powered by

Steps up to the Platform. Build a Playhouse 3/15

Video by Land to House LLC · 1 moment used in Oak Valley Designs's DIY guides · 15:56 long

Moments in this video

  1. 11:30–13:16 Install Balusters From How to Build Basement Stairs, Step 8: Install Handrails and Balusters

    Install the balusters (vertical spindles) for the railing. Pre-drill a pilot hole into the angled end of a 36-inch baluster and partially drive a 2.5-inch screw into it. Position the baluster against the stringer, aligning it correctly, and drive the screw into the stringer. Ensure the spacing between balusters is no more than 4 inches to meet safety standards. To mark the position of the second baluster, use a speed square from the previous post. Place it against the installed baluster, draw a line 4 inches away, then use the diagonal to mark a line downwards. Repeat this process for all balusters until the railing is complete.

The guide that use this video

Transcript

0:02 hey i'm seth johnson with land house and you are watching the playhouse build [Music] no no way do we bye in this video i'm building the staircase to get up to the playhouse hope you enjoy to get started with this staircase build i have two eight foot two by sixes set up against the side of the playhouse base i'm going to be making a 45 degree cut here on the top of these two boards

0:47 so that it will meet up flush with the building side let's do that first i'm going to use a speed square to make this cut i'm going to line the 45 up on the end of the board make a mark and now i can offset this a little bit and use it as a guide for my circular [Music] saw [Applause] now because the ground is not quite level here i've actually cut off five inches from the bottom your setup may be a little different but i'm just cutting off five inches to bring the board down from here to here it's the same 45 degree cut

1:34 from before that one was here on the end but i actually want to move down five inches so i'm just going to take where that previous line or cut would have been and come down five inches and that should give us the removed five inches that we need here [Music] so far so good have those boards on the ground and then up here i may actually dig out a little bit on the ground and put a paver stone under them just to keep the water from being on them all the time just from the ground contact because the first cut was at a 45 it makes everything else a lot easier every step is going to be

2:20 10 inches apart so the first one is already done here which i've come down and marked 10 inches so let's move on to the second one here i'm going to mark 20 inches and then i'm going to come down again at 21 inches the reason for that is uh i can take my speed square from let's see the bottom here and match up that line draw across and that's going to be a level line on the board come down to the next one here mark again okay now i can take a combination square

3:06 and because this board is five and a half inches i've taken two and three quarter inch and from the top i can mark out here wherever this line intersects with the other one is going to be the midway point of the board on that line so what i want to do is take my drill so now taking an eighth inch bit i'm going to place right here in the middle of the bottom line and drill a hole taking a three inch screw from the other side just going to go through here so that it barely shows

3:52 okay and that's the place i'm going to put the halfway mark of my 2x6 step my steps are going to be 2 feet so just going to mark out here and cut a two foot two by six with my square still set at two and a half inches i'm going to find the center of this board now to find the line that goes straight up from this middle post that we've just made i can use my speed square sliding up here and that will tell me a midpoint up from the screw that i can use to mark out where the

4:38 board is going to go so just sliding the board into position here i'm going to match up the top line with the top of the board and also matching up the line that was just drawn so i can take my screw through that position [Music] now there's a single screw in the middle point of those two steps obviously that's not going to hold anybody up but it's going to allow me to spin this up or down to find level so first of all i'm going to off camera put in the rest of these steps until i have all eight of them installed

5:24 and we'll come back and level this out now the ladder is propped up here against the side of the playhouse and because of the angle it shouldn't take much to prevent this from going anywhere so i'm going to put three nails in here go ahead and pre-drill just to make sure nothing splits and then later i'll be putting a metal bracket on here also just to make sure it doesn't go anywhere with the screw in the front and the three nails on the back i don't see this going anywhere but just as a safety measure i'm going to be using this metal bracket and that's just going to be here to make sure that this doesn't go anywhere so just to make sure that the

6:12 rail here doesn't split i'm going to put just a couple of little pilot holes just to get this screw started and i'm gonna go ahead and put just some one and a quarter screws here now these are exterior screws of course i'm just going to fill this plate up to make sure that it's nice and secure now that i know the stairs are firmly secured to the base it's time to get these steps level so just going to stick my level up here and some of these may be a little bit tight so you may have to use your adjustment tool

