powered by

Building The Nantahala Retreat #27 | Stainless Steel Cable Rails!

Video by Perkins Builder Brothers · 1 moment used in Oak Valley Designs's DIY guides · 16:56 long

Moments in this video

  1. 8:20–9:15 Swage Cable onto Fittings From How to Tension and Adjust Stair Cable Railing, Step 2: Attach Tensioning Fitting to First Cable End

    Insert the cut end of the stainless steel cable into the appropriate end fitting. Use a heavy-duty swaging tool to crimp the fitting onto the cable. For a robust connection, first, swage the fitting once. Then, rotate the cable 90 degrees within the swaging tool and swage it a second time. This double crimping method ensures maximum strength and prevents the cable from slipping under tension. The swaged end will then be threaded into the tensioning turnbuckle.

The guide that use this video

Transcript

0:03 [Music] we're back for another episode of building the nantahala retreat today we're going to do some cable railing we got tyler here from e-rigging and haas stainless you have a nickname or something cable guy cable guy all right so we're gonna get going on these cable railings check it out all right first step here we have to decide our cable spacing we're gonna use a four inch spacing and that's the maximum amount allowed where we live might be different where you live and we did check with the inspector let's actually roll a bit of that footage of his explanation of how tight they need to be okay cut to that yeah okay you got it for how tight do we need to have these cables exactly well he said a specified attention is fifth string on the banjo piston okay so uh banjo types what he

0:50 said banjo type quote banjo type yeah so i'll get get out my banjo tuner and uh we'll get these things dialed in all right and we're back it's pretty technical actually so uh you might want to rewind the video and check again um four inches on center i have a scrap piece of wood here this is five and a half wide this one's for the six by six posts i made another one three and a half wide for the four by four posts i'm actually even going to screw a little edge fence on this so it'll register and i can actually stick a quick clamp on it and that way it keeps me from having to hold it and i can just drill it very easily i'm going to spot it through the jig with this bit i am not going to drill the actual hole through the post with this see it'll just come through make a little tick mark in essence and then we're going to use a bigger drill bit to drill through from both sides okay and

1:37 meet in the middle there's a couple reasons for that but i'm sure you're gonna and there's a country song about that delete that anyway so i'll spare you [Music] jamie's got a few pro tips about using wood templates and jigs he tried this once but it took about 10 minutes so hit it okay this is made of wood it's it's worthy to note that it's symmetrical the distance from the top to the first hole is the same from the bottom to the first hole because see i would go this way on this one then i have to flip it over so it is important it's symmetrical top to bottom there's no top and no bottom i'm doing good also since i'm drilling through here the wood is soft enough that i could wallow out the holes if i'm not careful so i put the bit in without spinning the drill and then i drill my hole and then and i

2:23 move it as little as possible to retract it by the time i get done using this it'll probably be a little bit wallowed out shot and i'll throw it away if you're going to make one that you want to reuse like all the time make it out of metal or something and use some kind of collar or sleeve like a uh you know those things that you drill shelf uh pins with adjustable shelving pins sure they come with a little collar and a spring okay all right an undersized bit and an oversized starting to be like what happened last time i don't remember there we go now that is in there and just so i don't have to mess with it here we're gonna

3:16 all right this is the easy part i think [Music] this is what we're pre-drilling with for our anchoring screw which is a stainless steel trim head screw because stainless steel is a little more brittle is that is that what you call it i would say it's a little it will snap so even though it's a small screw we're pre-drilling that's what jono's doing and uh it's very important [Music]

4:10 this is the system we're going to be using today by haas stainless called the axis did you name that no i didn't it's a pretty ba name it is yeah it's pretty cool this is the tensioning end he's got a stop in right here stainless steel screws very slick and streamlined and it's going to look amazing yeah should be easy it's supposed to be an easy that's all that's important right there that's the real important word it works for everybody the easiest way to cut it if like you're cutting it by yourself is to get 100 foot long measuring tape and then whatever the length of the cable run is mark the measuring tape at those increments walk it all the way down and as you walk back you just cut it on the way back walk out again and it works out you can do it really quick okay pro tip yup hey pro tip you need to hit the gym bud i don't know

4:56 if it's just the camera yeah but uh here we go we got like he's more aerodynamic okay in the event of a bear here's a look at our stainless cable eighth inch and he knows a lot more about this so it's type 316 stainless steel cable and the cable construction is 1 by 19. so 1 by 19 is basically you have a solid core strand wrapped by 19 uh smaller wires or cables there it is yep

5:43 um and so basically it's a stiff running cable you don't want cable that's going to stretch a lot with cable runs so it's a very stiff running cable and then it being type 316 it's going to be the most corrosion resistant which is good for the weather you know it's good for saltwater environments that sort of stuff so yeah i mean it's kind of your preferred cable for cable railing system look at the man see he gets down in there and gets eagle eye with it what's your job out here ah blowhole guy that's a pretty good name it's a very important job dude as far as cable guys go this one's the best cable guy ever you can see these holes are way bigger than our eighth inch cable and that's

