How to repair not replace exterior rotting wood on your house instructions
Video by DO IT YOURSELF ITS EASY · 1 moment used in Oak Valley Designs's DIY guides · 15:21 long

Moments in this video
- 12:26–12:44 Cut and Install Salvaged Timber
From How to Fix a Wobbly Outdoor Stair Railing, Step 4: Repair or Replace Damaged Components
Once the paper template is made, transfer it to a piece of treated wood. Treated wood, or cedar, is recommended for exterior applications to resist further rot. Use an oscillating tool to precisely cut the new timber piece according to the template. This custom-cut piece is then fitted into the severely rotted section and secured in place with screws. This provides structural integrity to areas where the rot was too extensive for filler alone.
The guide that use this video
Transcript
0:02 if you got cracked rotting broken boards on your house this video is going to show you how to fix that and make it look new again thanks for watching i'm going to show you guys how to repair rotting wood when you don't want to replace that whole board especially for you homeowners who don't want to call somebody who's going to charge you 400 to replace a little piece of wood i'm going to show you guys how to fix that and let's do this you got it rotting wood over here as you can see my hand can go through it first step is to remove all the rotting sections chisel here you can use probably any tool you can come up with if you don't have one and a hammer and i'm gonna remove all the rotting sections and even then some go a little extra
0:48 because just in case whatever is causing the rot is being totally removed you get a lot of complaints from people so many trolls on there on the on youtube and all over the internet you just like to reach through the computer or phone or whatever and smack the heck out of them you know why are you searching a how-to video if you're so smart and you're going to be so negative about what's going on on the video or whatever you know you guys need to get a life that's all i got to say to them so pretty much got that i know i got foam on the side over here that's insulation i'm not gonna go that deep this board is only about an inch thick and started to rot because of the rain
1:34 and the seal was bad at the bottom being like the cough or whatnot so all right we're going to clean that up and when you do this you've got to make sure that you clean it good remove any chipping paint don't be scared because you're going to paint the whole piece anyways or at least that section so remove whatever you think is brittle and show you guys what's going on okay so i'm gonna remove any of this like old paint i just bought this house and noticed this and i've done this many times so it works great lasted over 10 years on a previous job i did so no complaints i keep cleaning up don't want to make a boring video for you guys but
2:19 just making sure going that extra mile on this yeah that one's hard you see that over here it's pretty hard pretty tough to take that out so that's good news i removed most of the rot or all so get rid of all that right you got to be sure so [Music] it's not going to be the end of the world there's a little spot of it but you don't want it to be some type of bacteria that's going to keep chiseling away now that i got that cleaned up you can either vacuum or blow it i'm gonna use a blower and blow the heck out of that get it out of our [Music] volt flex way rechargeable awesome tool
3:06 video is not about that let's keep going all right so next step is you're wondering how am i going to fill this thing we are going to use liquid nails interior exterior just make sure if you're doing it outside that yours says exterior this stuff is made to last years and years and years on an exterior environment all right so next we are going to start putting this application in let me zoom in for you guys all right so the first step is you're probably not gonna have a really um nice application in the beginning this is gonna take um a few applications if you're wondering how this is gonna go so this is gonna be the first application i'm gonna go a little extra this is a
3:52 big hole i got if you got a little bit of rotting and stuff like that it'd probably be easier and what i'm using here is just a little cheap scraper nothing special let me zoom out for you guys whole thing all right so this stuff will wanna because it's such a big hole it's gonna want to glob out i may use something to put up against it just to keep that shape maybe a piece of wood or something like that i mean i mean think about what i'm doing now i don't really have to caulk the bottom to keep it away from the rain and the weather because it is caulk that's funny so see it's wanting to drip out i'm gonna make sure i shove it in there
4:37 deep so i know that it's bonding to the walls of what i've done so tomorrow when this is dry i'm gonna come back and hit it again but i'm gonna do it nice and full right now and i'm going to place something there i'll figure out what that what i'm going to do and i'll show you guys so you guys get the idea of what's going on here we're building a form and you want to keep that same texture if you have a little bit artistic ability you can do that the grain of the cedar wood or whatnot i mean just keep it messy looking you know that'll do the job i actually got a nail right there that's causing
5:23 the shape not to hold real good took care of that i don't know if you guys could see that in the video keep that little bumpy texture that's going on with the cedar make it look natural i don't want to make a boring video and keep having you guys watch but i hate when i watch a video and they don't show you how it's done so pretty much that's how it's done right there that's that's step one we're gonna keep coming back and showing you guys day after day until this is completely finished and you guys be the judge and decide whether this is a good idea or do you want to replace the whole board that cedar board probably cost around maybe about 30 bucks and to have it installed by a professional you're probably looking at at least 200
6:09 bucks so you guys decide if you want to do it for less than 20 bucks and do it yourself make yourself proud and feel good about it let's keep watching as the days go on if you don't have a big hole like i have you're not going to have to do this because it's not going to want to drip out i wrapped a piece of wood with wax paper the reason i'm using wax paper is because i don't want this board to get stuck to this wall the only thing that's going to get stuck to this wall is the wax paper which isn't gonna stick and if it even did it wouldn't be the end of the world so i'm gonna press this up against here like that and i'm gonna take a screw and i'm gonna put it in at the end what i'll do is
6:54 uh fill in that screw hole that i made with some liquid nails but now i know when i walk away my kids aren't going to pull this board off and i'm not going to have a glob coming right out actually just had a new roof put on this property and i want to show you guys this is how the roofers left it so i'm going to go up there show you guys how i clean this out we'll get back to the other spot on the garage later that way you guys see the problem that's going on whether it's deep or just slightly on the surface which that one is probably slightly on the surface we'll see when we get up there now if the whole board is rotted you would definitely replace the whole board it's not worth your time but if you've got a little bit of problem and you don't want to deal with hours and hours and tons of
