How To Install A Short Regal Ideas Handrail || Dr Decks
Video by drdecks · 1 moment used in Oak Valley Designs's DIY guides · 7:34 long

Moments in this video
- 4:50–5:54 Measure and Cut Handrail
From How to Make Stairs Safer for Seniors, Step 2: Extend Handrails
Place the full-length aluminum handrail into the newly installed brackets to visually determine the desired length. The goal is for the handrail to extend approximately 8 inches past the end of the stair tread vertically. Once the desired length is marked, use a chop saw (miter saw) to precisely cut the aluminum rail. Ensure a clean, straight cut for a professional finish.
The guide that use this video
Transcript
0:02 Hey guys, Dr. Dex here welcome to our channel and thanks for coming if you don't mind I'd appreciate it if you'd please click that subscribe button and hit the bell icon and be notified when we're putting out new content All right, so today we're working on our current deck project and We have an area over here against the house where the client on the old deck They had a grabable handrail. You can kind of see the old Bracket right here, so she requested that we put in a new one just something simple She doesn't want any posts on the staircase or anything like that She just wants something that's mounted to the house. So what we've decided to do is Use these brackets made by regal ideas. They have a complete ADA setup with different railings a top rail that you can use
0:49 Here's a sample of that and we're gonna take this and just do a really small Grappable handrail. I don't know if you can see it on this picture right here, but it's this part right here Just so they have something to grab on to So it's it's not gonna be super complex not complicated But something nice that kind of goes with the flow of this new deck. What I did was I figured out the trajectory or the angle of the stair And what all I had to do is lay down a four foot level on the top of each rise and here's my angle I don't even know what angle it is. I guess we could figure that out. I'd say it's around 22 Oh, it's 22 So usually When you do a staircase if you do two boards wide, you're gonna be in the 32 to 35 degree angle
1:40 And when you go three boards wide during that 20 to 22 degree angle, it's only one step It's not really a hundred percent Not everybody's gonna need this grabable handrail, but that's what the client asked for so that's what they're gonna get So we're gonna mount two of these brackets to the house And then we're just gonna let this rail kind of hang down about eight inches past So it kind of coincides with the end of our stair if you came up vertically So what I did was I took this angle and Then I measured up from my level to code you got up your top rail needs to be between 34 and 38 inches It has to be grabable, which means you know, it has to be within a certain diameter. This is an inch and a half Diameter so it's comfortable to grab onto and it's designed that way
2:28 If your top rail is for a grabable handrail if it's too big it will not pass inspection now This deck is under 30 inches Doesn't require a permit doesn't require an inspection, but we're still gonna build it the way we think we should to make it Proper so we're gonna put our top rail between that 34 and 38 inches probably right around 36 from the tread Nozing is where you got to take your measurement from the tread nosing, but since I have this level on the top of both tread nozzings Then I can measure from down here up and know exactly where my height is also I wanted to cover up this old bracket Okay, so it's been called and it's ready to go But I wanted to cover that up as well just so the homeowners don't have to repaint it and things like that
3:14 So we're just gonna take this and put it right there like that Okay, and then we're gonna take another one and put it right here So that they're in the same plane because if not I would have to take a piece of sighting or piece of this First strip and put it back here somewhere I didn't want to make it too close to these windows or anything like that So we're just gonna mount two right here make that rail go up a little bit past and let hang down a little bit So that they have a place they can actually grab and be safe when they're walking up the stair Okay, so now that that's all said I chose to use some nice star drive Stainless steel screws that went nice with these brackets. They have a nice finish to them So we're gonna go ahead and use those and I'm ready to mount my bracket. Here's a quick tip for you
4:01 I always use a tapered counter or a pre-drill bit makes things go any easier You don't have to go all the way deep But you just want to make sure that you drill that in there With a pre-drill so it doesn't crack out your material when you're installing it So here's the first hole I'm not gonna go hammer on that so sometimes a six inch extension will really help you get around parts So see now I can get it in here get my holes drilled Without messing things up sometimes you might have to turn this up out of the way get your next hole drilled Okay All right, that one's mounted
4:47 Now that we have our brackets mounted we can decide how long to make this grabable rail So I'm just gonna lay it up here another reason why I put this bracket here because I didn't want the rail to coincide with What they have going on here existing? So and the the noticing of the treads here, so I highly doubt they're gonna need to grab past here when they are using it So I'm gonna say somewhere in here is probably a nice distance away And then all that to do is figure out I could just level up from the the nosing and I don't necessarily have to make it all the way to the end of this I could actually Bring it back a little bit more, but there's level Okay, so now I just gotta go cut this on the chop saw and I'll bring it back and then we'll mount it
5:36 So another thing regal halves are these really cool end caps They just kind of finish off a look of the The rail and they're just a plastic pretty much a rubber bumper And they're grooved to fit in this groove right here So he's put them in and you can use your hand or you can tap them on on the ground There we go So that's what that looks like when it's installed Ands are on Now we just have to decide Again where to put this I'd say somewhere in there is great There's actually a couple of lines on the bottom of this Top rail you can look at Under here
6:21 So the center line is kind of what you want to line up for your screw They also come in a kit a number 10 by 3 quarter inch Machine screw that matches color Which is kind of nice and they're a square drive so Let's go back and Line that up One down one to go All right, and that's all there is to it So obviously this is a unique situation But uh will be very effective they also do make loops And hoops and grabs So if you wanted to turn this into a circular grab rail Not on this project
7:08 We just wanted to have something clean and simple that they can grab when they want to access the stairs All right guys thanks for watching. I really appreciate it Hope you learned a little something about grabable handrails and regal ideas if you did Don't forget to click that subscribe button Hit the bell icon to be notified when we're putting out new content Don't forget to like our videos and leave a comment below. I really appreciate it. Thanks for watching Have a great day
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

