powered by

How To Hang a Picture - Ace Hardware

Video by Ace Hardware · 2 moments used in Oak Valley Designs's DIY guides · 2:56 long

Moments in this video

  1. 1:46–1:55 Locate Wall Studs for Heavy Frames From How to Hang Heavy Pictures on Drywall in a Stairwell, Step 1: Locate Wall Studs

    For objects weighing approximately 15 pounds or heavier, it is always best to anchor your fastener directly into a wall stud for maximum security. Use a stud finder (like the Black & Decker Bullseye shown) to locate these structural supports within your wall. Hold the stud finder flat against the wall and move it horizontally across the desired hanging area. The device will typically light up, beep, or display an indicator when it detects the edges of a stud. Mark the center of the stud on the wall using a pencil. If you can successfully anchor your fastener into a stud, you will achieve the strongest and most secure hang. If a stud is not available at your desired location, you will need to use heavier-duty fasteners designed for hollow walls.

  2. 1:55–2:27 Select Fasteners for Heavy Objects Without Studs From How to Hang Heavy Pictures on Drywall in a Stairwell, Step 5: Install Heavy-Duty Drywall Anchors

    If you cannot anchor a heavy object (15 lbs+) into a wall stud, you'll need to use heavy-duty fasteners designed for hollow walls. First, determine the exact weight of your picture by weighing yourself holding the picture, then subtracting your body weight. Check the fastener's label for weight and material guidelines. For hollow walls like drywall or plaster, self-tapping threaded anchors are a good option. These don't require pre-drilling; you simply insert the anchor and screw it directly into the wall using a drill. Another type of heavy-duty fastener is an expanding anchor. For these, you pre-drill a hole into the wall using a drill bit slightly smaller than the anchor, then tap the anchor into the hole with a hammer. As you tighten a screw into the expanding anchor, it spreads out behind the wall, bracing against a larger surface area for increased stability.

The guide that use this video

Transcript

0:06 [Music] although it's simple to hang a picture there are two main tricks to getting it right the placement and using the right type of hanger the rule of thumb is to hang art so the center is about 57 to 60 in from the floor or roughly eye level for a smaller frame you can eyeball height by holding up the picture make a light pencil Mark or use a piece of painters tape to Mark where the top Edge of the frame will go now figure out where to place the picture hanger flip the picture over and measure from the top edge of the picture to the spot where the Fastener will go here it's 2 in transfer that measurement onto the wall by measuring the same distance down from the mark on the wall place the lowest point of the hanger at the Mark and attach the Fastener to the wall hanging a larger picture can be trickier

0:53 on the wall Mark the centering height of about 57 to 60 in from the floor to find the picture Center measure the height and divide that number by two for example this artwork is 40 in high so we made the Mark at 20 in second figure out where to place the wall Fastener with a wire hanging like this stretch it out as if it was hanging and make the mark measure from the spot to the center Mark of the picture here it's 8 in so we'd measure 8 in up from the mark on the wall and that's where we'll place the fastener the right Fastener depends on how heavy an object is and what you're anchoring into use a small nail to hang a light

1:39 object with a d-ring or Sawtooth hanger on the back a hook type Fastener works best for light objects with wire hangers for objects about 15 lbs or heavier it's always best to Anchor your Fastener into the wall stud if you can't you'll need a heavier Duty Fastener to figure out how heavy your picture is subtract your body weight from the weight while you're holding it for hollow walls drywall or plaster look for self-tapping threaded anchors self-tapping means you don't have to pre-drill a hole you just insert the screw and drill it directly into the wall some anchors spread out behind the wall to brace against more surface you pre-drill a hole into the wall using a drill bit smaller than the anchor then tap the anchor into the hole as you

2:24 tighten a screw into the anchor it expands behind the wall to prevent your picture from scuffing the wall stick self-adhesive felt pads on the back of the frame before hanging it up now if the piece is Warped you can stick Velcro on the back to hold it against the wall you want more helpful tips and advice visit your neighborhood Ace and find Us online at acehardware.com [Music]

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

How To Hang a Picture - Ace Hardware — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.