HowTo Install Treads 1080p
Video by Oak Valley Designs · 10 moments used in Oak Valley Designs's DIY guides · 2:18 long
Moments in this video
- 0:09–0:45 Prepare and Clean Stair Treads
From how to clean and maintain carpet stair treads, Step 1: Keep Them Pristine: Weekly Vacuuming
Begin by thoroughly cleaning the stair treads. You can use a microfiber cloth or any suitable cloth, optionally combined with a handheld vacuum, to remove all dust and loose dirt. The goal is to ensure the entire stair surface is clean and completely dry. This is crucial for the adhesive on the back of the carpet treads to stick properly. Avoid using any cleaning products that might leave a greasy residue, such as Pledge or Pine-Sol, as this can compromise the adhesive bond.
- 0:09–0:45 Prepare and Clean Stair Treads
From how to install stair treads without nails or tools, Step 1: Prepare Your Steps: Clean, Dry, and Ready for Treads
Begin by thoroughly cleaning the stair treads. You can use a microfiber cloth or any suitable cloth, optionally combined with a handheld vacuum, to remove all dust and loose dirt. The goal is to ensure the entire stair surface is clean and completely dry. This is crucial for the adhesive on the back of the carpet treads to stick properly. Avoid using any cleaning products that might leave a greasy residue, such as Pledge or Pine-Sol, as this can compromise the adhesive bond.
- 0:48–1:15 Measure and Apply Painter's Tape for Alignment
From how to install stair treads without nails or tools, Step 2: Precision Placement: Measure and Mark Your Centerline
For consistent placement of your carpet treads, measure a 4-inch 'wood reveal' from the wall on each stair. This means the distance from the wall to the inside edge of where the carpet tread will be placed should be 4 inches. Once measured, take a continuous piece of painter's tape and run it down the staircase, aligning its inner edge with your 4-inch mark. This tape will act as a visual guide to ensure all your carpet treads are installed in a straight and aligned manner.
- 1:16–2:09 Install Carpet Treads with Adhesive
From how to measure a U-shaped staircase for carpet stair treads, Step 4: Organize, Order, and Enjoy Your New Stairs!
Take a carpet tread from its box. The easiest and most rewarding part is installation. First, peel off the protective backing from the adhesive strip on the back of the tread. Position the carpet tread by hooking its bullnose (the front edge) underneath the bottom edge of the stair tread. Then, gently pull back on the tread with one hand to ensure it's nice and tight against the bullnose. Once taut, press firmly across the entire surface of the tread, ensuring it adheres securely. Use the painter's tape as a guide to maintain perfect alignment, ensuring everything is straight.
- 1:16–2:09 Install Carpet Treads with Adhesive
From how to install stair treads without nails or tools, Step 2: Precision Placement: Measure and Mark Your Centerline
Take a carpet tread from its box. The easiest and most rewarding part is installation. First, peel off the protective backing from the adhesive strip on the back of the tread. Position the carpet tread by hooking its bullnose (the front edge) underneath the bottom edge of the stair tread. Then, gently pull back on the tread with one hand to ensure it's nice and tight against the bullnose. Once taut, press firmly across the entire surface of the tread, ensuring it adheres securely. Use the painter's tape as a guide to maintain perfect alignment, ensuring everything is straight.
- 1:16–2:09 Install Carpet Treads with Adhesive
From how to install stair treads without nails or tools, Step 3: The Perfect Preview: Dry-Run Your Tread Placement
Take a carpet tread from its box. The easiest and most rewarding part is installation. First, peel off the protective backing from the adhesive strip on the back of the tread. Position the carpet tread by hooking its bullnose (the front edge) underneath the bottom edge of the stair tread. Then, gently pull back on the tread with one hand to ensure it's nice and tight against the bullnose. Once taut, press firmly across the entire surface of the tread, ensuring it adheres securely. Use the painter's tape as a guide to maintain perfect alignment, ensuring everything is straight.
