#210 DIY Garage Stairs w Platform
Video by Kens Karpentry · 1 moment used in Oak Valley Designs's DIY guides · 8:37 long

Moments in this video
- 5:24–6:18 Cut Stair Stringers from Lumber
From How to Build Basement Stairs, Step 2: Cut Stair Stringers
Using a framing square set to your calculated rise (8 inches) and run (9 inches), mark the step pattern onto long pieces of 2x12 lumber. Carefully cut along these lines. The builder uses a circular saw for the initial straight cuts along the top and bottom of each step, and then switches to a reciprocating saw (Sawzall) for the inside corners. This combination of tools allows for both speed on straight lines and precision in the tighter, notched areas, resulting in a crisp, clean finish for the stringers. Once the first stringer is cut, it can be used as a template to mark and cut subsequent stringers, ensuring consistency.
The guide that use this video
Transcript
0:03 so i have the calculation where 112 inches concrete floor to top of the wood floor upstairs so that works out perfectly for an eight inch rise so it would be uh 14 steps the 14th step will be the floor upstairs so we'll only need uh 13 steps out of this minus one for the platform in the corner because we're going up to a corner platform and then up the rest of the way it's an eight inch rise and a nine nine and a quarter inch tread actually nine inch tread again with an eight inch rise the very first step you have to subtract an inch
0:50 and a half to allow for the thickness of the two by stair tread because that will bring you up eight inches and that but the rest will just follow suit follow suit i don't know what that means okay so the platform will be right in here these stair treads are the ones that are going to go up to the
1:35 platform and all you can see a problem there's a concrete curb here so we'll just cut that off because i really would like it to set close to the wall just to be more firm and so the stair trade goes all the way out there so we'll modify this just a little bit and should be good to go okay we'll have a level just to make sure it's level
2:35 okay i've drawn lines across here as well as across here make sure we're good and level there also this is we're going with eight inch rise but this would be the top of the floor would be 24 inches so i subtracted the 5 8 plywood that we're using so this mark is 23 and 3 8. we'll put on build our framework here now all right finish putting this platform frame together
3:32 one-handed that's pretty clever let's see if we can do it [Music] let's just check this perfect perfect perfect we will put a support here just to make sure because that will sag if we don't
4:41 i always pick the best the best edge to be on the front [Music] two treads done i think 11 or 12 more to go there's a platform cut out of 5 8. [Music] hey it fits 36 by uh 36 by 42 so the the stair stringer will sit right on here completely so it supports that i still have to make those
5:52 okay so this one came out right on so now we'll use it as a template for the other side then we'll have both springers the same i like to cut these out with a sawzall because it gives a nice crisp inside corner yeah inside corner we are ready to put them up let's go inside and look someone had asked about cutting out the floor for the stairwell so we'll do that
6:39 okay now so now we can see we're going to put in the last eye joist we'll set that in header it off and then we're ready to put the stringers up i think we have all the weapons ready we're going to put this eye joist in we'll tack it in place then we'll put the the header across so when i pick this up joe can you hold it it's not real heavy just leave this free so i can whack more a lot more [Music]
7:28 yeah you want to whack it from up there i'll hold it sure just hit it on the top of that don't hit me if you could help it all right they're all in position now we do stair treads
8:17 you can rack these stringers a little bit just by flexing this in or out it helps to straighten straighten this up a lot if you work it as you go
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

