have to do is get a rough measurement on the length make it a little extra long and then I can cut the skirt board and I'll tack it in place when you cut this thing your top cut is going to be whatever the measurement in your level was so if it was 38 degrees my plumb cut is 38 and then the compliment is gonna be the long cut on the bottom which in this case would then be 52 degrees first thing I'm gonna do is tack the bottom and then I'm gonna grab my digital level again and this is a really important part I'm gonna use that digital level and make sure that this skirt board is

5:24 exactly on the angle that I want it to be I'm not even going with my pencil marks I'm actually gonna use the level itself to make sure it's perfect then I'm going to put another nail on the top for the next step I always keep a jig in my stair kit some would call this riches or Dutchman's pants you'll see why in a little bit here okay so the next step I need to mark out the spaces on my strip board here these are called Dutchman's pants because they're shaped like a Dutch mums pants or Amish if you're familiar with that some people call them breeches but it's just a simple jig that will slide the skirt board and this needs to match the width of

6:11 you're right and material is so in this case these kits come with half-inch plywood for the riser this is a half inch jig I always save you can see here it's got SAV written on it and it's always in my stair kit if this board were to be 3/4 inch thick this jig would need to also be 3/4 of an inch thick so to mark the line where I need to cut the mitre for my riser I'm gonna take my jig make sure it's firmly pressed against the riser to by here and then I'm going to pull out my level my trusty torpedo level I'm going to be marking this front side because that's where the front edge of the mitre is gonna be and that's where I want to cut so I'm going to make sure that this

6:57 correct contact for whatever reason these never seem to be plumb so I'm going to take my level on the back side and I am going to move this until it's plumb I'm going to push this against the riser and I'll take my pencil and Mark that front edge just this process all the way down using my torpedo level get it plumb and then marking that front edge if you listen carefully you can even hear the mariachi music playing in the background from the painters outside

7:55 so now we've got our plumb line for our riser miters now we need to find the horizontal line for where we're going to cut for our tread I used the same jig can I just go to the back of the treads of the jig is sitting on the backside and mark the bottom here because this is level across then I'll come and do the same thing on the front make these two lines go away you don't have to get crazy precise with this because I like to cut my my make my cut line and actual maybe sixteenth higher than what my

8:42 actual mark is to ensure that it sits in my adhesive really nice now you'll notice here as I marked my level line look how far out of level this tread was and it actually is that far out of level so I make my level line usually a sixteenth higher than my highest mark that way the whole thing will sit down just fine if you just make one mark and the treads at a level which they always are it'll be screwed up so always make one mark the front and back even check if the tread is humped it could cause an

9:27 issue but generally if you go a sixteenth higher than your marks you'll be good and everything will be fine now we remove the stringer which was temporarily tacked in place the most difficult part of marking this out is knowing where to make your plumb cuts on the top and bottom of the stringer you can see I already had my Newell on the other side of the stairs so my plumb cut was based off of that there's a little bit beyond the scope of what I'm going to get into in this video though but maybe in the future I'll cover more on new newell placement it's extremely extremely important that on the bottom plumb cut your skirt board is gonna go up against your Newell that you mark that perfectly plumb the reason is that cut is going to actually help plumb the duel whenever you install the Newell as you can see

10:14 here this process really is not complicated and it goes really pretty quickly once you get the hang of it it's just a matter of having the right jig and kind of knowing what you're doing it'll take you one or two to get the hang of this but it's it's actually pretty simple making the miter cuts is pretty easy you're gonna set your mitre at 38 degrees and then your bevel at 45 and a half degrees to make sure that outside corner stays nice and tight over cutting it a little bit as a good thing when you get all the way to the bottom and you're gonna make your cut that your Newell will bump up against which will be your plumb cut I actually don't go with say my 38 degrees I'll make sure that my cut is gonna line up with that pencil line because I know I plumbed that with my

11:01 level and it's very important that that cut be perfectly level whenever you go back and install it because that's gonna make sure your nool is nice and tight and also that your newell is plumb you'll also notice I just bumped the mitre saw over about five to ten degrees that's going to ensure that the outside of this cut stays nice and tight to the newel and it's also going to allow me to put a little bit of adhesive in the back of that so that it'll bond the skirt board to the newel make it nice and solid now this is the only point in my personal workflow where I wish I had the makita 12 inch miter saw versus the DeWalt because the makita goes to sixty degrees on both sides so sometimes you get lucky and you can use the correct

11:48 side on the DeWalt but for the times it doesn't it's really handy for me to grab this HKC track saw and make the horizontal cuts with it my pencil mark is on the face of the skirt board and I just don't really have a good way of flipping it over which is what I need to do in order to make the cut with a miter saw so I just grab this thing and it works pretty good I forgot to mention it previously but you can actually over cut your pencil line about an inch doing this and since your mitering the plumb cut you do need to over cut in order to get all the way through that connection if you don't you'll have to use a handsaw to finish

12:34 the rest of the cut so it's easier just to over cut about an inch because your molding will cover that up as you can see here chocolate another one out for the HKC comes in really handy when it comes in handy makes quick work of this job if you don't over cut enough this is the tool I use there are two Japanese saws that I use one has the I don't know anything about Japanese hand saws but this one's got the stiffener on the back some situations you can't use this saw because of this so some of those other situations you need a saw like this that's just the blade I don't know what you call these but I'll link them in the notes below these two saws save me all

13:23 the time whenever I have to make cuts that aren't safe to do with a power saw or I just simply can't do with the power saw one more thing I like to do before I move on is cut a block for the bottom of the skirt board and this block just simply serves a purpose and that it gives my baseboard something to die into and that's what you see me doing here that's it for this video drop a comment below if you've got any questions or comments next video will cover how to install the false tread end caps on this skirt board by pre assembling them if you haven't yet make sure you like and subscribe so you don't miss out on future videos and also you can turn on notifications for whenever I do upload these videos that way you don't miss anything thanks for watching guys we'll see you in the next video

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Stair Mitered Skirtboard Pro Techniques - Complete How To Guide - Part 1 — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.