- 1:16–2:09 Install Carpet Treads with Adhesive
From how to install stair treads without nails or tools, Step 4: Clean, Peel, and Stick: Starting from the Top
Take a carpet tread from its box. The easiest and most rewarding part is installation. First, peel off the protective backing from the adhesive strip on the back of the tread. Position the carpet tread by hooking its bullnose (the front edge) underneath the bottom edge of the stair tread. Then, gently pull back on the tread with one hand to ensure it's nice and tight against the bullnose. Once taut, press firmly across the entire surface of the tread, ensuring it adheres securely. Use the painter's tape as a guide to maintain perfect alignment, ensuring everything is straight.
- 1:16–2:09 Install Carpet Treads with Adhesive
From how to install stair treads without nails or tools, Step 5: Secure the Bond: Press from the Center Out
Take a carpet tread from its box. The easiest and most rewarding part is installation. First, peel off the protective backing from the adhesive strip on the back of the tread. Position the carpet tread by hooking its bullnose (the front edge) underneath the bottom edge of the stair tread. Then, gently pull back on the tread with one hand to ensure it's nice and tight against the bullnose. Once taut, press firmly across the entire surface of the tread, ensuring it adheres securely. Use the painter's tape as a guide to maintain perfect alignment, ensuring everything is straight.
- 1:16–2:09 Install Carpet Treads with Adhesive
From how to install stair treads without nails or tools, Step 6: Steps to Success: Repeat and Enjoy Your Safer Stairs!
Take a carpet tread from its box. The easiest and most rewarding part is installation. First, peel off the protective backing from the adhesive strip on the back of the tread. Position the carpet tread by hooking its bullnose (the front edge) underneath the bottom edge of the stair tread. Then, gently pull back on the tread with one hand to ensure it's nice and tight against the bullnose. Once taut, press firmly across the entire surface of the tread, ensuring it adheres securely. Use the painter's tape as a guide to maintain perfect alignment, ensuring everything is straight.
- 1:16–2:09 Install Carpet Treads with Adhesive
From how to prepare and clean stairs before installing carpet treads, Step 1: Time to Peel: Unveiling the Adhesive Backing
Take a carpet tread from its box. The easiest and most rewarding part is installation. First, peel off the protective backing from the adhesive strip on the back of the tread. Position the carpet tread by hooking its bullnose (the front edge) underneath the bottom edge of the stair tread. Then, gently pull back on the tread with one hand to ensure it's nice and tight against the bullnose. Once taut, press firmly across the entire surface of the tread, ensuring it adheres securely. Use the painter's tape as a guide to maintain perfect alignment, ensuring everything is straight.
Guides that use this video
Transcript
0:09 Hi everyone, it's Amy with Oak Valley Designs. I'm going to talk to you about cleaning your stairs in preparation for your new carpet stair treads. So, you can grab a microfiber cloth or any cloth really works. You can do a handheld vacuum or you can use both. And what I like to do is simply take the cloth, make sure you're wiping the entire stair tread, get all of the dust, all of the loose dirt off of here. And the idea is to keep it nice and dry so that the adhesive on the back of your stair tread will really stick nicely. Try to avoid using anything that'll make it greasy, like pledge or pine saw. And that's all you have to do. Install day. Let's make this easy. Grab your painters tape. Let's do a little bit of measuring and then you're ready to put your carpet stair treads down on
0:55 your staircase. If you recall, we have a 4 inch wood reveal. That means from the wall to the inside of the tape, that will be 4 in. Once you measure this, you take one continuous piece of tape, you run it down your staircase, and then you simply put your treads on on the inside of each stair. Okay, the easiest part and the most rewarding part after all your measuring and hard work. These are your treads. They come in a box. Okay, all you do is peel off the back. Throw that in the floor. I've already put a few on, so I'm going to do the top step. Now, you see our painters tape is still here to guide us on the edge. So, everything is in alignment.
1:41 You come to the next step and the first thing you do is hook the bullnose underneath the bottom edge and then pull back with this hand to make sure that it's nice and tight. So, as you press on the front and you pull on the back, put a little pressure across the tread, make sure it's lined up with the painters tape, and that's it. It's that easy.
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.
Subscribe for exclusive updates
Be the first to know about promotions, new products, and sales.