6:29 because we actually drilled for this which is a post protector they will go into each side like that and look really slick and guide the cable in we're gonna go there there on all of our intermediate posts [Music] so pro tip with this is whenever you're putting in your wood post protectors they're kind of a crucial thing because if you forget one and then you swage each end of your your cable to your fittings if you forget one you have to cut the cable you can't undo the swage and the whole run has to come out so

7:14 what i like to do is i'll come in and i'll pre-install all the wood post protectors on one side the post and then as you feed your cable from this direction they're already installed there and then as the cable comes out the back side of the post you just slide it right onto the post and put it in the hole and that way you won't forget any yo good job kibble guy [Music] jason's using the clutch on his drill here set it number nine that seems to be

8:00 about right that's a good idea for stainless by the way i think so you know what tyler's just assembled here we'll hold the cable in the end that my fingers are holding this on and the other end will screw into your stop and the cable will be swaged which means crimped into that piece and this will be threaded in and it'll look like that hold still there you go i noticed you gave that two swages is that normal yep yeah so you switch it once and then you're gonna switch it once and you rotate it about 90 degrees okay swage it again okay cause there's a lot of force on these from what i understand yeah it's actually for as small as it is they're really really strong so all right patrick hit it

8:46 patrick what do you mean patrick patrick swayze [Laughter] nobody puts baby in the corner i'm not much of a bet man but i will swage you 500 that you can't do this in 30 minutes that was pretty funny [Music]

9:41 all right so this is the axis turnbuckle and if you don't know what a turnbuckle is they're pretty straightforward it's a tensioning fitting so this side of the turnbuckle body that you see right here is left hand threaded and this side of the turnbuckle body is right hand threaded and then as you rotate this turnbuckle it's going to draw these two together which is going to tighten your cable so what you're seeing here is this little threaded stud that threads into the receiver then your turnbuckle threads onto it like so then the swage end that actually attaches to your cable is what's going to thread onto this other side that's it

11:10 biggest pro tip yep overall you want to make sure that the cable doesn't twist so for this one you'll see as you increase tension on the turnbuckle it'll squish the cable and the cable have memory to it and then whenever you let go you think everything's good and it's all tightened up and then you come back a day or two later and all of a sudden your cable slack so because the cable will spin and basically spin the threads back out exactly so you want to make sure that all right that's good and then yeah you want to keep it neutral with a pair of vice grips you want to pop on your insert your 7 64 hex wrench that's right and then rotate till it's nice tight boom just like a banjo tyler's going to tell us another pro tip about tightening the turnbuckles in a certain sequence

11:56 much the same as how you would tighten the lug nuts on a wheel in a certain sequence yes yes okay so basically um in this case we have eight rows of cables so you can just pick your whatever one or two in the middle that you want to start with but basically what you'll do is you'll tighten first you go to the one above it and then one below it and then you're going to repeat that sequence and you're going to work your way out so basically you're starting with your middle cable or your closest to middle cable then you go to the one above it below it and then as i said you work your way out until all and what does that prevent it prevents basically from them being lopsided because if you start at the top down then what you'll do is is your post even if you can't basically see it your posts will bend in like this and then you and it'll teeter-totter and you want the post to just nice and even get

12:42 tightened so that's why you go on the sequence good tip yep bro we should do cable on every house this is awesome sit here and have a little cocktail all right [Music]

13:39 this is phenomenal bro are we getting paid today yep perfect so if you do get a couple cables crossed up like like we did right here this was not staged that was not on purpose luckily we can go ahead and unscrew this from the termination swap them out yep this is one of the best that is a good design it is well it's one of the benefits of not having like a through post system because of the through post system you can't unscrew it but with this access system that's kind of one of the not necessarily like a purpose-built feature but but hey we're gonna get screwed up here yeah oh yeah it's gonna happen we got our flat section done jamie uh we're done with our section here so i'm happy for you so we're gonna do this angled section

14:26 and as you might have guessed the cable needs to angle just like the steps do and we're gonna wipe this camera off and to do that we've got a special termination and uh it screws in like so and then hey jason let's vanna white this thing i can't hold it let's show off what it does okay so if you look closely it's got a swivel and a slot and so the cable can go at any angle up or down so that's nice thank you i had to buy an e yeah okay [Music]

15:46 dude what are you doing i'm just staying in this it's gonna cap that one post in the corner oh i thought jamie was gonna make one exactly that's why i bought this for fifteen dollars at lowe's so he didn't spend five days making one in the shop that would cost us five hundred dollars but it'd be so nice it would but you look at this it's done and it costs fifteen dollars instead of five hundred genius [Music] hey thanks for building with us today we really appreciate it we really appreciate tyler coming up from louisiana bringing us great food and helping us install these cable rails so make sure to get onto e-rigging.com that's where they sell their stuff and also haas stainless their usa company and they stand behind their products also if you've enjoyed this video or

16:31 found it entertaining please remember to subscribe give us a thumbs up and we'll see on the next one

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Building The Nantahala Retreat #27 | Stainless Steel Cable Rails! — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.