powered by

How To Layout Winders Stairs To Allow For Nosing To Line Up At Center Point - Carpenter Training

Video by stairbuilding · 1 moment used in Oak Valley Designs's DIY guides · 3:18 long

Moments in this video

  1. 1:28–2:15 Implement the Nosing Offset Adjustment From How to Lay Out Winder Stairs, Step 6: Mark Stringers for Winder Treads

    To ensure that the tread nosing converges perfectly at the inside corner of the winder stairs, a specific adjustment must be made to the stringer layout. The video explains that each winder step's layout (specifically the riser line and thus the run dimension) must be moved back by the exact measurement of the tread nosing (e.g., typically 1 inch or 1-1/4 inches). This means that when using a framing square to mark the stringer, the measured run for each winder tread must be effectively shortened by the nosing dimension. The goal is that the *leading edge of the tread with its nosing* will align perfectly at the central point, rather than the riser line itself. This offset ensures a clean visual and functional outcome.

The guide that use this video

Transcript

0:01 here is another one of those videos that you're probably not going to find anywhere else except for our Channel until it is copied I should say at least and that will have something to do with having the steps for a Winder that die into the center point here now keep in mind that some building codes still allow this however this is actually the design that the newer building codes would suggest to increase safety and you can apply the same principles that I'm going to share with you here to this one so let let's go ahead and take a look at what the stairway would look like without a nosing so if you're not going to use a nosing you're not going to need this video and your stairs will look something like this and if you don't make any adjustments to the stairway when laying it out then it's going to

0:47 end up looking something like this once you add the nosing and this design right here if built correctly should meet most building codes that allow for this type of design and when I was building stairs this is what I ended up with 99% of the time why you might ask because this information wasn't available to me ever I had to figure some of this stuff out on my own so if I don't make any modifications at all to the layout you're going to end up with something looking like this at the inside corner here and even though we've made some changes the outside corners aren't going to create any noticeable problems next up let's go ahead and take a look at what might be involved if we want the

1:34 nosing to die into the center point and not the risers and that minor adjustment will simply be to move each one of the steps back the length of the nosing and this is what it would look like if we did that let's go ahead and zoom in here and I'm going to go ahead and overlay the other layout design so the other one is this one here from the previous example and this would be the new one where we moved everything back 1 in to allow for our nosing and you can see here where our risers aren't going to be lining up with the center point over here however the Treads with the nosings will so again the secret here is just to Simply move everything back the length

2:20 of the nosing and even though it doesn't look like it right here once I pan up you can see where everything is going to line up with the center Point here and that's how it's done and of course you could finish this corner off with some decorative trim or even some type of a nle post if you don't like the way this finishes over here you can see where the Riser here is coming into this point but it's not coming in to that point over here or over here and don't forget that our Center Point is right here going all the way down to here and has not moved over to here and if all of this makes sense then I've done my job and you have another tool for your stair building or design toolbox and thanks for watching

3:06 to learn more about home building and repairs visit us at our website also don't forget to subscribe for more awesome content see you next time

Automatically transcribed from the source video.

More from the Oak Valley Designs DIY Hub

Read the guide Browse all guides

Planning this project? Shop Oak Valley Designs.

How To Layout Winders Stairs To Allow For Nosing To Line Up At Center Point - Carpenter Training — step-by-step moments | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.