10 Common Repairs when Flipping Furniture, all Found in One Dresser
Video by 365 DIY · 1 moment used in Oak Valley Designs's DIY guides · 17:22 long

Moments in this video
- 9:35–10:24 Patch Holes and Imperfections with Filler
From How to Protect Stairs from Dog Nail Scratches, Step 3: Repair Minor Damage
Inspect all surfaces for nail holes, hardware holes, dings, scratches, or other imperfections. Apply wood filler (or Bondo for larger areas) to these imperfections, pressing it firmly into the holes and gaps. Allow the wood filler to dry completely according to the product's instructions (this can vary but usually takes a few hours). Once dry, sand the patched areas until they are perfectly flush and smooth with the surrounding wood surface. Use a sanding block or power sander as appropriate, ensuring no raised areas or depressions remain. Smooth sanding is critical, as any unevenness will be highlighted by paint. Remember to fill holes before the final paint coat; if you forget, fill it between coats and re-sand.
The guide that use this video
Transcript
0:00 [Music] I'm so excited to flip this dresser I've been wanting to tackle a French provencial dresser after seeing many beautiful flips on YouTube as I looked over this piece I found 10 common things that need patched repaired fixed when flipping furniture and I'm excited to show them to you as we go through this flip my name is Sarah and I like to take things that are ugly and beat up or pulled out of the trash and make them beautiful again welcome to my channel I always start with cleaning a piece of furniture and this brings me to one of the main things I can find in pieces of furniture especially if they've sat out at the curb is some type of mold or mildew and after vacuuming and using a
0:46 good deaser and cleaner and letting it sit in the Sun for hours that can mitigate a lot of mold and mildew however sometimes I need to use vinegar or bleach or whatever it takes to get the wood clean nobody wants mold and mildew in their home wood stains is our number two common repair that I see in drawers it can be something that's like an ink or something you want to clean it as good as you can and if there's still a stain we can bleach it in this piece there's also been water damage which is has damaged both the inside of the piece and the outside on the inside we're going to use this wood bleach and just follow the directions if you're using this and you need a certain amount of of
1:32 the powder to a water ratio I just need a small amount and you first put it on the dark area and let it sit and then you will spread it all over the whole surface that you're working with if it's a tabletop you start with a dark area and Go the whole surface on these drawers the small part and then the whole base of the drawer on the sides of the dresser I start on the bad spot and then go the whole way down and it dries I wipe it off with water and then I repeated this process three times after that that's probably about as good as you're going to get for the stain removal and I think it at least made it a lot better and for the drawers you can also do a light sanding and that will
2:19 help get rid of some of the staining as well our third common repair is bubbling paint this is caused I think from the water damage that we already treated on the inside side and to take care of this I'm going to sand it smooth in order to repaint and I'm being very meticulous to make sure it's very smooth bumps will show up when you paint when you have bare spots you want to put a protective layer so that you don't have bleed through meaning that spot shows up once you're done painting this paint I'm using is Fusion mineral paint it's supposed to cover very well and so I'm testing it one side I sprayed the shellac the other side I did not spray shellac to see if I got bleed through and I actually did not get
3:05 any bleed through so this worked out for me but to air on the side of caution I usually spray some type of protective layer first before painting and the fourth repair that I often find in pieces is gluing things back together that broke whether it's something that split something fell off whatever it is there's usually some type of gluing repair now they're pretty basic you know you get the glue as deep in as you can from whatever is broken I like to use a a dull needle to kind of poke glue back into things and then it needs to clamp my glue bottle says to clamp for 20 to 30 minutes and then let sit and dry for 24 hours I leave it clamped for 24 hours
3:51 this can be timec consuming you want to catch all these as soon as you can cuz depending on how many clamps you have it could take a long time if you need to clamp each part for 24 hours it can speed things up if it's a tiny crack that you can use painters tape as your clamp and that'll free up other clamps number five is similar to number four with broken pieces but this is broken drawers or at least loose drawers is often seen in Furniture repairs that are needed if you're fortunate it's just loose joints and you need to glue them back together this drawer however was glued together with some form of expanding glue probably Gorilla Glue and it took some work to get out if
