CONCRETE REPAIR/PATCHES (Part 6) Mike Haduck
Video by Mike Haduck Masonry · 1 moment used in Oak Valley Designs's DIY guides · 12:59 long

Moments in this video
- 7:09–8:52 Shape and Finish the Mortar
From How to Fix a Crumbling Concrete Step Corner, Step 5: Shape and Finish the Repair
After applying the mortar, the presenter uses a trowel to roughly smooth the surface, ensuring it is level and flush with the surrounding concrete. He then uses a concrete edger, running it along the top and bottom edges of the newly patched area to create a clean, rounded profile. Following this, a wet sponge is used to gently rub the surface, further smoothing it, removing any minor imperfections or trowel marks, and creating a more uniform appearance. This sponge finishing helps to consolidate the surface and bring fine particles to the top.
The guide that use this video
Transcript
0:05 well today what happened was there was a big chunk taken out of the front of the porch where you step off of it right here and what i did was i just patched it up i'm gonna show you how i did it now we're gonna fix this porch right here it's kind of normal this porch is about 50 60 years old you can see the top is peeling off right here it's cracked there's even a little crack behind it and they try to fix it before you see that metal right there you can't preach enough about rebar you never know what rebar it expands and it breaks everything apart so i can't rip it out of there i gotta leave it in so gonna try to make this stick but
0:53 let's look down here see that crack that goes right through here they poured this right into the top cap and it held on and it cracked it here so i know just by looking at it there's a crack going right through so i'm going to do is kind of scar it up first and then i'm going to uh pour it here's what i'm going to do with this i got my little grinder i even have a little amazon site we could buy them blades or only 15 bucks or something a little grinder i'm just gonna scar it up like this
1:49 i got it scarred up real good you could see how deep i went i made some extras and make sure it sticks now since we did that we're going to wash it off good anytime we're dealing with this kind of cement we got to make sure it's wet for one thing we want to get all the dust off for the second thing what we're going to do is form this so kind of got an idea here where i want it to go and the reasons why so i got it there for my lead you see the ledge and right here i don't want the cement going down in there so i'm going to show you what i'm going to do i'm going to get a little sand i'm gonna
2:37 put the sand in there and pack that sand i don't want the cement all going down there just like that doesn't have to be perfect because no one's gonna be down there looking we got the sand packed down in there i'm going to wet it again see how fast that's drying i don't want that i want that soaked i want that wet now i'm putting this form up like this just to hold that against there let's look at it this way see now i just got to fill this pocket in here with the cemento this repair i'm just using the mortar mix the same order i don't look at it as border anymore look at it as concrete it does such a
3:24 good job i never had a problem with it i'm going to mix some of this up add a little bit wider i'm gonna go with that right now okay and like i told you gotta make sure it's wet good and wet now i'm just gonna put it in it's getting hard already i want to plaster it up into those ridges i left that's what i wanted to stick to
4:12 get it in the ridge is really good i'm really content i did a good job getting them in the ridges and then i just fill it up stops getting hard already get everything out of the way here it's hard to see when the sun is just looking good though like i said it's getting hot already
4:57 i'm gonna get it somewhere close there's a little more up here instead make sure it's wet first i don't want to stick unless it's wet i'm going to bleed it in the sides it has to be wet
6:07 so pretty happy with it now i got my edger see the edger they're running around the top now let's get the sponge and just run around the top here you could kind of gauge it a little better sometimes i'd use uh some menthol that don't have any sand in it [Music] well i don't think this case matters
7:17 um [Music] in a few minutes we'll take the forms off so we could just see what's getting hard already so we got to get that form off pretty quick and anytime we take a form off of this stuff don't take it straight off and hit it sideways that's the end of that one we're looking
8:03 under here get this out of here and out of there that out of there that's looking okay for the way we formed it now we just got to fill in the little spots top looks good talk about that a little later i got to fill this in here make that look a little better just put that there i'm going to mix some more rapid set up one of the problems with rapid set is it's hard to get rid of these i don't know what you call them the honeycombs so you kind of got to go over it a little bit
8:51 the stuff dries so fast that it's almost impossible to get them off i just did a a whole torch not a whole forge but a half a porch like 30 videos behind these days i get that out show you how i did the same thing and get that up in there see it's still it's still soft enough to scrape it like a sculptor what you're trying to do
9:40 is get it where it's all working for you that's that and get your sponge go over the top of it like that a little bit on your sponge if you wanted to get those honeycombs as we call them see that no big deal no big deal just getting it done now i'm going to come back a little later maybe
10:26 we see anything that don't look right we'll do it again no big deal so it's looking good a couple hours later if i want to really sharpen it up let me show you another little thing here i'm going to pull this out of here i'm gonna pull this off of here this is the diamond blade
11:21 just like that you could take this wheel you see that wheel and they got some high spots up here this is where the paint started or whatever they had you could just grind it down and you could go over your whole porch like that and then just paint it with a deck or a deck or a stucco paint so a couple secrets there now we want to give it the test this is only a couple hours lying but
12:06 nothing wrong with it so when i do a job like that i used uh the mortar mix to rapid set back in the old days you'd have to form it put your portland in you'd have to wait a couple days to go back now a couple hours later you're done it was real fine real fine fill-ins i'd use the cement all it's fine and you can see that on my concrete step repair and then i just paint it it's like doing body work to a car i use this as a grinder and i grind it down i have sometimes a little site to be in my description box thanks for watching until next time i'm mike haddock and that's it
12:53 [Music] you
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

