Install an Attic Ladder in 30 Minutes - No Experience Needed
Video by Flannel Guy DIY · 2 moments used in Oak Valley Designs's DIY guides · 14:49 long

Moments in this video
- 10:35–12:30 Trim Ladder Legs to Length
From How to Trim Attic Ladder Legs to the Right Length, Step 2: Mark Cutting Lines on Ladder Legs
Using the manufacturer's provided chart, the presenter determines the precise amount to cut off the bottom of the ladder legs (14 inches for his specific ceiling height). He marks the cut lines on the aluminum ladder rails using a tape measure and a marker, then uses a hacksaw to carefully cut both legs. This ensures the ladder rests on the floor at the correct angle when fully extended.
- 10:35–12:30 Trim Ladder Legs to Length
From How to Trim Attic Ladder Legs to the Right Length, Step 3: Cut Attic Ladder Legs
Using the manufacturer's provided chart, the presenter determines the precise amount to cut off the bottom of the ladder legs (14 inches for his specific ceiling height). He marks the cut lines on the aluminum ladder rails using a tape measure and a marker, then uses a hacksaw to carefully cut both legs. This ensures the ladder rests on the floor at the correct angle when fully extended.
The guide that use this video
Transcript
0:02 hey there everyone before I kill myself on these old attic stairs behind me I'm gonna replace them and if you are looking to install new attic stairs from scratch I'll take you through those steps as well looking at what we have here this old set of attic stairs they're not even safe anymore look at that they don't sit flush the the to the hinges here are basically breaking off look at that and you know I can get up there but it's not safe definitely want to replace them it's time I'm gonna take you through the steps right now but let me just show you what I purchased here I got a new set of stairs I'm going to if you'd like to order online I'll link to to one of the stairs it's similar to
0:47 these down below but I wanted aluminum and the other thing that I did was check the dimensions so made sure that the ceiling height worked for me the ceiling in this garage is nine feet three inches so that works goes up to ten ten foot three the rough opening size 25 by fifty four I measured that before buying these which is important to do now if you're going to install new it's good to go up into your attic and check what the spacing is of your ceiling joists up there and then make a determination as to what size stairs you want to buy based on that so you have to do as little framing work as possible up upstairs and then it shows you the swing
1:33 clearance and the landing space you need but in the garage we have plenty of room there so we're going to go up and take a quick look at the rough opening and see what we're dealing with but I also want to show you the other situation that we have up there with regards to the existing stairs so the rough opening here is just about what we need it might be a quarter inch to two short I'm going to double check that after I get the other ladders at the other ladder out of the package but the other thing is is that this this is definitely is not square I did I did magic that measuring from corner to corner and so I might have to do some trimming of some of these blocks but the other thing I want to do is you know the main the ladder is mainly supported up
2:18 against here where the hinges go so I'm gonna put two by fours here off-camera to block it out and finish the framing okay and then that way we have a secure spot to install the new stairs against what we need to do is provide some bracing underneath these stairs on both ends which you'll watch me do and then we're gonna come up into the attic and cut out the the existing nails that are holding this ladder in with a sawzall and we'll get the stairs out that way drop the new ones in screw them in and it's going to be pretty simple so the first thing I want to do here is take
3:04 this trim off and you know that's also beaten up and the ceiling isn't in great shape I'm expecting a lot of that stuff to start flaking down as I pull that off but the trims got to come off and then we're going to replace it with some new stuff when we're all done so I mentioned that we have to put some bracing across on either end to be able to support not only the old stairs after we cut out the nails that are holding them in but also to support the new stairs to drop them in the slot before
3:52 we reattach them into the into the rough opening so you can see this little reveal here with this little lip right so the idea is to on the bottom of the or on the ceiling of the garage you screw in a 2x4 like this okay and if a stood it on either end with a screw that's going into a ceiling joist so you've got it here like this okay and then you should be able to and one on the other side there's a little reveal as well though not as much and then you should be able to open the stairs while you're still upstairs and climb down and then go get the lag bolts and everything
4:39 else you need to attach it permanently all right now I've got the bracing up there and on both ends I measured it according to what we measure down here on the new ladder and it's basically the same dimensions as the old one so you can still open the door here okay but the frame won't slide down because this frame is being supported there okay so what I'm gonna do now is go up inside with the sawzall cut this at well first I'm gonna hoist this up into the hole through using the ladder so it's up there and then I'm going to cut this out pull this out of the way drop the new one in secure temporarily push the door