4:38 you have something like this you want to clean it out really well so that the joints fit back together properly before you glue them now I don't put a ton of glue on my joints and I get this idea from another YouTuber who said in case somebody needs to take this apart in the future you don't want to glue the life out of it just enough to hold it together and make it strong again so once you've got the glue in the joints and not all up and everything but just enough it needs clamped again for 24 hours well if you have enjoyed this video so far or have found this helpful I invite you to hit the like button as we move on to number six which the sixth
5:25 repair that is often seen in flipping Furniture is missing drawer Glides replacing the drawer Glide is actually pretty simple unless you make it complicated this was a 15in drawer I was trying to buy these on Amazon so I could have free delivery and free returns however they only had size 16 in or 14 in so I bought both thinking I would save myself time if one was the wrong size thinking maybe I can make it fit no you can't make them fit you need to buy a 15in drawer Glide if you have a 15in drawer so I paid the stupid text cuz I paid shipping to receive these I had to send them both back at least it was free returns and then I went directly to the company online that sold these and
6:13 bought the 15in because for some reason it was sold there but not on Amazon and I had to pay shipping again but it was the right size and we could get this drawer fixed all right so with the right drawer Glide size we just need to get it snug up in underneath the front of the drawer drawer and make sure it's aligned right nice and tight and then either screw or nail the back end in this came with screws but they look a little too long I'm not comfortable screwing these in I'm afraid it's going to split my wood or go all the way through so I found some tack nails that I was able to just pound these in and I pounded them in and just made sure everything was nice and tight cuz I don't know if you've use drawers where the Glides are loose it can be very annoying when trying to pull a drawer in and out so
6:58 make sure it's good and tight and you're ready to move on repair number seven that I often find in Furniture flips is dealing with the hardware after you've taken it off you can save it for another project if you're not going to use it usually you want to update the hardware if you're updating the piece however this is French provential and I want need to clean this in order to reuse them however one handle did not match the rest so I needed to replace it and I could not find the exact color match uh unless I wanted to spend $50 on a drawer handle I was not willing to do that so I bought the wrong color needed to clean them all and then paint them all so to clean them I boiled them in vinegar water for a few minutes so I can kind of see stuff starting to float off of it then I scrub them down really good now
7:44 these pieces they were Pokey on the back side and I was concerned about it stabbing the drawer front which it already would have cuz they came off of it but I decided to sand them down a little bit and then I didn't dry these right away and my screws all rusted so that added a little extra work of cleaning up my screws so dry these right away after you scrub them down and once they're good and clean and smooth you're ready to paint now I like to do multiple layers of light paint I just use a spray can it's super easy that way and it gets a nice clean finish look so after multiple layers you're ready to go and one tip I like to use old cardboard and if you need to paint the screws you can just easily stick it down into the cardboard and paint the tops really easy
8:30 so once everything's dry you're ready to put them on once your piece is ready and the eighth issue that we often encounter and flipping Furniture is chipping paint with chipping paint you've got to get it smooth when you sand now you could have chipping paint and want to go to be wood it could be you're not sanding it all the way down and you're going to paint over it either way it needs to be smooth you don't want to feel edges so sand sand sand until it's smooth for this piece I wanted the wood raw Edge so I did a lot of hand sanding there and then the whole rest of the piece and all the drawer fronts I needed to very carefully sand and make sure I cleaned up anything that's chipping any holes sand it smooth sand it smooth sand is smooth and while
9:16 I'm at it I'm going to sand up the insides of the drawer too just to give them a refresh if you're sanding down to be wood and there's little cracks and crevices you might have to get a little tool to pick out the paint but you want to get it out and get it smooth we're coming to the end here the ninth issue we often find in almost every piece I flip is some type of holes that need patched whether you're pulling a nail out and you need to fill the hole whether it's Hardware you need to fill the hole or it's dings and scratches and nicks and such that you need to fill in this piece I only use wood filler you can use Bondo if it's a larger space that you need to fill I've shown those in other videos you need to fill the hole let the wood filler or whatever