6:58 too far there we go now i'm just going to be using a 8 inch an 8 inch drill bit to go into my rail here now it's time to install the railing i've got these 36 inch balusters that have the angled cut on both ends so i'm just going to be making my rail at about the 36 inch mark so let's jump into that real quick and as you can see i already have the first one done to use as a reference i've got an eight foot two by four that i'm going to cut into two 36 inch pieces and this will be the supports upwards on the rail if that

7:44 makes sense to prevent the board from splitting i'm just putting a pre-drilled hole here i'm going to go ahead and get started with a three inch screw using the speed square i'm going to put this right up against the base here and i'm going to mark at the three inch mark and then i can actually use my diagonal to draw a line down and that's going to be the edge that two by four goes on now i'll be using a level to make sure this is in there correctly in just a moment but

8:30 for now i just need to get this leveled up here okay i'm going to get my 2x4 into position here the back corner is going to be lined up with the bottom of the step just like that i'm just going to go ahead and get that single screw put in there and that'll just hold things into place so i can use the level to level this out

9:17 all right that's where i want it time to just fill this thing up with some screws i'm gonna put five in here total now i want 55 inches between the back side of this board to the front side of the other so i'm just going to measure out the 55 here now at the speed square i can set this up align it to that bottom mark and draw that line so that's where the front side of that 2x4 is going to be just going to line the other 36 inch board up on this line here

10:05 now i have a 10 foot 2x4 that i want to cut in half so two five foot lengths here this five foot board is to go on the inside it's a little awkward to work with here but i want it to be about uh midway point here and then just above the top and to make this easy to draw a screw into i'm just going to kind of mark out here just a little uh a spot so i can see where to do a pre-drill hole

10:52 i find it super helpful to go ahead and start a screw in there so you can get it into position okay just look on this other side here where i made those markings matching up the top roughly and then just going to put this in here for now okay and now let me go up to the top and get the other side okay from the top i'm just going to make sure this is slightly above this other post here now for the balusters i'm going to use pre-drill hole again

11:39 and then putting a two and a half inch screw into each of these turn it around and do the same on all of them i need six total for this staircase now using the speed square from my top post i'm going to come over four inches and make a mark there and then i can use my diagonal again to just draw that line down and then let's go up to the top i'm going to do the same thing where i use my speed square to come out four inches and then use that diagonal to draw the line down

12:32 and that's going to be the location of the outside of the baluster so i want to just make sure it's down from the top by about a quarter inch or so and then i can just use a single screw to hold that in there now back at the bottom i want to just use my speed square to make sure that this is correct at the four inch mark and it is and then just get this piece screwed in and there we have it that's the first of the six balusters so i'm just going to continue that process until i have all of those done

13:17 now that i have all the balusters in the last step is to put the top on and that's where the other half of that 10 foot board comes in so to get this started i'm just going to be pre-drilling here drop you down so you can see a bit better so every about a foot i'm just going to put a new hole in here i think i started off just a little bit off from the top i'm just going to be using the three inch screws again go ahead and get them started okay just going to line up the bottom slide this up here

14:02 and that concludes the staircase build for the playhouse let me give you a closer look i decided not to put the railing all the way down here to the bottom i figured that kids might want to run back up quick and the slide is actually going to come off right here so they can slide down and just run back up there and the railing won't be in their way so i've got everything lined up four inches is the uh maximum distance you can have on these balusters and so definitely try to keep within that whenever you're building yours i feel like the five screws on the bottom there will be sufficient and then one in each of those balusters definitely want to come back with some

14:47 sandpaper and pull off some of these sharp edges let's take a look up here at the top now if for some reason you feel like your steps are still not sturdy enough you can put some blocking up under here with another screw or nail to give it more support but i'm 200 pounds and there is zero movement currently in these steps i'm definitely going to come back and paint this now the other railing will come up right here and i may just extend just a little bit to make sure that this is covered as well but for now i think it's going to work quite well it's a good height for someone that's my

15:35 height thank you so much for watching this playhouse build video if you've enjoyed it hit that thumbs up button and be sure to subscribe there are several more videos in this series on the way thank you so much for watching and i will see you in the next video bye

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Steps up to the Platform. Build a Playhouse 3/15 — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.