5:26 down and come out I'm bringing everything I need in this bucket up to the attic right now it just makes it easier and I already have the sawzall up there the stairs the new stairs are up there and I've got the cordless screw gun I've got a bunch of screws just to hold it in there temporarily I have a drill bit in case I need to pilot hole I have some snips down there for the zip ties that are holding the stairs together I'm supposed to remove those at the end tape measure a square case I need that and make sure that everything is square up there oh I
6:12 got to grab some shims and throw them in here too I came up in the attic now and got the old stairs pulled up behind me I'm gonna get the sawzall out and cut the nails out from around the the perimeter here and you can see I put some additional support behind the where the hinges are going to go and getting pretty hot in here I did install the attic fan recently and you might have seen that video but it hasn't kicked on yet which means it's not quite 95 degrees in here but it feels like it's very close so all you're gonna watch me do here is attach a rope to the stairs so that way
6:59 I can lower it down by myself down to the garage floor okay so um I've decided to knock some of these things out here and and reframe a little bit on this side it's not what was the what was happening with the prior stairs was these short blocks were actually screwed right in to the stairs and they weren't exactly even and also I don't like how that's supported so these are gonna come out I'm gonna put I'm gonna put a 2x4 all the way across to
7:45 the end secure it on both sides and then from there I'm going to put the blocks back or some different sized blocks make sure it's really secure and then we're gonna drop the stairs in and see how it fits well we've got it all framed out now got rid of all the old stuff and feel better about what you see here and the other thing I did here was I didn't like how this wire was exposed so I drilled some holes all the way down after the project's over I'm gonna disconnect it and run the wire through to hide it appropriately so now what we have to do was drop the stairs in and make sure we're all ready to go and make sure it's square it's good I'm gonna
8:43 check for square by measuring diagonally both ways and they need to be about the same distance 58 and a quarter there or the other side awesome same so now I'm gonna temporarily the screws in here on either side just to hold them then I can climb down and take care of the ladder and or secure the sides first and then take care of the ladder and then we're basically done any screws here just temporary just to hold it and
9:42 leverage well we've got the stairs temporarily screwed in and opening them up and it opened nicely and gonna try now shutting it and it looks like it shuts perfectly - I'm very comfortable with how it's aligned so now the next step that I want to take is to adjust the adjust the length of the legs so if I don't adjust the length of the legs you know they make these stairs extra long so that way they can fit ceilings that have a high height okay so it could be maybe you've got 9-foot ceilings ten-foot ceilings in your house or
10:28 you've got a tall garage now you see if I leave these at this length we got that bend here they provide a charc okay and this chart basically tells you depending on how high your ceiling is it tells you how much you need to cut off from the bottom of the ladder so you already measured the edge of the frame down to the floor it's a hundred ten and a quarter inches so here it says if your height is less than 111 inches in more than 110 inches you're going to cut off 14 inches off of the bottom of the ladder we're gonna do that after we cut the 14 inches off we're gonna add these you
11:16 know feet or shoes or whatever you want to call it to the bottom of the ladder and then it bolts in you you pre-drill and bolt it in that way so that's what we're going to do and after we do that then we're going to be able to climb up here and permanently secure the steps in with the lag bolts they provide so now we're ready to cut through this I'm going to use a hacksaw instead of my jigsaw with the metal blade really because most of you are gonna end up using this as well so I'm gonna do it
12:01 old-school and the good part here is it doesn't have to be exactly perfect because the shoes or the bottom of the supports of the ladder are gonna go over this and they've left room for error so I'm just gonna you know we measured well I'm gonna cut down through here and do the other side as well and then we're going to attach the legs so what they want you to do is get this on here and then find us find the spot where the stairs are fully opened and seated properly and then put a mark
12:52 Center hole and then we're gonna drill socket on there we'll tighten it up I'm gonna do the same thing on the other side this feels very strong happy with this [Music]
13:49 now that we have everything secured the lag bolts I can remove the support boards so the last step in the project that really is inconsequential to the installation but we'll make it look a lot better and I'm going to do that off of this video not as not part of this video but afterwards is I've got some extra sheetrock here I'm gonna replace some of that mess that you see around the edge and I have some new trim new pine trim that's gonna go around the perimeter of the opening to make it look all nice so maybe I'll make that part of the thumbnail later when I'm finished with it so anyhow I hope you enjoyed the video I hope this helped you and if you
14:37 have any questions about installing attic stairs please let me know thank you and have a great day if you haven't already hit that subscribe button I would appreciate it if you would do that Thanks
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