10:02 you're using dry and then sand it smooth sanding it smooth is also key it will not look good if you don't sand it flush to the piece or like me I forgot to fill the hole and once I put one coat on I had to come back and fill the hole but that's fine I still had a second coat there was no problem but fill your holes sand them smooth in preparation to paint the 10th repair we're going to talk about for this piece is a scuffed up laminate top you may not encounter this too much but on this piece this was dirty it had like nail polish dribbled on it I couldn't leave it as is and I decided to do a light sand to get the junk off I was going to paint this but seeing it with the wood I just couldn't
10:50 bring myself to paint it and try to come up with something that looked really nice to match with the wood and it's not too bad and it's a French provential piece so it kind of is expected to have this laminate top so I wanted to try to save it I reached out on a Facebook group to see if people had an idea cuz I sanded it so I kind of scuffed it up um I you can't see it in the clips that I have I'm sorry best suggestion was to try to buff it or something I'm glad I didn't try to paint this because somebody had the same dresser and they tried multiple different techniques and and products to try to paint this top and nothing would stick so I'm glad I didn't try to paint it and I'm glad I didn't scuff sand too much to ruin it completely I chose to use a clear wax
11:37 and see if I can just kind of buff a shiny is top and since this is an older piece that I'm refinishing I'm okay with it not looking perfect on top it's sad I would rather it be perfect but it's okay this will work um so if you come across the scuffed up laminate maybe try to gently clean it and not use a sander and and then maybe use some type of uh wax or polish of some sorts to get a shine it was recommended not to use a poly coat because they can yellow over time so I opted for the wax so that was my solution for problem number 10 of scuffed up laminate tops while that is the end of our 10 Common patches and repairs that need made with Furniture flips I do have a
12:22 bonus one that involves when the front plate of your dresser is coming apart and you can't just screw it back in what do you do but I also want to show you the finished look of all of this work so let's quickly get through the rest of the steps needed to get this piece finished I'll show you how I problem solved this piece coming apart and then we'll get into the final reveal once everything is swept out wiped down taped off we're ready to paint I did two coats of fusion mineral paints carriage house if You' use a small amount of paint on the brush and be very careful around the edges and Corners this goes on so so nice this was my first project using this paint and I really liked using it
13:07 highly recommend it after I got the two coats of paint on I quickly took off the paint around the feet it is easier and better to take painters tape off while the paint is still damp before it fully dries so we thought this was a pretty simple fix to screw this front plate back in we took the screw out that was there drilled a deeper hole put a deeper screw in it sunk in went flush looked great I waxed the whole piece I did uh the clear wax on the legs along with the whole rest of the piece put the drawer handles on and then brought the piece inside and as I put all the drawers in I realized the bottom right drawer wasn't fitting right and I thought well there's something wrong with it one drawer didn't fit right in the first place so I
13:52 started filing the wood frame thinking I could make room for this drawer but thankfully after after a while I realized oh this is the same side that we screwed in a while back and sure enough I looked there's a little bit of lip on the bottom and that is why the drawer won't fit in correctly so that was frustrating cuz what I thought was in simple fix turned out to not fix it at all so we pulled that screw out I plugged the hole and we drilled a new hole to screw it in and it screwed it in at the exact same spot so we pulled that screw out out and I plugged that hole and we screwed a new hole at a very different angle and when we were screwing that in the woods P
14:39 Oh No so at that point I just needed to walk away but I came back to it and glued this piece back on so that we can try this again so my final thought of how to fix this was to go get a very large clamp and clamp this together right where I want it and then very very carefully screw a pilot hole and then very carefully screw in the screw and it worked it held it together before I even bothered to flip this right side up I checked it with the drawer yep sure enough it fit we're good to go I added nail and Glides to each leg I also used how feeding wax to freshen up the wood it just gives it a nice drink to give it a little more life to last longer and I
15:25 also like to use it on the drawer Glides to help things slide better let's quickly look back and remember what we started with with chipping paint a busted up drawer and some internal staining and let's see what this has turned into to be a piece of furniture to be enjoyed for years to come enjoy this final [Music] reveal [Music]
16:42 [Applause] [Music]
Automatically transcribed from the source video.
More from the Oak Valley Designs DIY Hub
Read the guide Browse all guides
Planning this project? Shop Oak Valley Designs.

