How To Calculate Stair Skirt Board Layout Measurement When Steps Are Inconsistent
Video by stairbuilding · 1 moment used in Oak Valley Designs's DIY guides · 4:29 long

Moments in this video
- 2:44–4:14 Cut and Install the Skirt Board
From How to Scribe and Cut a Stair Skirt Board to Fit, Step 3: Cut the Skirt Board
Once all horizontal and vertical lines representing the stair profile are clearly marked on the temporary board, carefully detach it from the wall or stair stringer. Using an appropriate saw (e.g., jigsaw, circular saw, or handsaw), precisely cut along the marked lines. After cutting, position the newly cut skirt board (which is now the finished piece) into its final desired location against the staircase. If you observe any small, unacceptable gaps (e.g., at the inner corners where the riser meets the tread), you can carefully raise the entire skirt board slightly. The 'insurance' measurement added in the previous step should provide enough material to allow for this minor vertical adjustment, ensuring a tight fit at all points. This final adjustment eliminates any remaining small gaps caused by subtle imperfections in the existing stairs.
The guide that use this video
Transcript
0:00 In this video, I will be providing you with information on how you can cut a skirt board for a pre-existing stairway that doesn't have consistent treads or risers. Now, even though all I have are the risers that are inconsistent here, the same thing should work if you have both or just the treads that are inconsistent. So let's go ahead and take a look at our risers. Here we have different riser heights, giving an idea of what we're dealing with, and that will provide us with a gap between the top corner of the steps. And of course, we're going to have at least one high point, and we have that located near the center of the stairway. And I went ahead and matched this board to the bottom angle of the stairway. This is
0:49 the same angle here, and it might not matter if there are only small variations. However, larger variations, maybe over a half inch or three quarters of an inch, might force you to spend a little more time working out the exact position of the skirt board. And of course, you will need to securely connect this board to either the wall or the stairway. It cannot move, and you might be able to do that with some screws at the lower edge here, or below the top of the skirt board, after it has been installed, something where you're not going to be ruining the wall above the skirt board. And of course, there are plenty of other ways to securely fasten this board temporarily, while you lay it out. Next step, we're going to grab our level and then go ahead and go from the
1:36 front of each step and create a level mark all the way up the stairway. And I don't think something like this is going to be that difficult to do. And that should look something like this when you're done. Next thing I want you to do is go to the highest spot or the spot with the largest gap in between the bottom of your skirt board and the top corner of the lowest step. So again, the largest gap in between here and in our situation here, it's seven and three quarter inches. And then I'm going to add a quarter of an inch to that measurement just to provide us with a little insurance. You don't have to do that if you don't want to. Now you don't need to cut a separate board, but I'm going to and I'm going to make mine eight inches tall. And you really don't
2:23 need this board. You could just simply measure from the top of the step up to here and then go to the back and then draw a line, connect the dots kind of a thing. And then I'm going to reposition the board and then mark the top of it again and then reposition it again and mark the top again. And then do the same to the rest of the steps. So I should end up with something like this. And after I've marked everything, it wouldn't be a bad idea to see if we have any spots like this because this is going to provide us with a little gap that might not be acceptable to some of you. And if this is the case, all you need to do is raise all of the lines a little bit and that'll be all of the lines for all of the steps. So you can see here where it's a little different than it is
3:12 down below. And here it looks like we have a bigger gap and all you're doing is compensating for the variations in the steps to make your skirt board work. So hopefully that makes sense because after you've laid everything out, you can go ahead and detach your template or your skirt board so that you can cut it and then after it has been cut, you can go ahead and position it in place. So again, I kind of left this here on purpose to give you an idea of what could happen if you don't increase the measurement a little bit for your template. And you don't have to go a quarter of an inch. You can always go a half inch or three quarters of an inch just to make sure. And of course, it's all going to depend upon how much room you need here, the distance between the top of the
4:00 skirt board and the corner of the steps. And hopefully all of that made sense. However, if it did not, feel free to leave any questions you have in the comment area and I will answer them as soon as possible.
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