7:41 money on repairs this is a quick fix and it works up here it's a little bit rotted it's doable where it's still tough when i push on it it's still very tough but it has some rotting remove the rotting and i'm gonna scrape all this up i don't have a tripod where i can record this for you guys and i'm up on a roof about 20 feet high so i'm not trying to break a leg but i will show you step by step as i go on section here is just way too far gone i'm not that's just rotted i'm gonna replace what i'm gonna do is uh mark it where it's strong cut it out with an oscillator or whatever tool you have and then replace this section here but as far as like this section goes
8:27 here i'm gonna scrape it away put liquid nails on it make it nice and smooth and we're gonna let it dry and then paint it again i got it all prepped meaning that i got it clean and blown away so right that area i haven't blown away this section here it's really hard to record this up here for you guys just to show you guys this video so really hope you appreciate me being on a roof recording with one hand so i got some on here i put a big glob in there to start to drip down so make sure that you can keep an eye on this especially if it's going to be dripping down like that or else you'll have to cut it off with like a razor blade or something to excess but this is step one right here um as it dries on a thin surface like this you can hit all three coats within probably an hour it's just windy outside nice and dry but
9:15 i removed all the rotting again make sure you remove any loose debris that's step one blow it off either with like a blower or something or just use your breath or whatever works and make sure that you push in there with your tool as you're scraping you know so in the end you'll want to keep that texture going up and down to make it look beautiful and when we paint it everything's gonna look amazing you'll see all right over here i had lots of um loose paint and this is where water falls and hits there so you really need to make sure you just don't put this over it you want to remove all loose debris i hate to keep saying that but i took my razor blade and i scuffed it all up removed all the paint
10:00 and so this wouldn't peel off i've scored it right there and when i'm done with this i'm probably gonna put a bead of this silicone again so it looks nice and smooth and then i'm gonna paint all this when this looks nice but we still got a little bit of a hole there which is gonna take more applications i need to prep that area up better here and i'm still going to fill this in with a piece of wood and go over all this and make sure it's nice and tight waterproof sealed all right this is how i apply it on the flat surface and then i'm going to take my spatula and just rub it you guys could see i really wanted to show you guys me doing this but this is so tough holding this camera if i showed you guys how i was holding this camera on a roof i mean
10:46 look at me so that's what i'm doing for you guys all right again so i couldn't really hire a camera guy in this situation i'm checking if i got the angles just wanted to show you guys how it's done up here so you can see what's happening make sure to get the whole entire wood if it had some rotting like i did right there anywhere where it was a little bit rotting and go over that area even more so that's better had some rotting up in here make sure that you get your tool and you shove that in that crack real good and the second time around when you come when that dries you'll put more
11:33 you don't want to put too much it'll start dripping down so give you guys an idea of what that should look like you see it still has that texture so when you paint this it's going to look amazing i'm going to let all this dry up i'm going to get the piece needed to fill in there and i'm going to hit it with another coat for you guys so you guys can see what's going on i want to show you guys how i captured the shape of the piece needed so it might look a little bit sloppy but it's going to come out perfect again and for all the people who are going to talk crap about what's going on here my question to you is what are you doing searching youtube for a how-to video that's my question to you if you're so smart all right so that's the shape we're going to capture you guys can see i got the shape right there
12:19 i'm going to take this down there and i'm going to cut a piece of wood that looks just like that and we're going to put that in there make sure to use a treated wood if it's outside or cedar this is what i'm dealing with rotting wood i ran out of liquid nails exterior but this is going to work just as good please make sure that it's paintable whatever you're doing see how it says uh paintable and make sure that it's exterior this is where we're at right now filling it in it might shrink a little bit so you're gonna want to come back and check decide if it needs another coat or not this one definitely does this dry up
13:05 see how it shrinks hit it with one more coat and then i'm gonna paint it good as new that part is pretty much done right there and i'm over here this is how i spread it out i'd love to show you guys how it's done but there's no way i can get a tripod up here i'm like literally up on a roof that's 45 degree angle spread this out and show you guys the finished product before it's painted so i waited about a few days maybe it was four days and you could see it's almost perfect and it's pretty solid almost like a rock but rubber so i know i'm not going to deal with that molding again now i'm going to hit it with another coat and see what happens in a couple more days and we're getting somewhere
14:00 all right there's the next coat i only used red so it would really stand out for you guys so you guys could see what's going on but now i use the uh tan one you can see what's going on it's looking real nice and solid once this is painted it's gonna look like some rough saw cedar this will last about probably 15 years or 20 years instead of every three years me coming up here and replacing this board of wood because water runs right down here and rots it i'm not dealing with that and this is where we started the video at and i just pulled the board off it's still wet over here a little bit but i'm gonna hit it with one more coat i'm able to uh just hit it and not have to put the piece of wood back on wait for it to dry a couple more applications you guys get
14:46 the idea what's going on here stuff is getting back to normal and looking like new like a solid piece of look at that that looks great so you guys get the idea once this is dry and it stops shrinking uh then you paint it and you got a solid piece of rubber you didn't have to replace that hole and now what's expensive that's probably a 40 piece of cedar right there and it cost me less than probably five bucks in caulk tubes i think i wasted like two or three of them and you guys get this video helped you out in any way all i ask is you give me a thumbs up thanks for watching take care
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

