powered by

How To Install A Light Fixture - Step by Step

Video by Guy of All Trades · 1 moment used in Oak Valley Designs's DIY guides · 12:31 long

Moments in this video

  1. 0:38–1:17 Remove Old Light Fixture and Bracket From How to Replace a Flush-Mount Ceiling Light on a Stair Landing, Step 2: Remove the old light fixture

    With the power confirmed off, access the wiring by removing the decorative cover plate. For this fixture, thumb screws secured the plate; however, other fixtures may use different fasteners. Once the plate is removed, the electrical connections (typically twisted wire nuts for hot, neutral, and ground) become visible. Disconnect these wires and carefully remove the old fixture. Next, remove the old mounting bracket, which is typically secured to the electrical box with flat-head or Phillips-head screws. This bracket will be replaced by the new fixture's custom mounting hardware.

The guide that use this video

Transcript

0:01 hey everybody Dennis back with a brand new video today I'm going to show you how to install a light fixture so we have an old light fixture in our entryway I want to change it up to something new and improved something that looks nice and isn't as ugly as the one that's there right now I'm going to show you how to do that let's do this so this is the light fixture we're going to be changing out here this thing is I guess we could say David to put it nicely so what we need to do first is we need to shut off the power to this I'm simply just gonna kill the light switch for this all right so killing that light switch should get rid of the power to this now depending on the light that you have and maybe mounted a little bit differently this one has these little kind of uh thumb screws on it

0:58 this reveals the wiring in the bracket in your outlet box in the ceiling here so all I'm going to do is I'm just going to pop the wire nut off here that gets rid of that wire and I'm going to pull that one off and it gets rid of that wire now we know there's no power here because we killed that light switch that light is no longer on what we're going to do next is we're going to remove this old bracket because the new light fixture uses a new mounting bracket so on this one it is just two Flathead screws um it could be Phillips sometimes the newer ones are Phillips I'm just going to drop this out of here just like this and we'll set this to the side we'll grab our new light fixture uh we'll grab the the new mounting plates very similar to this it's actually just

1:44 a bar that mounts in between the two screw holes and we'll get our new length fixture up here is the mounting bar that I talked about so instead of having that larger one we're going to use this one here and we're going to reuse those two screws that came out of here we do need to ground our fixture and that mounting bar that we're putting back in here so what I'm doing is I'm using a bare piece of 14 gauge copper wire I pulled out of a scrap piece of Romex and I have one of these bonding screws so you can either use a flat header or Phillips on these and you can also use the 5 16 nut driver I like to use these because it gets a little better grip on here so in these metal boxes and this does not apply

2:32 what I'm doing exactly right now if you have a plastic ceiling box but for the metal boxes the Box needs to be binded to ground also this originally had both of these copper ground wires wrapped around one of the string relief screws in here so in order to get everything bonded including the box and the fixture we need to install this binding jumper so typically in these metal boxes there is additional holes in here so this one has an extra hole right in front of where that strain relief is that we're not using so I'm going to run this ground screw with wire right into that hole and we're going to tighten

3:18 this up all right so now this is the green wiring that I was talking about we call this a greeny it has a hole on the end here and what that does is it allows you to take a bunch of ground wires together wiring at them together and then have a little lead or a tail wire or whatever you want to call it coming out the end through that hole here so we'll tighten that on there we'll have this extra wire here to bonds are mounting bar and the light fixture itself there is a ground wire on the

4:04 light fixture itself so I'm going to take some lineman's pliers I'm going to tighten this up all right we want all our connections to be super tight when we do electrical work very very important so we're going to install this and we're going to tuck this one can go up out of the way and this one also and now one thing I forgot to mention here I shot off the power earlier I know this is not live anymore but if you have one of these non-contact voltage testers you can also stick it on here

4:49 you can also use a volt meter whichever you like just make sure you're safe this comes with a post we don't know where this needs to be set right now so we're not going to worry about it I'm just going to leave it loose and once we get the fixture up here kind of like a mock-up Mount will determine where that needs to be that we can secure it in place [Music] we'll make sure that's in there nice and tight now we need to ground this bar here so instead of putting this on here because this screw is a little small I will when I put the fixture up here I'll wrap that braided it's typically a braided copper ground wire I'll wrap that fixture wire around here and then

5:35 wire nut the other end of it to this ground wire and then after we make these connections everything will fit up there real nice this will be grounded and the fixture will be grounded also all right so here is our light fixture and like I mentioned we have the braided ground wire this is what it looks like we have two additional wires your black which is your hot and your white which is your neutral a lot of times uh these will kind of be all the strands on here kind of be all over the place I like to just twist them and get them nice so if it's under the wire that's really nice right so

6:22 what we're gonna do is we're gonna actually just kind of Tuck this out of the way real quick [Music] and we're gonna see how this fits [Music] on on this mounting piece right here [Music] there should be a hole in here [Music] sometimes sometimes you can just poke a screwdriver through if I think we're gonna do that it'll actually help you guide it in place too if you just want to stick a screwdriver up through there like that so

7:07 all right and we're just gonna we're gonna screw this on here and test to see if there is enough room inside of there to grab the light fixture and there is okay so we know that that post on that mounting bar doesn't need to be retracted or extended any so we can take this off now so I like to especially if it's a fixture I've never installed before I like to kind of do a little mock-up and make sure that everything is adjusted to where it needs to be now we can pull this out pull that back out and this guy and

7:56 we can take this and wrap this around that screw like I mentioned so uh instead of using the solid wire on there I like to use the braided wrapped around here and if you kind of wrap it around a little extra it'll help keep it from coming out from underneath the screw as you tighten it all right so that went around we're gonna move it to that side now you want to be careful especially if you let it hang like this it's typically strong enough on these smaller light fixtures where you can hang it from there if you do have a helper that'd be great to to help hold that for you we're going to make up the ground connection first so you can use the wire nuts it comes

8:42 with they're typically okay they're not the greatest I do like the deal brand they make some pretty nice wire nuts but we can use this without any issues and we'll tuck that all the way back up in the box so our ground is good now we'll connect our neutral you just want to make sure that your wiring is kind of out of the way where that post has to go so connect up are neutral now once again you want to make sure all your connections are really tight you

9:28 don't want loose connections with electrical anything loose will end up heating up and has the potential to cause a fire you definitely don't want that and you can tell like when you put the wire nut on you can tell if either wire isn't really engaging into the wire nut because you will be able to pull it out just going to take my linesman's grab that nut on there that lock the nut and give it a little twist to tighten it up so you can just stick your screwdriver right in here and it'll actually guide your fixture right over that post

10:15 just like that I'm going to take a peek around the perimeter of this make sure there's no wire sticking out there's not so good so for this particular fixture we have these glass pieces that go on so to install them this is actually really nice fixtures from Lowe's all we do is we take that off [Music] just barely all right you don't want to crank on this because you will crack the glass you just don't want it to rattle [Music] now I got these cool kind of Edison style LED bulbs

11:07 that I want to try out in here and see what they look like pretty cool right [Music] all right so our last step is to put this metal baffle in place here so this just slides up in here like so and it's a little retainer goes on here and tightens up and it's more aesthetic than anything it really doesn't have a function to you know to hold the glass in place or anything it's more for looks it looks pretty cool

11:53 and we'll tighten it up here and let's test this out so it looks like all right so we're up and running and installed everything looks nice all right everybody that wraps it up for today's video if you have any suggestions on new videos you want to see make sure to drop it down in the comment section below also make sure to hit that like button and that subscribe button so you don't miss any of our new videos got a couple new ones coming your way soon thanks for watching

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

How To Install A Light Fixture - Step by Step — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.