powered by

Install front Porch Rail. Build a Playhouse 12

Video by Land to House LLC · 1 moment used in Oak Valley Designs's DIY guides · 7:20 long

Moments in this video

  1. 3:09–4:49 Install Balusters From How to Install a Deck Stair Railing, Step 4: Install Balusters (Spindles)

    Prepare several narrower wooden balusters. To prevent wood splitting, pre-drill pilot holes at both the top and bottom ends of each baluster using a drill. Position these balusters vertically between the horizontal rails, ensuring consistent spacing (e.g., 4.25 inches as mentioned by the creator, or per local code). Secure each baluster in place with exterior screws using an impact driver, driving two screws at the top and two at the bottom. Before final fastening, use a spirit level to verify each baluster is plumb.

The guide that use this video

Transcript

0:02 hey i'm seth johnson with land house and you are watching the playhouse build [Music] no no way bye doll to get started on this playhouse rail build need one rail on this side the gap in here should be fine need a rail right here on this piece one that comes out here and then also need one

0:48 that will be spanning this whole side over here so uh these balusters will be spaced here i'm gonna do four and a quarter inches on each one of these i feel like that's going to be good enough so let's go ahead and get started i want to use some of my 2x4 material here to cut three foot boards that will go up along here i'm going to use some exterior screws and also a bolt or two to make sure the rail is nice and firmly attached here so our first measurement is going to be to cut a three foot board that'll go up along here i'm gonna measure mark and cut four boards at three feet

1:39 i'm gonna take my first three foot board here and i'm going to drop down five inches from the top of the decking boards here and i've got that marked right where i want it and then just simply going to put a couple of these screws in here to keep it in place and to make sure this board is nice and secure i've got a four inch quarter inch bolt i'll be putting through here so i'm just gonna drill straight through the middle and i've got the washer that i'll put on one on each side here

2:29 and then i'm just going to tighten that down and we should be good to go now to span from this board across i'm going to want a board cut to four foot okay i'm going to place this board here in between the two of these i want to make sure it's level in here i figure i'll need four of these balusters to go up here in between and to make sure it

3:15 doesn't crack i've got a drill bit here so i'm just going to be pre-drilling the wood on both the upper and lower portions go ahead and start the screws in here to make it easier okay and now i'm going to set this up here and i've marked out where i want it on this lower portion so i can go ahead and get that screwed in

4:02 and before i screw in the top one i want to just take my level here the sun's out so it's kind of hard for me to show you this angle from down below but uh this four foot board sticks out to this point and i'm just going to bring a board down here and i'll have to build this out a little bit by sticking a couple of two by fours here as you can see we've got about two inches here to interfere with that so i'm going to build out two boards and then cut the board up here to match this which should be a little over three foot here so let's see there to yeah i think 40

4:47 inches is where we're gonna need to be right there and the railing is up on this side had to be a little bit creative with the balusters over here you can see they slope a bit to meet up to this top piece but the primary goal of that little platform is the slide so no worries there so now i've got this side over here done as well you can see turned out really nice very secure so the last portion to do is right here in the front so i need to do kind of the same deal i'll have a board going up here then have a top piece come back down and then i will probably go ahead and put a piece here

5:33 and here as well to go up from that and i can connect the corner for extra strength there and that will be it all the railing is now done took a little bit i got emma down here playing took a little bit to get this corner done but uh it worked out really well i went with the same design and put the bolts through here on those two and it really sure this thing up very nicely so this is going to be pretty good i do believe emma climbed up there and looked out and said oh good now i can't fall off anymore as if she'd already fallen off once she's not so i like it gives a nice opening for the slide

6:18 and everything else is well protected thank you so much for watching this build i know i skipped some of the steps here on the very front but it's all pretty much the same stuff just cutting boards and placing them up there and i just made sure that the balusters were level when i installed them yes if you've enjoyed this portion of the series hit that thumbs up button and be sure to subscribe i have several more parts to go and i think you will enjoy it thanks for watching and i'll see you in the next video bye i'm okay downhill you are uh i am not done

7:06 dad are you all down now i'm all done you want to go to town and get mom a coffee not yet

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Install front Porch Rail. Build a Playhouse 12 — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.